prEN 853
(Main)Rubber hoses and hose assemblies - Wire braid reinforced hydraulic type - Specification
Rubber hoses and hose assemblies - Wire braid reinforced hydraulic type - Specification
This document specifies requirements for four types of wire braid reinforced hoses and hose assemblies of nominal bore from 5 to 76: Types 1SN, 2SN, 1ST and 2ST. They are suitable for use with:
- hydraulic fluids in accordance with ISO 6743 4 with the exception of HFD R, HFD S and HFD T at temperatures ranging from −40 °C to +100 °C;
- water based fluids at temperatures ranging from −40 °C to +70 °C;
- water at temperatures ranging from 0 °C to +70 °C.
The hoses are not suitable for use with castor oil based and ester-based fluids.
This document does not include requirements for end fittings. It is limited to the performance of hoses and hose assemblies.
NOTE Requirements for hydraulic hoses for underground mining are covered in other documents.
Gummischläuche und ‑schlauchleitungen - Hydraulikschläuche mit Drahtgeflechteinlage - Spezifikation
Dieses Dokument legt Anforderungen für vier Typen von Schläuchen und Schlauchleitungen mit Drahtgeflechteinlagen vom Nenndurchmesser 5 bis 76 fest: Typ 1SN, Typ 2SN, Typ 1ST und Typ 2ST. Sie sind geeignet zur Verwendung mit:
- Hydraulikflüssigkeiten nach ISO 6743 4 mit Ausnahme von HFD R, HFD S und HFD T in einem Temperaturbereich von −40 °C bis +100 °C;
- wässrigen Flüssigkeiten in einem Temperaturbereich von −40 °C bis +70 °C;
- Wasser in einem Temperaturbereich von 0 °C bis +70 °C.
Die Schläuche sind für Flüssigkeiten auf Rizinusöl- oder Esterbasis nicht geeignet.
Dieses Dokument enthält keine Anforderungen an die Endarmaturen. Es beschränkt sich auf die Leistungsfähigkeit der Schläuche und Schlauchleitungen.
ANMERKUNG Anforderungen an Hydraulikschläuche für den untertägigen Bergbau werden in anderen Dokumenten behandelt.
Tuyaux et flexibles en caoutchouc - Type hydraulique avec armature de fils métalliques tressés - Spécification
Le présent document spécifie les exigences pour quatre types de tuyaux et assemblages flexibles à armature tressée de fils métalliques, d’alésage nominal de 5 à 76 : Types 1SN, 2SN, 1ST et 2ST. Ils sont destinés à être utilisés avec :
- les fluides hydrauliques conformes à l'ISO 6743-4, à l'exception des HFD R, HFD S et HFD T, et dans une plage de températures de −40 °C à +100 °C ;
- les fluides aqueux dans une plage de températures de −40 °C à +70 °C ;
- l'eau dans une plage de températures de 0 °C à +70 °C.
Les tuyaux ne conviennent pas pour des utilisations avec des fluides à base d'huile de ricin ou d'ester.
Le présent document ne contient pas d'exigences relatives aux extrémités de raccordement. Il se limite aux performances des tuyaux et assemblages flexibles.
NOTE Les exigences pour les tuyaux hydrauliques pour mines souterraines font l'objet d'un autre document.
Gumene cevi in cevni priključki - Z jeklenim kordom ojačene hidravlične cevi - Specifikacija
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-december-2024
Gumene cevi in cevni priključki - Z jeklenim kordom ojačene hidravlične cevi -
Specifikacija
Rubber hoses and hose assemblies - Wire braid reinforced hydraulic type - Specification
Gummischläuche und -schlauchleitungen - Hydraulikschläuche mit Drahtgeflechteinlage
- Spezifikation
Tuyaux et flexibles en caoutchouc - Type hydraulique avec armature de fils métalliques
tressés - Spécification
Ta slovenski standard je istoveten z: prEN 853
ICS:
23.040.70 Gumene cevi in armature Hoses and hose assemblies
23.100.40 Cevna napeljava in sklopke Piping and couplings
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
DRAFT
EUROPEAN STANDARD
NORME EUROPÉENNE
EUROPÄISCHE NORM
October 2024
ICS 23.040.70 Will supersede EN 853:2015
English Version
Rubber hoses and hose assemblies - Wire braid reinforced
hydraulic type - Specification
Tuyaux et flexibles en caoutchouc - Type hydraulique Gummischläuche und -schlauchleitungen -
avec armature de fils métalliques tressés - Spécification Hydraulikschläuche mit Drahtgeflechteinlage -
Spezifikation
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee
CEN/TC 218.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations
which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2024 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 853:2024 E
worldwide for CEN national Members.
Contents Page
European foreword . 3
1 Scope . 4
2 Normative references . 4
3 Terms and definitions . 4
4 Types of hoses . 5
5 Materials and construction . 5
5.1 Hoses . 5
5.2 Hose assemblies . 5
6 Dimensions. 5
6.1 Diameters and concentricity . 5
6.2 Length. 7
6.2.1 Hoses . 7
6.2.2 Hose assemblies . 7
7 Requirements . 8
7.1 Hydrostatic requirements . 8
7.2 Minimum bend radius . 9
7.3 Impulse test requirements . 10
7.4 Leakage of hose assemblies . 10
7.5 Cold flexibility . 10
7.6 Adhesion between components . 11
7.7 Vacuum resistance . 11
7.8 Abrasion resistance . 11
7.9 Fluid resistance . 12
7.9.1 Test pieces . 12
7.9.2 Oil resistance . 12
7.9.3 Water based fluid resistance . 12
7.9.4 Water resistance . 12
7.10 Ozone resistance . 12
8 Designation . 12
9 Frequency of testing . 12
10 Marking . 13
10.1 Hoses . 13
10.2 Hose assemblies . 13
Annex A (normative) Test frequency for type tests and routine tests . 14
Bibliography . 16
European foreword
This document (prEN 853:2024) has been prepared by Technical Committee CEN/TC 218 “Rubber and
plastics hoses and hose assemblies”, the secretariat of which is held by BSI.
