23.040.70 - Hoses and hose assemblies
Hoses and hose assemblies
Schlauche. Schlaucharmaturen
Tuyaux et flexibles
Gumene cevi in armature
General Information
This document specifies electrical test methods for rubber and plastics hoses, tubing and hose
assemblies to determine the resistance of conductive, antistatic and non-conductive hoses and the
electrical continuity or discontinuity between metal end fittings.
All the test methods described for rubber hoses in this document can also be applied to plastics hoses.
- Standard24 pagesEnglish language
sale 10% off- e-Library read for1 day
- Draft21 pagesEnglish language
sale 10% off- e-Library read for1 day
This document specifies electrical test methods for rubber and plastics hoses, tubing and hose assemblies to determine the resistance of conductive, antistatic and non-conductive hoses and the electrical continuity or discontinuity between metal end fittings. All the test methods described for rubber hoses in this document can also be applied to plastics hoses.
- Standard16 pagesEnglish language
sale 15% off- Standard16 pagesFrench language
sale 15% off- Draft16 pagesEnglish language
sale 15% off
EN 16436-1+A3 specifies the characteristics and performance requirements for tubing and hoses made of either rubber or plastics for use with commercial propane and commercial butane and mixtures thereof, in the vapour phase, for connection of appliances, from:- pressurized gas container to a regulating device,- pressurized gas container to an appliance,- regulating device to an appliance, and- regulating device to installation pipework,in environments of a temperature range from -30 °C to +70 °C...view more
- Standard21 pagesEnglish language
sale 10% off- e-Library read for1 day
- Standard20 pagesEnglish language
sale 10% off- e-Library read for1 day
This document specifies requirements for two types of thermoplastic multi-layer (non-vulcanized) transfer hoses and hose assemblies for carrying liquefied petroleum gas and liquefied natural gas. Each type is subdivided into two classes, one for onshore duties, and the other for offshore.
This document is applicable for hose sizes from 25 mm to 250 mm, working pressures from 10,5 bar to 25 bar and operating temperatures from - 196 °C to + 45 °C.
NOTE Offshore LNG hose assemblies are also speci...view more
- Standard23 pagesEnglish language
sale 10% off- e-Library read for1 day
This document defines current terms concerning metal hoses, metal hose assemblies and component parts. This document applies to: a) stripwound metal hoses and hose assemblies; b) corrugated metal hoses and hose assemblies. NOTE 1 These hoses can be used braided, covered or lined. NOTE 2 Equivalent terms in English, French, German and Dutch are given in Annex A.
- Standard7 pagesEnglish language
sale 15% off- Standard8 pagesFrench language
sale 15% off
This document establishes a system of designation for polyketone (PK) moulding and extrusion materials which may be used as the basis for specifications. Polyketone polymer chains are built up from regularly alternating olefinic units and keto groups. The olefinic units shall be randomly distributed ethylene and propylene. The types of polyketone plastics are differentiated from each other by a classification system based on appropriate levels of the designatory properties, melting temperature, ...view more
- Standard11 pagesEnglish language
sale 10% off- e-Library read for1 day
- Draft8 pagesEnglish language
sale 10% off- e-Library read for1 day
This document specifies the requirements for three types of general-purpose textile-reinforced rubber water hose with an operating temperature range of −25 °C to +70 °C and a maximum working pressure of up to 2,5 MPa (25 bar).
These hoses are not intended to be used for conveyance of potable (drinking) water, for washing-machine inlets, as firefighting hoses, for special agricultural machines or as collapsible water hoses.
These hoses can be used with additives which lower the freezing point o...view more
- Standard11 pagesEnglish language
sale 10% off- e-Library read for1 day
- Draft8 pagesEnglish language
sale 10% off- e-Library read for1 day
This document specifies the requirements for three types of general-purpose textile-reinforced rubber water hose with an operating temperature range of −25 °C to +70 °C and a maximum working pressure of up to 2,5 MPa (25 bar). These hoses are not intended to be used for conveyance of potable (drinking) water, for washing-machine inlets, as firefighting hoses, for special agricultural machines or as collapsible water hoses. These hoses can be used with additives which lower the freezing point of ...view more
- Standard4 pagesFrench language
sale 15% off- Standard4 pagesEnglish language
sale 15% off
This European Standard specifies the design, materials and dimensions of fittings for clamp type coupling assemblies for use with nominal sizes DN 15 to DN 50 steam and hot water hoses. It covers assemblies up to a maximum working pressure of 18 bar ) (corresponding to a saturated steam temperature of 210 °C).
- Standard24 pagesEnglish language
sale 10% off- e-Library read for1 day
This European Standard specifies the design, materials and dimensions of fittings for clamp type coupling assemblies for use with nominal sizes DN 15 to DN 50 steam and hot water hoses. It covers assemblies up to a maximum working pressure of 18 bar ) (corresponding to a saturated steam temperature of 210 °C).
