iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

EN ISO 2507-3:2017

(Main)

Thermoplastics pipes and fittings - Vicat softening temperature - Part 3: Test conditions for acrylonitrile/butadiene/styrene (ABS) and acrylonitrile/styrene/acrylic ester (ASA) pipes and fittings (ISO 2507-3:1995)

Thermoplastics pipes and fittings - Vicat softening temperature - Part 3: Test conditions for acrylonitrile/butadiene/styrene (ABS) and acrylonitrile/styrene/acrylic ester (ASA) pipes and fittings (ISO 2507-3:1995)

Specifies the particular test conditions for determining the Vicat softening temperature of ABS and ASA pipes and fittings (the general test method is given in ISO 2507-1). Also gives, for information, the corresponding basic specifications.

Rohre und Formstücke aus Thermoplasten - Vicat-Erweichungstemperatur - Teil 3: Prüfbedingungen für Rohre und Formstücke aus Acrylnitril-Butadien-Styrol (ABS) und Acrylnitril-Styrol-Acrylester (ASA) (ISO 2507-3:1995)

Dieser Teil von ISO 2507 legt die spezifischen Testbedingungen zur Ermittlung der Vicat-Erweichungstemperatur von Rohren und Formstücken aus Acrylnitril-Butadien-Styrol (ABS) und Acrylnitril-Styrol-Acrylester (ASA) fest.
Außerdem sind zur Information die entsprechenden grundlegenden Festlegungen enthalten.
ANMERKUNG 1   Das allgemeine Prüfverfahren zur Ermittlung der Vicat-Erweichungstemperatur von Rohren und Formstücken aus Thermoplasten ist in ISO 2507-1 angegeben.

Tubes et raccords en matières thermoplastiques - Température de ramollissement Vicat - Partie 3: Conditions particulières d'essai pour tubes et raccords en acrylonitrile/butadiène/styrène (ABS) et en acrylonitrile/styrène/ester acrylique (ASA) (ISO 2507-3:1995)

L’IEC 60679-1:2017 spécifie les exigences générales relatives aux oscillateurs piézoélectriques, diélectriques et électrostatiques, y compris les oscillateurs à résonateur diélectrique (DRO - Dielectric Resonator Oscillators) et les oscillateurs à résonateurs à ondes acoustiques de volume à couches (FBAR) (ci-après dénommés "Oscillateur"), sous assurance qualité par les procédures d’agrément de savoir-faire ou les procédures d’homologation.
NOTE Les oscillateurs DRO et FBAR sont à l’étude.
Cette édition inclut les modifications techniques majeures suivantes par rapport à l'édition précédente:
a) le titre a été modifié;
b) des éléments supplémentaires relatifs aux oscillateurs utilisant un résonateur OAS ou MEMS ont été ajoutés dans "Termes, définitions et informations générales";
c) les méthodes de mesure de l’IEC 60679-1:2007 ont été supprimées (elles seront intégrées à la série IEC 62884);
d) le contenu de l’Annexe A a été enrichi;
e) un nouveau terme et sa définition, “DIXO” (digital interfaced crystal oscillator - oscillateur à quartz à interface numérique), ont été ajoutés;
f) un nouveau terme et sa définition, “SSXO” (spread spectrum crystal oscillator - oscillateur à quartz à spectre étalé), ont été ajoutés;
g) l’Annexe D a été ajoutée.

Plastomerne cevi in fitingi - Temperatura zmehčišča po Vicatu - 3. del: Preskusni pogoji za cevi in fitinge iz akrilonitril/butadien/stirena (ABS) in akrilonitril/stiren/akril estra (ASA) (ISO 2507-3:1995)

Določa posebne preskusne pogoje za določevanje temperature zmehčišča Vicat cevi ter fitingov ABS in ASA (splošna preskusna metoda je podana v standardu ISO 2507-1). Podaja tudi ustrezne osnovne specifikacije za informativne namene.

