EN ISO 6360-3:2005
(Main)Dentistry - Number coding system for rotary instruments - Part 3: Specific characteristics of burs and cutters (ISO 6360-3:2005)
Dentistry - Number coding system for rotary instruments - Part 3: Specific characteristics of burs and cutters (ISO 6360-3:2005)
ISO 6360-3:2005 specifies the code numbers for specific characteristics of burs, finishing burs, cutters and surgical instruments, which refer to the type of toothing on the working part of the instrument. This three digit number appears in the locations 10 to 12 of the 15-digit overall number and forms the fourth group of three digits in the 15-digit overall number, the principles of which are explained in ISO 6360-1 and 6360-2.
In addition to terms for rotary instruments and accessories used in two of the three official ISO languages (English, French and Russian), ISO 6360-3:2005 gives the equivalent terms in the German language; these are published under the responsibility of the member body for Germany (DIN). However, only the terms given in the official languages can be considered as ISO terms.
Zahnheilkunde - Nummernsystem für rotierende Instrumente - Teil 3: Besondere Eigenschaften von Bohrern und Fräsern (ISO 6360-3:2005)
Dieser Teil von ISO 6360 enthält Kennzahlen für die besonderen Eigenschaften der Bohrer, Finierer, Fräser und chirurgischen Instrumente, die sich auf die Verzahnungsart auf dem Arbeitsteil des Instruments beziehen. Diese dreistellige Nummer erscheint an den Stellen 10 bis 12 in der 15-stelligen Gesamtnummer und bildet die vierte Gruppe mit drei Zahlen in der 15-stelligen Gesamtnummer, deren Grundprinzipien in ISO 6360 1 und 6360 2 beschrieben werden.
ANMERKUNG Zusätzlich zu den Benennungen für rotierende Instrumente und Zubehör, die in zwei der drei offiziellen ISO-Sprachfassungen (Englisch, Französisch und Russisch) gegeben werden, enthält dieser Teil von ISO 6360 äquivalente Benennungen in der deutschen Sprache; diese erscheinen unter der Verantwortung des Mitgliedes für Deutschland (DIN). Nur die Benennungen in den offiziellen ISO-Sprachen dürfen deshalb als ISO-Benennungen angesehen werden.
Art dentaire - Système de codification numérique pour instruments rotatifs - Partie 3: Caractéristiques spécifiques des fraises et fraises de laboratoire (ISO 6360-3:2005)
L'ISO 6360-3:2005 spécifie les codes numériques des caractéristiques particulières des fraises, des fraises à finir, des fraises de laboratoire et des instruments chirurgicaux, relatifs au type de denture de la partie active de l'instrument. Ce nombre à trois chiffres apparaît aux positions 10 à 12 de l'identifiant complet à 15 chiffres et constitue le quatrième groupe de trois chiffres de cet identifiant, dont les principes sont expliqués dans l'ISO 6360-1 et l'ISO 6360-2.
En complément des termes relatifs aux instruments rotatifs et à leurs accessoires dans deux des trois langues officielles de l'ISO (anglais, français et russe), l'ISO 6360-3:2005 donne les termes équivalents en allemand; ces derniers sont publiés sous la responsabilité du comité membre d'Allemagne (DIN). Toutefois, seuls les termes donnés dans les langues officielles peuvent être considérés comme termes ISO.
Zobozdravstvo – Sistem številčnega kodiranja rotacijskih instrumentov – 3. del: Posebne lastnosti svedrov in rezil (ISO 6360-3:2005)
General Information
Standards Content (Sample)
SLOVENSKI STANDARD
01-februar-2006
=RER]GUDYVWYR±6LVWHPãWHYLOþQHJDNRGLUDQMDURWDFLMVNLKLQVWUXPHQWRY±GHO
3RVHEQHODVWQRVWLVYHGURYLQUH]LO ,62
Dentistry - Number coding system for rotary instruments - Part 3: Specific characteristics
of burs and cutters (ISO 6360-3:2005)
Zahnheilkunde - Nummernsystem für rotierende Instrumente - Teil 3: Besondere
Eigenschaften von Bohrern und Fräsern (ISO 6360-3:2005)
Art dentaire - Systeme de codification numérique pour instruments rotatifs - Partie 3:
Caractéristiques spécifiques des fraises et fraises de laboratoire (ISO 6360-3:2005)
Ta slovenski standard je istoveten z: EN ISO 6360-3:2005
ICS:
11.060.25 =RERWHKQLþQLLQVWUXPHQWL Dental instruments
35.040 Nabori znakov in kodiranje Character sets and
informacij information coding
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD
EN ISO 6360-3
NORME EUROPÉENNE
EUROPÄISCHE NORM
November 2005
ICS 11.060.25
English Version
Dentistry - Number coding system for rotary instruments - Part 3:
Specific characteristics of burs and cutters (ISO 6360-3:2005)
Art dentaire - Système de codification numérique pour Zahnheilkunde - Nummernsystem für rotierende
instruments rotatifs - Partie 3: Caractéristiques spécifiques Instrumente - Teil 3: Besondere Eigenschaften von Bohrern
des fraises et fraises de laboratoire (ISO 6360-3:2005) und Fräsern (ISO 6360-3:2005)
This European Standard was approved by CEN on 7 October 2005.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Central Secretariat or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,
Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2005 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 6360-3:2005: E
worldwide for CEN national Members.
