EN ISO 11997-1:2017
(Main)Paints and varnishes - Determination of resistance to cyclic corrosion conditions - Part 1: Wet (salt fog)/dry/humid (ISO 11997-1:2017)
Paints and varnishes - Determination of resistance to cyclic corrosion conditions - Part 1: Wet (salt fog)/dry/humid (ISO 11997-1:2017)
ISO 11997-1:2017 specifies a method for the determination of the resistance of coatings to one of four defined cycles of wet (salt fog)/dry/humid conditions using specified solutions.
Beschichtungsstoffe - Bestimmung der Beständigkeit bei zyklischen Korrosionsbedingungen - Teil 1: Nass (Salzsprühnebel)/trocken/feucht (ISO 11997-1:2017)
Dieser Teil von ISO 11997 legt ein Verfahren zum Bestimmen der Beständigkeit von Beschichtungen gegen einen von vier festgelegten Zyklen bei Bedingungen, die Nässe (Salz¬sprüh¬nebel)/Trockenheit/Feuchte umfassen, fest. Dabei werden festgelegte Lösungen verwendet.
Peintures et vernis - Détermination de la résistance aux conditions de corrosion cyclique - Partie 1: Brouillard salin/sécheresse/humidité (ISO 11997-1:2017)
ISO 11997-1:2017 spécifie une méthode pour la détermination de la résistance des revêtements à l'un des quatre cycles définis brouillard salin/sécheresse/humidité, au moyen de solutions spécifiques.
Barve in laki - Ugotavljanje odpornosti proti cikličnim korozijskim pogojem - 1. del: Mokro (slana megla)/suho/vlažno (ISO 11997-1:2017)
Ta dokument določa metodo za ugotavljanje odpornosti prevlek proti enemu od štirih
opredeljenih cikličnih mokrih (slana megla)/suhih/vlažnih pogojev s podanimi rešitvami.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-december-2017
1DGRPHãþD
SIST EN ISO 11997-1:2006
%DUYHLQODNL8JRWDYOMDQMHRGSRUQRVWLSURWLFLNOLþQLPNRUR]LMVNLPSRJRMHPGHO
0RNUR VODQDPHJOD VXKRYODåQR ,62
Paints and varnishes - Determination of resistance to cyclic corrosion conditions - Part 1:
Wet (salt fog)/dry/humid (ISO 11997-1:2017)
Beschichtungsstoffe - Bestimmung der Beständigkeit bei zyklischen
Korrosionsbedingungen - Teil 1: Nass (Salzsprühnebel)/trocken/Feuchte (ISO 11997-
1:2017)
Peintures et vernis - Détermination de la résistance aux conditions de corrosion cyclique
- Partie 1: Brouillard salin/sécheresse/humidité (ISO 11997-1:2017)
Ta slovenski standard je istoveten z: EN ISO 11997-1:2017
ICS:
87.040 Barve in laki Paints and varnishes
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EN ISO 11997-1
EUROPEAN STANDARD
NORME EUROPÉENNE
September 2017
EUROPÄISCHE NORM
ICS 87.040 Supersedes EN ISO 11997-1:2006
English Version
Paints and varnishes - Determination of resistance to
cyclic corrosion conditions - Part 1: Wet (salt
fog)/dry/humid (ISO 11997-1:2017)
Peintures et vernis - Détermination de la résistance Beschichtungsstoffe - Bestimmung der Beständigkeit
aux conditions de corrosion cyclique - Partie 1: bei zyklischen Korrosionsbedingungen - Teil 1: Nass
Brouillard salin/sécheresse/humidité (ISO 11997- (Salzsprühnebel)/trocken/Feuchte (ISO 11997-
1:2017) 1:2017)
This European Standard was approved by CEN on 12 July 2017.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2017 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 11997-1:2017 E
worldwide for CEN national Members.
Contents Page
European foreword . 3
European foreword
This document (EN ISO 11997-1:2017) has been prepared by Technical Committee ISO/TC 35 “Paints
and varnishes” in collaboration with Technical Committee CEN/TC 139 “Paints and varnishes” the
secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by March 2018, and conflicting national standards shall
be withdrawn at the latest by March 2018.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 11997-1:2006.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The text of ISO 11997-1:2017 has been approved by CEN as EN ISO 11997-1:2017 without any
modification.
INTERNATIONAL ISO
STANDARD 11997-1
Third edition
2017-08
Paints and varnishes — Determination
of resistance to cyclic corrosion
conditions —
Part 1:
Wet (salt fog)/dry/humid
Peintures et vernis — Détermination de la résistance aux conditions
de corrosion cyclique —
Partie 1: Brouillard salin/sécheresse/humidité
Reference number
ISO 11997-1:2017(E)
©
ISO 2017
ISO 11997-1:2017(E)
© ISO 2017, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2017 – All rights reserved
ISO 11997-1:2017(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 2
4 Principle . 2
5 Salt fog test solution . 2
6 Apparatus . 2
7 Sampling . 4
8 Test panels . 4
8.1 Material and dimensions . 4
8.2 Preparation and coating of panels . 4
8.3 Drying and conditioning . 4
8.4 Thickness of coating . 4
8.5 Preparation of scribe . 4
9 Method of exposure of test panels . 5
10 Operating conditions . 5
11 Procedure. 5
12 Examination of test panels . 5
13 Precision . 6
14 Test report . 6
Annex A (normative) Cycle A . 8
Annex B (normative) Cycle B . 9
Annex C (normative) Cycle C .10
Annex D (normative) Cycle D .12
Annex E (informative) Factors to be considered in the design and construction of salt
spray cabinets .13
Bibliography .14
ISO 11997-1:2017(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/ patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO’s adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following
URL: w w w . i s o .org/ iso/ foreword .html.
This document was prepared by Technical Committee ISO/TC 35, Paints and varnishes, Subcommittee
SC 9, General test methods for paints and varnishes.
This third edition cancels and replaces the second edition (ISO 11997-1:2005), which has been
technically revised.
The main changes compared to the previous edition are as follows:
— the time for no drops of moisture are visible on the panels (see 6.4) has been changed;
— a reference to ISO 4628-8 for assessment of degree of delamination and corrosion around a scribe
or other artificial defect has been added;
— a reference to ISO 4620-10 for assessment of
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.