EN 2002-005:2007

Aerospace series - Test methods for metallic materials - Part 005: Uninterrupted creep and stress-rupture testing

This standard applies to uninterrupted constant-load tensile creep strain and stress-rupture testing of metallic materials governed by aerospace standards. It defines the properties that may need to be determined and the terms used in describing tests and test pieces. It specifies the dimensions of test pieces and the method of testing. The duration of the creep strain and stress-rupture tests complying with this standard shall be less than 10 000 h and at temperatures not exceeding 1 100 °C.
This standard may also apply to metallic materials for test durations exceeding 10 000 h and/or for test temperatures exceeding 1 100 °C providing that previous agreement has been reached between the manufacturer and the purchaser.

Luft- und Raumfahrt - Prüfverfahren für metallische Werkstoffe - Teil 005: Kriech- und Zeitstandversuch unter konstanter Zugbeanspruchung

Diese Norm gilt für den nicht unterbrochenen Kriech  und Zeitstandversuch unter konstanter Zugbeanspru¬chung an metallischen Werkstoffen nach Normen der Luft  und Raumfahrt. Sie definiert die gegebenenfalls zu bestimmenden Eigenschaften sowie die zur Beschreibung der Prüfungen und Proben benutzten Begriffe. Sie legt die Maße der Proben und das Prüfverfahren fest. Die Dauer des Kriech  und Zeitstandsversuchs nach dieser Norm ist auf 10 000 h bei einer maximalen Temperatur von 1 100 °C begrenzt.
Diese Norm kann auch auf metallische Werkstoffe mit einer Prüfdauer über 10 000 h und/oder Prüftempera¬turen über 1 100 °C angewendet werden, wenn dies vorher zwischen Hersteller und Käufer vereinbart wurde.

Série aérospatiale - Méthodes d'essais applicables aux matériaux métalliques - Partie 005 : Essai non interrompu de fluage et essai de rupture par fluage

Aeronavtika - Preskusne metode za kovinske materiale - 005. del: Preskusi lezenja in loma pod stalno natezno obremenitvijo

General Information

• Status: Published
• Publication Date: 13-Nov-2007
• Withdrawal Date: 30-May-2008
• ICS: 49.025.10 - Steels
• Technical Committee: ASD-STAN - Aerospace
• Drafting Committee: ASD-STAN/D 4 - Metallic
• Current Stage: 6060 - Definitive text made available (DAV) - Publishing
• Start Date: 14-Nov-2007
• Completion Date: 14-Nov-2007
• Ref Project: SIST EN 2002-005:2009 - Aerospace series - Test methods for metallic materials - Part 005: Uninterrupted creep and stress-rupture testing

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Aeronavtika - Preskusne metode za kovinske materiale - 005. del: Preskusi lezenja in loma pod stalno natezno obremenitvijoLuft- und Raumfahrt - Prüfverfahren für metallische Werkstoffe - Teil 005: Kriech- und Zeitstandversuch unter konstanter ZugbeanspruchungSérie aérospatiale - Méthodes d'essais applicables aux matériaux métalliques - Partie 005 : Essai non interrompu de fluage et essai de rupture par fluageAerospace series - Test methods for metallic materials - Part 005: Uninterrupted creep and stress-rupture testing49.025.15Neželezove zlitine na splošnoNon-ferrous alloys in general49.025.05Železove zlitine na splošnoFerrous alloys in generalICS:Ta slovenski standard je istoveten z:EN 2002-005:2007SIST EN 2002-005:2009en,de01-september-2009SIST EN 2002-005:2009SLOVENSKI
STANDARD



SIST EN 2002-005:2009



EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 2002-005November 2007ICS 49.025.10 English VersionAerospace series - Test methods for metallic materials - Part005: Uninterrupted creep and stress-rupture testingSérie aérospatiale - Méthodes d'essais applicables auxmatériaux métalliques - Partie 005 : Essai non interrompude fluage et essai de rupture par fluageLuft- und Raumfahrt - Prüfverfahren für metallischeWerkstoffe - Teil 005: Kriech- und Zeitstandversuch unterkonstanter ZugbeanspruchungThis European Standard was approved by CEN on 23 June 2007.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2007 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 2002-005:2007: ESIST EN 2002-005:2009



EN 2002-005:2007 (E) 2 Contents Page Foreword.3 1 Scope.4 2 Normative references.4 3 Principle.4 4 Terms and definitions.4 5 Symbols and abbreviations.7 6 Specification of test requirements.9 7 Testing equipment.9 8 Proportional test pieces.11 9 Non-proportional test pieces.13 10 Preparation of test piece from sample.13 11 Measurement of cross-sectional area.14 12 Marking the original gauge length.14 13 Heating of test piece.14 14 Temperature control and observations.
...