General Information

Status
Published
Publication Date
17-Oct-2017
Withdrawal Date
30-Oct-2020
ICS
23.040.20 - Plastics pipes
23.040.45 - Plastics fittings
Technical Committee
CEN/TC 155 - Plastics piping systems and ducting systems
Drafting Committee
CEN/TC 155 - Plastics piping systems and ducting systems
Current Stage
6060 - Definitive text made available (DAV) - Publishing
Start Date
18-Oct-2017
Due Date
30-Mar-2019
Completion Date
18-Oct-2017
Ref Project
SIST EN ISO 2507-3:2018 - Thermoplastics pipes and fittings - Vicat softening temperature - Part 3: Test conditions for acrylonitrile/butadiene/styrene (ABS) and acrylonitrile/styrene/acrylic ester (ASA) pipes and fittings (ISO 2507-3:1995)

Relations

Replaces
EN 727:1994 - Plastics piping and ducting systems - Thermoplastics pipes and fittings - Determination of Vicat softening temperature (VST)
Effective Date
08-Jun-2022

Buy Standard

EN ISO 2507-3:2018EN ISO 2507-3:2018
PreviousNext
Standard
EN ISO 2507-3:2018
English language
9 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


SLOVENSKI STANDARD
01-januar-2018
1DGRPHãþD
SIST EN 727:1997
3ODVWRPHUQHFHYLLQILWLQJL7HPSHUDWXUD]PHKþLãþDSR9LFDWXGHO3UHVNXVQL
SRJRML]DFHYLLQILWLQJHL]DNULORQLWULOEXWDGLHQVWLUHQD $%6 LQ
DNULORQLWULOVWLUHQDNULOHVWUD $6$  ,62
Thermoplastics pipes and fittings - Vicat softening temperature - Part 3: Test conditions
for acrylonitrile/butadiene/styrene (ABS) and acrylonitrile/styrene/acrylic ester (ASA)
pipes and fittings (ISO 2507-3:1995)
Rohre und Formstücke aus Thermoplasten - Vicat-Erweichungstemperatur - Teil 3:
Prüfbedingungen für Rohre und Formstücke aus Acrylnitril-Butadien-Styrol (ABS) und
Acrylnitril-Styrol-Acrylester (ASA) (ISO 2507-3:1995)
Tubes et raccords en matières thermoplastiques - Température de ramollissement Vicat
- Partie 3: Conditions particulières d'essai pour tubes et raccords en
acrylonitrile/butadiène/styrène (ABS) et en acrylonitrile/styrène/ester acrylique (ASA)
(ISO 2507-3:1995)
Ta slovenski standard je istoveten z: EN ISO 2507-3:2017
ICS:
23.040.20 Cevi iz polimernih materialov Plastics pipes
23.040.45 Fitingi iz polimernih Plastics fittings
materialov
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN ISO 2507-3
EUROPEAN STANDARD
NORME EUROPÉENNE
October 2017
EUROPÄISCHE NORM
ICS 23.040.20; 23.040.45 Supersedes EN 727:1994
English Version
Thermoplastics pipes and fittings - Vicat softening
temperature - Part 3: Test conditions for
acrylonitrile/butadiene/styrene (ABS) and
acrylonitrile/styrene/acrylic ester (ASA) pipes and fittings
(ISO 2507-3:1995)
Tubes et raccords en matières thermoplastiques - Rohre und Formstücke aus Thermoplasten - Vicat-
Température de ramollissement Vicat - Partie 3: Erweichungstemperatur - Teil 3: Prüfbedingungen für
Conditions particulières d'essai pour tubes et raccords Rohre und Formstücke aus Acrylnitril-Butadien-Styrol
en acrylonitrile/butadiène/styrène (ABS) et en (ABS) und Acrylnitril-Styrol-Acrylester (ASA) (ISO
acrylonitrile/styrène/ester acrylique (ASA) (ISO 2507- 2507-3:1995)
3:1995)
This European Standard was approved by CEN on 19 September 2017.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2017 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 2507-3:2017 E
worldwide for CEN national Members.

