EN ISO 3459:2022

Plastic piping systems - Mechanical joints between fittings and pressure pipes - Test method for leaktightness under negative pressure (ISO 3459:2022)

This document specifies two methods of testing for checking the leaktightness of assembled joints between mechanical fittings and plastic pressure pipes with diameters up to and including 63 mm. The test applies regardless of the design and material of the fitting used for jointing plastics pipe.
This test method is not applicable to fusion-welded joints.

Kunststoff-Rohrleitungssysteme - Mechanische Verbindungen zwischen Formstücken und Druckrohren - Prüfung der Dichtheit bei Unterdruck (ISO 3459:2022)

Dieses Dokument legt zwei Prüfverfahren zur Prüfung der Dichtheit von montierten Verbindungen zwischen mechanischen Formstücken und Kunststoffdruckrohren mit einem Durchmesser bis einschließlich 63 mm fest. Die Prüfung ist anwendbar unabhängig von Konstruktion und Werkstoff des Formstückes, das zum Verbinden von Kunststoffrohren verwendet wird.
Dieses Prüfverfahren ist nicht für Schmelzschweißverbindungen anwendbar.

Systèmes de canalisations en matières plastiques - Assemblages mécaniques entre raccords et tubes sous pression - Méthode d'essai pour l'étanchéité sous pression négative (ISO 3459:2022)

Le présent document spécifie deux méthodes d’essai pour la vérification de l’étanchéité des assemblages entre raccords mécaniques et tubes sous pression en plastique dont le diamètre est inférieur ou égal à 63 mm. L’essai s’applique quelles que soient la conception et la matière du raccord utilisé pour le raccordement du tube plastique.
La présente méthode d’essai n’est pas applicable aux assemblages soudés par fusion.

Cevni sistemi iz polimernih materialov - Mehanski spoji med fitingi in tlačnimi cevmi - Metoda za preskus tesnjenja spojev, obremenjenih s podtlakom (ISO 3459:2022)

Ta dokument določa dve metodi preskušanja za preverjanje tesnjenja sestavljenih spojev med mehanskimi fitingi in plastičnimi tlačnimi cevmi s premerom do vključno 63 mm. Preskus velja ne glede na zasnovo in material fitinga, ki se uporablja za spajanje plastičnih cevi. Ta preskusna metoda se ne uporablja za talilno zvarjene spoje.

General Information

• Status: Published
• Publication Date: 12-Apr-2022
• Withdrawal Date: 30-Oct-2022
• ICS: 23.040.60 - Flanges, couplings and joints
• Technical Committee: CEN/TC 155 - Plastics piping systems and ducting systems
• Drafting Committee: CEN/TC 155 - Plastics piping systems and ducting systems
• Current Stage: 6060 - Definitive text made available (DAV) - Publishing
• Start Date: 13-Apr-2022
• Completion Date: 13-Apr-2022
• Ref Project: SIST EN ISO 3459:2022 - Plastic piping systems - Mechanical joints between fittings and pressure pipes - Test method for leaktightness under negative pressure (ISO 3459:2022)

Relations

• Replaces: EN ISO 3459:2015 - Plastic piping systems - Mechanical joints between fittings and pressure pipes - Test method for leaktightness under negative pressure (ISO 3459:2015)
• Effective Date: 20-Apr-2022

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 3459:2022
01-junij-2022
Nadomešča:
SIST EN ISO 3459:2015
Cevni sistemi iz polimernih materialov - Mehanski spoji med fitingi in tlačnimi
cevmi - Metoda za preskus tesnjenja spojev, obremenjenih s podtlakom (ISO
3459:2022)
Plastic piping systems - Mechanical joints between fittings and pressure pipes - Test
method for leaktightness under negative pressure (ISO 3459:2022)
Kunststoff-Rohrleitungssysteme - Mechanische Verbindungen zwischen Formstücken
und Druckrohren - Prüfung der Dichtheit bei Unterdruck (ISO 3459:2022)
Systèmes de canalisations en matières plastiques - Assemblages mécaniques entre
raccords et tubes sous pression - Méthode d'essai pour l'étanchéité sous pression
négative (ISO 3459:2022)
Ta slovenski standard je istoveten z: EN ISO 3459:2022
ICS:
23.040.60 Prirobnice, oglavki in spojni Flanges, couplings and joints
elementi
SIST EN ISO 3459:2022 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN ISO 3459:2022

---------------------- Page: 2 ----------------------
SIST EN ISO 3459:2022


EN ISO 3459
EUROPEAN STANDARD

NORME EUROPÉENNE

April 2022
EUROPÄISCHE NORM
ICS 23.040.60 Supersedes EN ISO 3459:2015
English Version

Plastic piping systems - Mechanical joints between fittings
and pressure pipes - Test method for leaktightness under
negative pressure (ISO 3459:2022)
Systèmes de canalisations en matières plastiques - Kunststoff-Rohrleitungssysteme - Mechanische
Assemblages mécaniques entre raccords et tubes sous Verbindungen zwischen Formstücken und
pression - Méthode d'essai pour l'étanchéité sous Druckrohren - Prüfung der Dichtheit bei Unterdruck
pression négative (ISO 3459:2022) (ISO 3459:2022)
This European Standard was approved by CEN on 27 March 2022.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2022 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 3459:2022 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
SIST EN ISO 3459:2022
EN ISO 3459:2022 (E)
Contents Page
European foreword . 3

2

---------------------- Page: 4 ----------------------
SIST EN ISO 3459:2022
EN ISO 3459:2022 (E)
European foreword
This document (EN ISO 3459:2022) has been prepared by Technical Committee ISO/TC 138 "Plastics
pipes, fittings and valves for the transport of fluids" in collaboration with Technical Committee CEN/TC
155 “Plastics piping systems and ducting systems” the secretariat of which is held by NEN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by October 2022, and conflicting national standards shall
be withdrawn at the latest by October 2022.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 3459:2015.
Any feedback and questions on this document should be directed to the users’ national standards
body/national committee. A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, I
...