23.040.20 - Plastics pipes
Plastics pipes
Kunststoffrohre
Canalisations en matieres plastiques
Cevi iz polimernih materialov
General Information
This document specifies the requirements for solid wall pipes with smooth internal and external surfaces, extruded from the same formulation throughout the wall, fittings and the system of unplasticized poly(vinyl chloride) (PVC-U) piping systems intended for soil and waste discharge applications (low and high temperature):
- inside buildings (application area code "B");
- for both inside buildings and buried in ground within the building structure (application area code "BD").
NOTE 1 The int...view more
- Standard46 pagesEnglish language
sale 10% off- e-Library read for1 day
- Draft47 pagesEnglish language
sale 10% off- e-Library read for1 day
This document provides a scheme for the assessment of conformity of PE products and assemblies for the rehabilitation of existing pipelines, in accordance with the applicable parts of ISO 11296, ISO 11297, ISO 11298, ISO 11299 and ISO 21225, and intended to be included in the manufacturer's quality plan as part of the quality management system and for the establishment of certification procedures.
NOTE In order to help the reader, summary tables of overall scheme requirements are provided in An...view more
- Technical specification54 pagesEnglish language
sale 10% off- e-Library read for1 day
- Technical specification51 pagesEnglish language
sale 10% off- e-Library read for1 day
- Standard2 pagesEnglish language
sale 15% off- Draft2 pagesEnglish language
sale 15% off- Draft2 pagesEnglish language
sale 15% off- Draft2 pagesFrench language
sale 15% off
- Draft2 pagesEnglish language
sale 15% off- Standard2 pagesEnglish language
sale 15% off- Draft2 pagesFrench language
sale 15% off- Draft2 pagesEnglish language
sale 15% off
- Draft2 pagesEnglish language
sale 15% off- Standard2 pagesEnglish language
sale 15% off- Draft3 pagesFrench language
sale 15% off- Draft3 pagesEnglish language
sale 15% off
- Standard4 pagesEnglish language
sale 15% off- Draft4 pagesEnglish language
sale 15% off- Draft3 pagesFrench language
sale 15% off- Draft4 pagesEnglish language
sale 15% off
- Standard3 pagesFrench language
sale 15% off- Draft3 pagesFrench language
sale 15% off- Standard3 pagesEnglish language
sale 15% off- Draft3 pagesEnglish language
sale 15% off- Draft3 pagesEnglish language
sale 15% off
- Draft5 pagesFrench language
sale 15% off- Standard4 pagesFrench language
sale 15% off- Draft4 pagesEnglish language
sale 15% off- Standard4 pagesEnglish language
sale 15% off- Draft5 pagesEnglish language
sale 15% off
- Standard2 pagesFrench language
sale 15% off- Draft1 pageFrench language
sale 15% off- Standard2 pagesEnglish language
sale 15% off- Draft2 pagesEnglish language
sale 15% off- Draft2 pagesEnglish language
sale 15% off
This part of ISO 6259 specifies a method of determining the tensile properties of pipes made of unplasticized poly(vinyl chloride) (PVC-U), oriented unplasticized poly(vinyl chloride) (PVC-O), chlorinated poly(vinyl chloride) (PVC-C) and high-impact poly(vinyl chloride) (PVC-HI), and in particular the following properties:
— the stress at yield;
— the stress and the elongation at break.
