EN ISO 17693:2005
(Main)Footwear - Test methods for uppers - Resistance to damage on lasting (ISO 17693:2004)
Footwear - Test methods for uppers - Resistance to damage on lasting (ISO 17693:2004)
ISO 17693:2004 specifies a test method to determine the lastability of uppers or complete upper assemblies, irrespective of the material used, in order to assess suitability for end use.
Schuhe - Prüfverfahren für Obermaterialien - Aufzwickbarkeit (ISO 17693:2004)
Diese Europäische Norm legt ein Prüfverfahren zur Bestimmung der Aufzwickbarkeit von Obermaterialien oder vollständigem Schuhwerk unabhängig vom Werkstoff fest, um die Gebrauchseigenschaften im fertigen Zustand zu bestimmen.
Chaussures - Méthodes d'essai des tiges - Aptitude au montage (ISO 17693:2004)
L'ISO 17693:2004 spécifie une méthode d'essai permettant de déterminer l'aptitude au montage des tiges ou assemblage complet de la tige, quel que soit le matériau qui les compose afin d'évaluer si elles conviennent à l'utilisation finale.
Footwear - Test methods for uppers - Resistance to damage on lasting (ISO 17693:2004)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-december-2005
Footwear - Test methods for uppers - Resistance to damage on lasting (ISO
17693:2004)
Footwear - Test methods for uppers - Resistance to damage on lasting (ISO
17693:2004)
Schuhe - Prüfverfahren für Obermaterialien - Aufzwickbarkeit (ISO 17693:2004)
Chaussures - Méthodes d'essai des tiges - Aptitude au montage (ISO 17693:2004)
Ta slovenski standard je istoveten z: EN ISO 17693:2005
ICS:
61.060 Obuvala Footwear
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD
EN ISO 17693
NORME EUROPÉENNE
EUROPÄISCHE NORM
September 2005
ICS 61.060 Supersedes EN 13511:2001
English Version
Footwear - Test methods for uppers - Resistance to damage on
lasting (ISO 17693:2004)
Chaussures - Méthodes d'essai des tiges - Aptitude au Schuhe - Prüfverfahren für Obermaterialien -
montage (ISO 17693:2004) Aufzwickbarkeit (ISO 17693:2004)
This European Standard was approved by CEN on 26 August 2005.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Central Secretariat or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,
Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2005 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 17693:2005: E
worldwide for CEN national Members.
Foreword
The text of ISO 17693:2004 has been prepared by Technical Committee ISO/TC 216 "Footwear"
of the International Organization for Standardization (ISO) and has been taken over as EN ISO
17693:2005 by Technical Committee CEN/TC 309 "Footwear", the secretariat of which is held by
AFNOR.
This European Standard shall be given the status of a national standard, either by publication of
an identical text or by endorsement, at the latest by March 2006, and conflicting national
standards shall be withdrawn at the latest by March 2006.
This document supersedes EN 13511:2001.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Cyprus,
Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Endorsement notice
The text of ISO 17693:2004 has been approved by CEN as EN ISO 17693:2005 without any
modifications.
INTERNATIONAL ISO
STANDARD 17693
First edition
2004-10-15
Footwear — Test methods for uppers —
Resistance to damage on lasting
Chaussures — Méthodes d'essai des tiges — Aptitude au montage
Reference number
ISO 17693:2004(E)
©
ISO 2004
ISO 17693:2004(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 2004
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2004 – All rights reserved
ISO 17693:2004(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 17693 was prepared by the European Committee for Standardization as EN 13511:2001. This
International Standard includes corrigendum EN 13511:2001/AC:2003 and was adopted under a special
“fast-track procedure” by Technical Committee ISO/TC 216, Footwear in parallel with its approval by the ISO
member bodies.
Throughout the text of this document, read “.this European Standard.” to mean “.this International
Standard.”.
ISO 17693:2004(E)
EN 13511:2001 (E)
1 Scope
This European Standard specifies a test method to determine the lastability of uppers or complete upper assembly
irrespective of the material in order to assess the suitability for the end use.
2 Normative references
This European Standard incorporates by dated or undated reference, provisions from other publications. These
normative references are cited at the appropriate places in the text, and the publications are listed hereafter. For
dated references, subsequent amendments to or revisions of any of these publications apply to this European
Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the
publication referred to applies (including amendments).
EN 12222, Footwear - Standard atmospheres for conditioning and testing of footwear and components for
footwear.
prEN ISO 2418, Leather - Chemical, physical, mechanical and fastness tests – Sampling.
3 Terms and definitions
For the purposes of this European St
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.