Contents Page
European foreword . 3

European foreword
The text of ISO 2507-3:1995 has been prepared by Technical Committee ISO/TC 138 “Plastics pipes,
fittings and valves for the transport of fluids” of the International Organization for Standardization
(ISO) and has been taken over as EN ISO 2507-3:2017 by Technical Committee CEN/TC 155 “Plastics
piping systems and ducting systems” the secretariat of which is held by NEN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by April 2018, and conflicting national standards shall be
withdrawn at the latest by April 2020.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 727:1994.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The text of ISO 2507-3:1995 has been approved by CEN as EN ISO 2507-3:2017 without any
modification.
INTERNATIONAL
ISO
STANDARD
2507-3
First edition
1995-02-15
Thermoplastics pipes and fittings -
Vicat softening temperature -
Part 3:
Test conditions for
acrylonitrile/butadiene/styrene (ABS) and
acrylonitri
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN ISO 7510:2024(Main)
Plastics piping systems - Glass-reinforced plastics (GRP) components - Determination of the amounts of constituents (ISO 7510:2017)
SIST EN ISO 7510:2024

ISO 7510:2017 specifies a method for the determination of constituent materials of a test sample cut from a glass-reinforced plastics (GRP) component intended for use in a piping system. It includes determination of resin, glass, aggregate and filler contents.
It is also applicable to the determination of the type and arrangement of the reinforcements. If used to determine the amounts of constituent materials in layered constructions it may be necessary to separate the laminate layers by cutting or splitting and testing each separately.

  • Standard
    12 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 12201-3:2024(Main)
Plastics piping systems for water supply, and for drains and sewers under pressure - Polyethylene (PE) - Part 3: Fittings
SIST EN 12201-3:2024

This document specifies the characteristics of fusion fittings made from polyethylene (PE) as well as of mechanical fittings for buried and above ground applications, intended for the conveyance of water for human consumption, raw water prior to treatment, drains and sewers under pressure, vacuum sewer systems, and water for other purposes, with the exception of industrial application.
NOTE 1   For PE components intended for the conveyance of water for human consumption and raw water prior to treatment, attention is drawn to subclause 6.6 of this document. Components manufactured for water for other purposes, drains and sewers, and vacuum sewer systems are possibly not suitable for water supply for human consumption.
NOTE 2   Industrial application is covered by EN ISO 15494 [4].
The intended uses include sea outfalls, laid in water and pipes suspended below bridges.
It also specifies the test parameters for the test methods referred to in this document.
In conjunction with EN 12201-1, EN 12201 2, EN 12201 4 and EN 12201 5, this document is applicable to PE pipes, fittings and valves, their joints and joints with components of PE and other materials intended to be used under the following conditions:
a)   allowable operating pressure, PFA, up to 25 bar  ;
b)   an operating temperature of 20 °C as a reference temperature.
NOTE 3   For applications operating at constant temperature greater than 20 °C and up to and including 50 °C, see EN 12201-1:2024, Annex A.
The EN 12201 series covers a range of allowable operating pressures and gives requirements concerning colours.
NOTE 4   It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and any relevant national guidance or regulations and installation practices or codes.
These fittings can be of the following types:
—   electrofusion socket fittings;
—   electrofusion saddle fittings;
—   spigot end fittings (for butt fusion using heated tools and electrofusion socket fusion);
—   socket fusion fittings (see Annex A);
—   mechanical fittings;
—   fabricated fittings (see Annex B).

  • Standard
    43 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 13267:2023(Main)
Thermoplastics piping systems for non-pressure underground drainage and sewerage - Thermoplastics inspection chamber and manhole bases - Test methods for buckling resistance (ISO 13267:2022)
SIST EN ISO 13267:2023

This document specifies methods of test for the resistance of the base of thermoplastics inspection chambers and manholes to external soil and ground-water pressure after installation.