- Standard19 pagesEnglish language
sale 10% off- e-Library read for1 day
- Draft15 pagesEnglish language
sale 10% off- e-Library read for1 day
This document specifies a method for determining the tensile properties of pipes made of unplasticized poly(vinyl chloride) (PVC-U), oriented unplasticized poly(vinyl chloride) (PVC-O), chlorinated poly(vinyl chloride) (PVC-C) and high-impact poly(vinyl chloride) (PVC-HI, PVC-M or PVC-A), and in particular the following properties: — the stress at yield and stress at break; — the elongation at break. NOTE The general method of test for the determination of the tensile properties of thermoplastic...view more
- Standard12 pagesFrench language
sale 15% off- Standard11 pagesEnglish language
sale 15% off- Draft12 pagesFrench language
sale 15% off- Draft12 pagesEnglish language
sale 15% off
This document specifies the characteristics of pipes (mains, sub-mains and laterals) made from polyethylene (PE), intended for the conveyance of water for irrigation, at a water temperature up to 45 °C. NOTE 1 For the effect of water temperature on the maximum operating pressure, see Annex A. This document applies to pipes that will not be subjected to internal pressure for long periods, and not more than 1 500 hours/year. For piping applications with long-term continuous pressure, the ISO 4427 ...view more
- Standard13 pagesEnglish language
sale 15% off- Draft13 pagesEnglish language
sale 15% off
This document specifies a test method for determining the leaktightness of elastomeric sealing ring type joints for buried thermoplastics non-pressure piping systems. Unless otherwise specified in the referring standard, the tests are carried out at the following basic test pressures: — p1: internal negative air pressure (partial vacuum); — p2: a low internal hydrostatic pressure; — p3: a higher internal hydrostatic pressure. It also describes the following four test conditions under which the t...view more
- Standard10 pagesEnglish language
sale 15% off- Standard11 pagesFrench language
sale 15% off- Draft10 pagesEnglish language
sale 15% off
This document specifies six test methods for the determination of the initial circumferential tensile wall strength per unit of length of glass-reinforced thermosetting plastics (GRP) pipes. NOTE Another commonly used term for "circumferential tensile strength" is "hoop tensile strength" and the two expressions can be used interchangeably. The burst test (method A) is suitable for all types and sizes of pipes. It is considered the reference method. However, all the methods in this document have ...view more
- Standard20 pagesEnglish language
sale 15% off- Draft20 pagesEnglish language
sale 15% off
This document provides a scheme for the assessment of conformity of PE products and assemblies for the rehabilitation of existing pipelines, in accordance with the applicable parts of ISO 11296, ISO 11297, ISO 11298, ISO 11299 and ISO 21225, and intended to be included in the manufacturer's quality plan as part of the quality management system and for the establishment of certification procedures. NOTE In order to help the reader, summary tables of overall scheme requirements are provided in Ann...view more
- Technical specification44 pagesEnglish language
sale 15% off
- Standard2 pagesEnglish language
sale 15% off
This document, together with ISO 21138‑1, specifies the definitions and requirements for pipes with a non-smooth external surface and a smooth internal surface (Type B), fittings and systems based on unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) structured-wall piping systems intended to be used in non-pressure underground drainage and sewerage applications. NOTE 1 Pipes, fittings and the systems complying with this document can also be used for highway dra...view more
- Standard38 pagesEnglish language
sale 15% off
This document, together with ISO 21138‑2 and ISO 21138‑3, specifies the definitions and requirements for pipes, fittings and systems based on unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) structured-wall piping systems intended to be used in non-pressure underground drainage and sewerage applications. NOTE 1 Pipes, fittings and the system complying with this document can also be used for highway drainage and surface water. This document covers a range of pi...view more
- Standard17 pagesEnglish language
sale 15% off
This document, together with ISO 21138-1, specifies the definitions and requirements for pipes with smooth external and internal surfaces (Type A), fittings and systems based on unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) structured-wall piping systems intended to be used in non-pressure underground drainage and sewerage applications. NOTE 1 Pipes, fittings and the system complying with this document can also be used for highway drainage and surface water...view more
- Standard39 pagesEnglish language
sale 15% off
This document gives guidance for the assessment of conformity of materials, products, joints and assemblies in accordance with the applicable part(s) of EN 1451 intended to be included in the manufacturer’s quality plan as part of the quality management system and for the establishment of third-party certification procedures.
NOTE 1 The quality management system is expected to conform to or is no less stringent than the relevant requirements to EN ISO 9001 [1].
NOTE 2 If third-party certificat...view more
- Technical specification22 pagesEnglish language
sale 10% off- e-Library read for1 day
- Technical specification22 pagesEnglish language
sale 10% off- e-Library read for1 day