- Standard24 pagesEnglish language
sale 10% off- e-Library read for1 day
This European Standard specifies requirements for four types of rubber-covered spiral wire reinforced hydraulic hoses and hose assemblies of nominal bore from 6 to 51: Types 4SP, 4SH, R12 and R13. They are all suitable for use with:
- hydraulic fluids in accordance with ISO 6743 4 with the exception of HFD R, HFD S and HFD T at temperatures ranging from −40 °C to +100 °C for types 4SP and 4SH and −40 °C to +120 °C for types R12 and R13;
- water based fluids at temperatures ranging from −40 °C ...view more
- Standard17 pagesEnglish language
sale 10% off- e-Library read for1 day
- Standard1 pageFrench language
sale 15% off- Standard1 pageEnglish language
sale 15% off
This European Standard specifies the requirements for rubber hoses and rubber hose assemblies used for the transfer of liquefied petroleum gas (LPG) in liquid or gaseous phase and natural gas with a maximum working pressure of 25 bar (2,5 MPa) and vacuum within the temperature range of −30 °C to +70 °C and, when designated -LT, −50 °C to +70 °C.
- Standard22 pagesEnglish language
sale 10% off- e-Library read for1 day
This draft European Standard describes and specifies the characteristics and performance requirements for assemblies made of tubing and hoses complying with EN 16436-1 to be used in the same conditions.
All connections are given in Annex B.
This draft European Standard only defines specific connections which are not defined in other standards (e.g. EN 16129).
- Standard17 pagesEnglish language
sale 10% off- e-Library read for1 day
This document describes hose impulse testing, with flexing, of rubber or plastics hydraulic hose
assemblies at both high and low impulse pressures. The high-pressure testing is carried out at pressures
greater than 3 MPa and the low-pressure testing at pressures from 1,5 MPa to 3 MPa. The test procedure
is applicable to hydraulic hose assemblies that are subject to pulsating pressures in service which are
included in the product requirements.
NOTE Impulse test procedures without flexing can...view more
- Draft11 pagesEnglish language
sale 10% off- e-Library read for1 day
- Standard15 pagesEnglish language
sale 10% off- e-Library read for1 day
- Draft9 pagesEnglish language
sale 10% off- e-Library read for1 day
This document describes hose impulse testing, with flexing, of rubber or plastics hydraulic hose assemblies at both high and low impulse pressures. The high-pressure testing is carried out at pressures greater than 3 MPa and the low-pressure testing at pressures from 1,5 MPa to 3 MPa. The test procedure is applicable to hydraulic hose assemblies that are subject to pulsating pressures in service which are included in the product requirements.
NOTE Impulse test procedures without flexing can be ...view more
- Draft11 pagesEnglish language
sale 10% off- e-Library read for1 day
- Standard15 pagesEnglish language
sale 10% off- e-Library read for1 day
- Draft9 pagesEnglish language
sale 10% off- e-Library read for1 day
This document describes hose impulse testing, with flexing, of rubber or plastics hydraulic hose assemblies at both high and low impulse pressures. The high-pressure testing is carried out at pressures greater than 3 MPa and the low-pressure testing at pressures from 1,5 MPa to 3 MPa. The test procedure is applicable to hydraulic hose assemblies that are subject to pulsating pressures in service which are included in the product requirements. NOTE Impulse test procedures without flexing can be f...view more
- Standard7 pagesFrench language
sale 15% off- Standard7 pagesEnglish language
sale 15% off
This document lays down the dimensions and specifies the characteristics of the constituent parts of hose connections for welding, cutting and allied processes, for example for pressure regulators according to EN ISO 2503 and blowpipes. The suitability of the hose connections mentioned below will be considered according to the applied pressure range. This document does not cover the design of the hose tail inserted into the hose. This is specified in EN 1256.
- Standard12 pagesEnglish language
sale 10% off- e-Library read for1 day
This document specifies requirements for four types of thermoplastic multi-layer (non-vulcanized) hoses and hose assemblies for carrying hydrocarbons, solvents and chemicals. It specifies bore sizes from 25 mm to 300 mm, working pressures from 4 bar ) to 14 bar and working temperatures from −30 °C to 150 °C.
Type 1 hoses are suitable for vapour applications. Types 2 to 4 hoses are suitable for liquid applications.
NOTE 1 The attention of users is drawn to Annex A concerning the selection of th...view more
- Draft26 pagesEnglish language
sale 10% off- e-Library read for1 day
- Standard28 pagesEnglish language
sale 10% off- e-Library read for1 day
ISO/TS 17165-2:2018 provides guidelines for selection, routing, fabrication, installation, replacement, maintenance and storage of hose and hose assemblies for hydraulic fluid power systems which are manufactured from hoses conforming to ISO 1436, ISO 3862, ISO 3949, ISO 4079 and ISO 11237, and hose fittings conforming to the ISO 12151 series. NOTE 1 Many of these practices also can be suitable for use with other types of hoses and systems. NOTE 2 Annex A lists examples of actual failure resulti...view more
- Technical specification21 pagesFrench language
sale 15% off- Technical specification20 pagesEnglish language
sale 15% off