  • Standard
    18 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 13268:2023(Main)
Thermoplastics piping systems for non-pressure underground drainage and sewerage - Thermoplastics shafts or risers for inspection chambers and manholes - Determination of ring stiffness (ISO 13268:2022)
SIST EN ISO 13268:2023

This document specifies a test method for assessing the initial (short-term) tangential ring stiffness of riser shafts for thermoplastics inspection chambers or manholes.

  • Standard
    16 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 13266:2023(Main)
Thermoplastics piping systems for non-pressure underground drainage and sewerage - Thermoplastics shafts or risers for inspection chambers and manholes - Determination of resistance against surface and traffic loading (ISO 13266:2022)
SIST EN ISO 13266:2023

This document specifies a method of testing the resistance of the upper assembly of inspection chambers and manhole components against surface and traffic loading.
It is not applicable to requirements for testing the cover and frame. Those requirements are specified in EN 124-1 or other standards, depending on the material.
NOTE    Upper assembly components normally include shafts or risers, cones, telescopic adapters and near surface components.

  • Standard
    13 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
CEN/TS 17176-3:2022(Main)
Plastics piping systems for water supply and for buried and above ground drainage, sewerage and irrigation under pressure - Oriented unplasticized poly(vinyl chloride) (PVC-O) - Part 3: Fittings
SIST-TS CEN/TS 17176-3:2022

This document specifies the characteristics of solid-wall oriented unplasticized poly(vinyl chloride) (PVC-O) fittings for piping systems intended for water supply and for buried drainage, sewerage, treated waste water and irrigation under pressure or above-ground where protected from direct sunlight. The scope of this document is limited to double sockets, repair couplings, reducers and to non-end load bearing elbows.
NOTE 1   The scope of this document is restricted to fittings on the market during the preparation of this document. Therefore, tees, flange adaptors, etc., are excluded from this version of the standard.
NOTE 2   For double sockets, repair couplings and reducers there are no special fittings designs for end-load bearing applications. However, restrained gaskets can be used for end-load bearing applications. In that case, the requirements of EN 17176-5 are applicable.
It also specifies the test parameters for the test methods referred to in this document.
In conjunction with EN 17176-1 and EN 17176-5, this document is applicable to oriented PVC-O fittings intended to be used for the following:
a)   water mains and services lines;
b)   conveyance of water for both outside and inside buildings;
c)   drainage, sewerage and treated waste water under pressure;
d)   irrigation under pressure.
This document is applicable to piping systems intended for the supply of water with a maximum allowable operating pressure (PFA) up to and including 25 bar . The piping system according to this document is intended for the conveyance of cold water up to and including 45 °C and especially in those applications where special performance requirements are needed, such as impact loads and pressure fluctuations. For temperatures between 25 °C and 45 °C, EN 17176-2:2019, Figure C.1 applies.
This document specifies a range of fittings sizes and pressure classes and gives a requirement and recommendations concerning colours.
NOTE 3   It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and any relevant national regulations and installation practices or codes.

  • Technical specification
    24 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 11296-4:2018/A1:2021(Amendment)
Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks - Part 4: Lining with cured-in-place pipes - Amendment 1: Updated definitions, marking requirements and procedure for alternative expression of flexural test results (ISO 11296-4:2018/Amd 1:2021)
SIST EN ISO 11296-4:2018/A1:2021

2021-02-11 - TC decision is missing to skip FV.