This document is currently submitted to the CEN Enquiry.
This document will supersede EN 853:2015.
This document includes the following significant technical changes with respect to EN 853:2015:
— scope changed (nominal bore extended: 5 to 76);
— EN 853, 854, 856 and 857 have been aligned;
— updated normative references;
— Table 7 added;
— Annex A deleted;
— Annex C deleted.
1 Scope
This document specifies requirements for four types of wire braid reinforced hoses and hose assemblies
of nominal bore from 5 to 76: Types 1SN, 2SN, 1ST and 2ST. They are suitable for use with:
— hydraulic fluids in accordance with ISO 6743-4 with the exception of HFD R, HFD S and HFD T at
temperatures ranging from −40 °C to +100 °C;
— water based fluids at temperatures ranging from −40 °C to +70 °C;
— water at temperatures ranging from 0 °C to +70 °C.
The hoses are not suitable for use with castor oil based and ester-based fluids.
This document does not include requirements for end fittings. It is limited to the performance of hoses
and hose assemblies.
NOTE Requirements for hydraulic hoses for underground mining are covered in other documents.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
EN ISO 1402, Rubber and plastics hoses and hose assemblies — Hydrostatic testing (ISO 1402)
EN ISO 4671, Rubber and plastics hoses and hose assemblies — Methods of measurement of the dimensions
of hoses and the lengths of hose assemblies (ISO 4671)
EN ISO 6803, Rubber or plastics hoses and hose assemblies — Hydraulic-pressure impulse test without
flexing (ISO 6803)
EN ISO 7233, Rubber and plastics hoses and hose assemblies — Determination of resistance to vacuum
(ISO 7233)
EN ISO 7326:2016, Rubber and plastics hoses — Assessment of ozone resistance under static conditions
(ISO 7326:2016)
EN ISO 8033, Rubber and plastics hoses — Determination of adhesion between components (ISO 8033)
EN ISO 10619-2:2021, Rubber and plastics hoses and tubing — Measurement of flexibility and stiffness —
Part 2: Bending tests at sub-ambient temperatures (ISO 10619-2:2021)
ISO 1817:2024, Rubber, vulcanized or thermoplastic — Determination of the effect of liquids
ISO/TS 20444, Rubber and plastics hoses — Determination of abrasion resistance of the outer cover
3 Terms and definitions
No terms and definitions are listed in this document.
ISO and IEC maintain terminology databases for use in standardization at the following addresses:
Under preparation. Stage at time of preparation: ISO/DTS 20444
— ISO Online browsing platform: available at https://www.iso.org/obp
— IEC Electropedia: available at https://www.electropedia.org/
4 Types of hoses
Four types of hoses are specified, distinguished by their construction and maximum working pressure:
1) Type 1ST – hoses with a single braid of wire reinforcement;
2) Type 2ST – hoses with two braids of wire reinforcement;
3) Type 1SN – hoses with a single braid of wire reinforcement;
4) Type 2SN – hoses with two braids of wire reinforcement.
Types 1SN and 2SN shall be of the same reinforcement construction as types 1ST and 2ST, except that
they shall have thinner covers designed to assemble with fittings that do not require removal of the cover
or a portion of the cover.
For new designs of braided hoses in hydraulic fluid power applications hose types 1SN and 2SN, specified
in this document, and 1SC and 2SC, specified in EN 857, shall be used. Hose types 1ST and 2ST shall not
be used for new designs in hydraulic fluid power applications.
Hoses and hose assemblies shall not be operated outside the limits of this document.
5 Materials and construction
5.1 Hoses
Hoses shall consist of an oil and water resistant synthetic rubber lining, one or two layers of high tensile
steel wire and an oil and weather resistant rubber cover. Each wire ply shall be separated by an insulating
layer of synthetic rubber.
5.2 Hose assemblies
Hose assemblies shall only be manufactured with those hose fittings whose functionality as a defined
hose and fitting combination has been verified in accordance with 7.1, 7.3, 7.4 and 7.5 of this document.
The manufacturer’s instructions shall be followed for the preparation and fabrication of hose assemblies.
6 Dimensions
6.1 Diameters and concentricity
The diameters of the hoses shall be measured in accordance with EN ISO 4671 and as such shall conform
to the values in Table 1.
Table 1 — Diameters of hoses
Dimensions in millimetres except nominal bore
All types Type 1ST Type 1SN Type 2ST Type 2SN
Outside Outside Outside Outside
Nominal Inside Diameter over Cover Diameter over Cover
diameter of diameter diameter of diameter
bore diameter reinforcement thickness reinforcement thickness
hose of hose hose of hose
min. max. min. max. min. max. max. min. max. min. max. min. max. max. min. max.
5 4,9 5,4 9,0 10,0 11,9 13,5 12,5 0,8 1,5 10,6 11,6 15,1 16,7 14,1 0,8 1,5
6 6,4 7,0 10,6 11,6 15,1 16,7 14,1 0,8 1,5 12,1 13,3 16,7 18,3 15,7 0,8 1,5
8 7,9 8,
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.