EN ISO 13267:2023
(Main)Thermoplastics piping systems for non-pressure underground drainage and sewerage - Thermoplastics inspection chamber and manhole bases - Test methods for buckling resistance (ISO 13267:2022)
Thermoplastics piping systems for non-pressure underground drainage and sewerage - Thermoplastics inspection chamber and manhole bases - Test methods for buckling resistance (ISO 13267:2022)
This document specifies methods of test for the resistance of the base of thermoplastics inspection chambers and manholes to external soil and ground-water pressure after installation.
Kunststoff-Rohrleitungssysteme aus Thermoplasten für erdverlegte drucklose Abwasserkanäle und -leitungen - Böden von Kontroll- und Einsteigschächten aus Thermoplasten - Prüfverfahren für die Widerstandsfähigkeit gegen Einbeulen (ISO 13267:2022)
Dieses Dokument legt Prüfverfahren für die Widerstandsfähigkeit des Schachtbodens von Kontroll- und Einsteigschächten aus thermoplastischen Kunststoffen gegen äußeren Boden- und Wasserdruck nach dem Einbau fest.
Systèmes de canalisations thermoplastiques pour branchements et collecteurs d'assainissement enterrés sans pression - Éléments de fond de boîtes d'inspection et de branchement et de regards thermoplastiques - Méthode d'essai de résistance au flambage (ISO 13267:2022)
Le présent document spécifie des méthodes d’essai permettant de déterminer la résistance de l’élément de fond des boîtes d’inspection et de branchement et des regards thermoplastiques par rapport à la pression externe du sol et de l’eau souterraine après installation.
Cevni sistemi iz polimernih materialov za odpadno vodo in kanalizacijo, ki delujejo po težnostnem principu in so položeni v zemljo - Plastomerni revizijski in vstopni jaški - Metode preskušanja odpornosti proti uklonu (ISO 13267:2022)
Ta dokument določa metode preskušanja odpornosti dna termoplastnih revizijskih jaškov in vstopnih jaškov na pritisk, ki ga povzroča zunanja zemlja in podtalnica po vgradnji.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-april-2023
Nadomešča:
SIST EN 14830:2007
Cevni sistemi iz polimernih materialov za odpadno vodo in kanalizacijo, ki delujejo
po težnostnem principu in so položeni v zemljo - Plastomerni revizijski in vstopni
jaški - Metode preskušanja odpornosti proti uklonu (ISO 13267:2022)
Thermoplastics piping systems for non-pressure underground drainage and sewerage -
Thermoplastics inspection chamber and manhole bases - Test methods for buckling
resistance (ISO 13267:2022)
Kunststoff-Rohrleitungssysteme aus Thermoplasten für erdverlegte drucklose
Abwasserkanäle und -leitungen - Böden von Kontroll- und Einsteigschächten aus
Thermoplasten - Prüfverfahren für die Widerstandsfähigkeit gegen Einbeulen (ISO
13267:2022)
Systèmes de canalisations thermoplastiques pour branchements et collecteurs
d'assainissement enterrés sans pression - Éléments de fond de boîtes d'inspection et de
branchement et de regards thermoplastiques - Méthode d'essai de résistance au
flambage (ISO 13267:2022)
Ta slovenski standard je istoveten z: EN ISO 13267:2023
ICS:
23.040.20 Cevi iz polimernih materialov Plastics pipes
91.140.80 Drenažni sistemi Drainage systems
93.030 Zunanji sistemi za odpadno External sewage systems
vodo
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EN ISO 13267
EUROPEAN STANDARD
NORME EUROPÉENNE
January 2023
EUROPÄISCHE NORM
ICS 23.040.20; 23.040.45; 91.140.80; 93.030 Supersedes EN 14830:2006
English Version
Thermoplastics piping systems for non-pressure
underground drainage and sewerage - Thermoplastics
inspection chamber and manhole bases - Test methods for
buckling resistance (ISO 13267:2022)
Systèmes de canalisations thermoplastiques pour Kunststoff-Rohrleitungssysteme aus Thermoplasten
branchements et collecteurs d'assainissement enterrés für erdverlegte drucklose Abwasserkanäle und -
sans pression - Éléments de fond de boîtes d'inspection leitungen - Böden von Kontroll- und Einsteigschächten
et de branchement et de regards thermoplastiques - aus Thermoplasten - Prüfverfahren für die
Méthode d'essai de résistance au flambage (ISO Widerstandsfähigkeit gegen Einbeulen (ISO
13267:2022) 13267:2022)
This European Standard was approved by CEN on 2 January 2023.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2023 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 13267:2023 E
worldwide for CEN national Members.