  • Amendment
    12 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
CEN/TS 1046:2021(Main)
Thermoplastics piping and ducting systems - Outside the building structures for gravity and pressurised systems - Trench installation
SIST-TS CEN/TS 1046:2021

This document gives the recommended practise for underground open trench installation and commissioning of thermoplastics piping systems to be used for the conveyance of water under pressure (in addition to EN 805) and for the discharge of wastewater under gravity (in addition to EN 1610) .
In the field of non-pressure underground drainage and sewerage this is reflected in the marking of products by application code "U" and "UD":
-   outside the building structure (U);
-   both buried in ground within the building structure (application area code "D") and outside the
building (application area code "UD").
This document covers also installation and/or connections to valves, manholes, inspection chambers, gullies and other ancillary components in piping systems.
NOTE 1   Code of practise for pipelines for gas supply is covered by EN 12007-series [21].
NOTE 2   Recommended practices for installation of plastic piping systems for soil and waste discharge within the building structure is covered by CEN/TR 13801 [12].
NOTE 3   Practices for underground installation of rainwater infiltration and storage attenuation systems are covered by CEN/TR 17179 [13].
NOTE 4   It is assumed that additional recommendations and/or requirements are detailed in the individual product standards.
NOTE 5    If non-plastic components are part of the plastic system the manufacturer's instructions should be taken into account.
Requirements and instructions concerning commissioning of systems can be found in EN 805 and EN 1610 and the relevant national and/or local regulations. This document gives specific additional recommendations for commissioning relevant for plastic piping systems.
Attention is drawn to any relevant local and/or national regulations (e.g. health, safety and hygienic requirements).

  • Technical specification
    31 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 11298-4:2021(Main)
Plastics piping systems for renovation of underground water supply networks - Part 4: Lining with cured-in-place pipes (ISO 11298-4:2021)
SIST EN ISO 11298-4:2021

This document, in conjunction with ISO 11298‑1, specifies requirements and test methods for cured-in-place pipes and fittings used for the renovation of water supply networks, which transport water intended for human consumption, including raw water intake pipelines.
It applies to independent (fully structural, class A) and interactive (semi structural, class B) pressure pipe liners, as defined in ISO 11295, which do not rely on adhesion to the existing pipeline. It applies to the use of various thermosetting resin systems, in combination with compatible fibrous carrier materials, reinforcement, and other process-related plastics components (see 5.1).
It does not include requirements or test methods for resistance to cyclic loading or the pressure rating of CIPP liners where passing through bends, which are outside the scope of this document.
It is applicable to cured-in-place pipe lining systems intended to be used at a service temperature of up to 25 °C.
NOTE   For applications operating at service temperatures greater than 25 °C, guidance on re-rating factors can be supplied by the system supplier.

  • Standard
    49 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 17176-5:2019(Main)
Plastics piping systems for water supply and for buried and above ground drainage, sewerage and irrigation under pressure - Oriented unplasticized poly(vinyl chloride) (PVC-O) - Part 5: Fitness for purpose of the system
SIST EN 17176-5:2019

This part of FprEN 17176 specifies the characteristics of the fitness for purpose of oriented unplasticized poly(vinyl chloride) (PVC-O) solid wall piping systems intended for water supply and for buried drainage, sewerage, treated waste water and irrigation under pressure or above-ground where protected from direct sunlight. It also specifies the test parameters for the test methods referred to in this document.
NOTE 1   This document is not intended for on-site testing of pipe systems.
In conjunction with FprEN 17176-1, FprEN 17176-2, FprCEN/TS 17176-3 and EN ISO 1452-3, it is applicable to PVC-O pipes, PVC-O fittings, their joints and to joints with components of other plastics and non-plastics materials intended to be used for the following:
a)   water mains and services lines;
b)   conveyance of water for both outside and inside buildings;
c)   drainage and sewerage under pressure;
d)   irrigation under pressure.
Joints constructed of other materials shall meet their own standards in addition to the fitness of purpose requirements specified in this document.
It is applicable to piping systems intended for the supply of water with a maximum allowable operating pressure (PFA) up to and including 25 bar . The piping system according to this document is intended for the conveyance of cold water up to and including 45 °C and especially in those applications where special performance requirements are needed, such as impact loads and pressure fluctuations.
For temperatures between 25 °C and 45 °C, FprEN 17176-2:2018, Figure C.1 applies.
NOTE 2   It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and any relevant national regulations and installation practices or codes.

  • Standard
    12 pages
    English language
    sale 10% off
    e-Library read for
    1 day