Foreword
This document (EN ISO 6360-3:2005) has been prepared by Technical Committee ISO/TC 106
"Art dentaire" in collaboration with Technical Committee CEN/TC 55 "Dentistry", the secretariat
of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of
an identical text or by endorsement, at the latest by May 2006, and conflicting national standards
shall be withdrawn at the latest by May 2006.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of
the following countries are bound to implement this European Standard: Austria, Belgium,
Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary,
Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Endorsement notice
The text of ISO 6360-3:2005 has been approved by CEN as EN ISO 6360-3:2005 without any
modifications.
INTERNATIONAL ISO
STANDARD 6360-3
First edition
2005-11-01
Dentistry — Number coding system for
rotary instruments —
Part 3:
Specific characteristics of burs and
cutters
Art dentaire — Système de codification numérique pour instruments
rotatifs —
Partie 3: Caractéristiques spécifiques des fraises et fraises
de laboratoire
Reference number
ISO 6360-3:2005(E)
©
ISO 2005
ISO 6360-3:2005(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 2005
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2005 – All rights reserved
ISO 6360-3:2005(E)
Contents Page
Foreword. iv
Introduction . v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions. 1
4 Code numbers for specific characteristics. 2
4.1 General. 2
4.2 Type of toothing. 2
4.3 Default information. 3
5 Toothing of burs . 3
6 Toothing of finishing burs . 5
7 Toothing of cutters . 7
7.1 Cutters, very fine. 7
7.2 Cutters, fine . 8
7.3 Cutters, medium. 9
7.4 Cutters, coarse. 11
7.5 Cutters, very coarse . 12
8 Toothing of surgical instruments. 13
ISO 6360-3:2005(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 6360-3 was prepared by Technical Committee ISO/TC 106, Dentistry, Subcommittee SC 4, Dental
instruments.
ISO 6360 consists of the following parts, under the general title Dentistry — Number coding system for rotary
instruments:
⎯ Part 1: General characteristics
⎯ Part 2: Shapes
⎯ Part 3: Specific characteristics of burs and cutters
⎯ Part 4: Specific characteristics of diamond instruments
⎯ Part 6: Specific characteristics of abrasive instruments
⎯ Part 7: Specific characteristics of mandrels and special instruments
The following part is under preparation:
⎯ Part 5: Specific characteristics of root-canal instruments
iv © ISO 2005 – All rights reserved
ISO 6360-3:2005(E)
Introduction
This part of ISO 6360 is one of a series of International Standards relating to dental rotary instruments. A wide
variety of dental rotary instruments, including root-canal instruments, is manufactured throughout the world for
use by the dental profession.
ISO 6360 provides a general number coding system for all types of dental rotary instruments, including
accessories used in connection with these rotary instruments.
The benefits of this system for dentistry in its entirety will only be derived if the system is widely adopted;
manufacturers of dental instruments, as well as the dental trade, are therefore requested to refer to ISO 6360
in their catalogues.
This part of ISO 6360 was prepared in response to a need by the dental trade and industry and the dental
profession for a universal system of classification and designation for these instruments. It establishes a
comprehensive number coding system suitable for all dental rotary instruments by use of a 15-digit code
number identifying general and specific characteristics of instruments or groups of instruments.
The first group of three digits identifies the materials used for the working part of instruments.
The second group of three digits identifies the shanks and handles used for instruments and the overall
lengths of instruments.
The third group of three digits identifies the shapes of instruments.
The fourth group of three digits identifies the specific characteristics for groups of instruments.
The fifth group of three digits identifies the nominal diameter of the working part of the instruments.
The code numbers are generic code numbers. They do not provide exact product information. This
information is given in the respective product standards for dental rotary instruments.
For the application of the system and for the correct allocation of numbers or their identification it is intended
that the user consult ISO 6360-1 and ISO 6360-2 for general information, and in addition one of the
subsequent parts (ISO 6360-3 to ISO 6360-7) for further information on specific characteristics of instruments
or groups of instruments.
For the allocation of new numbers complying with ISO 6360, an application supported by a description and a
drawing should be sent to the secretariat of ISO/TC 106/SC 4, Dental instruments, which keeps updated
records of all numbers currently allocated. An international group of experts will then decide on an appropriate
identification number for the instrument in question, including its specific characteristics. The Secretary will
inform the applicant, in due course, of the result and assist him in using the number correctly. The Secretariat
of ISO/TC 106/SC 4 can be contacted at:
DIN NADENT
Alexander-Wellendorff-Str. 2
75172 Pforzheim
Germany
INTERNATIONAL STANDARD ISO 6360-3:2005(E)
Dentistry — Number coding system for rotary instruments —
Part 3:
Specific characteristics of burs and cutters
1 Scope
This part of ISO 6360 specifies the code numbers for specific characteristics of burs, finishing burs, cutters
and surgical instruments, which refer to the type of toothing on the working part of the instrument. This three
digit number appears in the locations 10 to 12 of the 15-digit overall number and forms the fourth group of
three digits in the 15-digit overall number, the principles of which are explained in ISO 6360-1 and 6360-2.
NOTE In addition to terms for rotary instruments and accessories used in two of the three official ISO languages
(English, French and R
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.