Contents Page
European foreword . 3
European foreword
The text of ISO 13267:2022 has been prepared by Technical Committee ISO/TC 138 "Plastics pipes,
fittings and valves for the transport of fluids” of the International Organization for Standardization
(ISO) and has been taken over as EN ISO 13267:2023 by Technical Committee CEN/TC 155 “Plastics
piping systems and ducting systems” the secretariat of which is held by NEN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by July 2023, and conflicting national standards shall be
withdrawn at the latest by July 2023.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 14830:2006.
Any feedback and questions on this document should be directed to the users’ national standards body.
A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and the
United Kingdom.
Endorsement notice
The text of ISO 13267:2022 has been approved by CEN as EN ISO 13267:2023 without any modification.
INTERNATIONAL ISO
STANDARD 13267
Second edition
2022-06
Thermoplastics piping systems for
non-pressure underground drainage
and sewerage — Thermoplastics
inspection chamber and manhole
bases — Test methods for buckling
resistance
Systèmes de canalisations thermoplastiques pour branchements
et collecteurs d'assainissement enterrés sans pression — Éléments
de fond de boîtes d'inspection et de branchement et de regards
thermoplastiques — Méthode d'essai de résistance au flambage
Reference number
ISO 13267:2022(E)
ISO 13267:2022(E)
© ISO 2022
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii
ISO 13267:2022(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Principle . 1
5 Apparatus . 2
6 Conditioning . 2
7 Test environment . 3
8 Procedure .3
8.1 Internal negative pressure testing using a free-standing test assembly . 3
8.2 Internal negative pressure testing using a test box . 7
8.3 External pressure testing with the assembly submerged in a water tank . 8
8.4 Evaluation . 9
9 Test report . 9
Annex A (informative) Evaluation example .11
iii
ISO 13267:2022(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to
the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see
www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 138, Plastics pipes, fittings and valves for
the transport of fluids, Subcommittee SC 1, Plastics pipes and fittings for soil, waste and drainage (including
land drainage).
This second edition cancels and replaces the first edition (ISO 13267:2010), which has been technically
revised.
The main changes are as follows:
— normative references have been updated;
— definitions have been removed;
— technical changes have been made in 8.1, including new figures;
— minor editorial changes have been made.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www.iso.org/members.html.
iv
INTERNATIONAL STANDARD ISO 13267:2022(E)
Thermoplastics piping systems for non-pressure
underground drainage and sewerage — Thermoplastics
inspection chamber and manhole bases — Test methods
for buckling resistance
1 Scope
This document specifies methods of test for the resistance of the base of thermoplastics inspection
chambers and manholes to external soil and ground-water pressure after installation.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
ISO 9967:2016, Thermoplastics pipes — Determination of creep ratio
CEN/TS 1046:2021, Thermoplastics piping and ducting systems — Outside the building structures for
gravity and pressurised systems — Trench installation
3 Terms and definitions
No terms and definitions are listed in this document.
ISO and IEC maintain terminology databases for use in standardization at the following addresses:
— ISO Online browsing platform: available at https:// www .iso .org/ obp
— IEC Electropedia: available at https:// www .electropedia .org/
4 Principle
A sealed test assembly, comprising an inspection chamber or manhole base with a minimum height of
300 mm above the top of the main channel, is placed free standing, or bur
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.