EN 12230:2003
(Main)Surfaces for sports areas - Determination of tensile properties of synthetic sports surfaces
Surfaces for sports areas - Determination of tensile properties of synthetic sports surfaces
This European Standard specifies a method for the determination of the tensile properties of materials used as surfaces for sports areas. It is applicable to elastomeric materials which are used as the upper wearing layer of such areas, and to elastomeric materials used as underlayers in composite sports surfacing systems. It is applicable both to prefabricated sheet materials and to materials formed by casting of liquid systems cured in-situ.
Sportböden - Bestimmung der Zugfestigkeitseigenschaften von Kunststoffflächen
Die Europäische Norm legt ein Verfahren für die Bestimmung der Zugfestigkeitseigenschaften von Materialien fest, die als Sportböden eingesetzt werden. Sie gilt für elastomere Materialien, die als obere Tragschicht solcher Flächen und als untere Tragschicht im Verbundsystem verwendet werden. Sie gilt sowohl für vorgefertigte Bahnen als auch für Materialien, die am Bau eingebracht werden.
ANMERKUNG Falls die Art des Sportbodens so ist, dass ein repräsentativer Probekörper nicht nach dieser Norm hergestellt werden kann, so sollte die Bestimmung der Zugeigenschaften nicht zum Zwecke der Qualitätsüberwachung oder als Voraussage für die Gebrauchstauglichkeit verwendet werden. Bei solchen Materialien kann es geeigneter sein, für diese Zwecke die Druckfestigkeit oder andere dynamische Eigenschaften zu bestimmen.
Sols sportifs - Détermination des caractéristiques de traction des surfaces sportives synthétiques
La présente Norme européenne fixe une méthode de détermination des caractéristiques de traction des matériaux utilisés dans la fabrication des surfaces de terrains de sport. Elle s'applique aux matériaux élastomères utilisés comme couche supérieure de résistance à l'usure de ces sols ou comme sous-couches dans les systèmes de surfaces composites. Elle s'applique à la fois aux matériaux en couches préfabriquées et aux matériaux moulés par coulage de systèmes liquides polymérisés sur site.
NOTE Si la nature de la surface sportive ne permet pas de préparer d'éprouvette réellement représentative suivant le mode opératoire décrit dans la présente Norme, il convient de ne pas envisager de déterminer les caractéristiques de traction aux fins d'un contrôle de la qualité, ni pour prévoir les performances à l'utilisation. Dans le cas de tels matériaux, il peut se révéler plus approprié, dans cette optique, de déterminer les caractéristiques de compression ou toute autre caractéristique dynamique.
Podloge za športne dejavnosti – Ugotavljanje nateznih lastnosti športnih podlog iz umetnih snovi
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Podloge za športne dejavnosti – Ugotavljanje nateznih lastnosti športnih podlog iz umetnih snoviSportböden - Bestimmung der Zugfestigkeitseigenschaften von KunststoffflächenSols sportifs - Détermination des caractéristiques de traction des surfaces sportives synthétiquesSurfaces for sports areas - Determination of tensile properties of synthetic sports surfaces97.220.10Športni objektiSports facilitiesICS:Ta slovenski standard je istoveten z:EN 12230:2003SIST EN 12230:2003en01-julij-2003SIST EN 12230:2003SLOVENSKI
STANDARD
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 12230April 2003ICS 97.220.10English versionSurfaces for sports areas - Determination of tensile properties ofsynthetic sports surfacesSols sportifs - Détermination des caractéristiques detraction des surfaces sportives synthétiquesSportböden - Bestimmung der Zugfestigkeitseigenschaftenvon KunststoffflähenThis European Standard was approved by CEN on 12 December 2002.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,Hungary, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Slovakia, Spain, Sweden, Switzerland and UnitedKingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2003 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 12230:2003 ESIST EN 12230:2003
If the nature of the sports surface is such that a properly representative test piece cannot be prepared in the mannerdescribed in this standard, then determination of tensile properties should not be attempted for quality control purposes, or as apredictor of performance in use. With such materials, it might be more appropriate to determine their compressive properties orother dynamic characteristics for these purposes.2 Normative referencesThis European Standard incorporates by dated or undated reference, provisions from other publications. Thesenormative references are cited at the appropriate places in the text, and the publications are listed hereafter. Fordated references, subsequent amendments to or revisions of any of these publications apply to this EuropeanStandard only when incorporated in it by amendment or revision. For undated references the latest edition of thepublication referred to applies (including amendments).ISO 291, Plastics — Standard atmospheres for conditioning and testing.3 Term and definitionFor the purposes of this European Standard, the following term and definition applies.3.1peak to valley heightgeometric measure of the roughness of the top of the surfacing, being the magnitude of regularly or irregularlyrecurring vertical deviations of a surface from a reference surface, when the distances between these deviations isa low multiple of their depth4
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.