EN ISO 18563-1:2015

Non-destructive testing - Characterization and verification of ultrasonic phased array equipment - Part 1: Instruments (ISO 18563-1:2015)

ISO 18563-1:2015 identifies the functional characteristics of a multichannel ultrasonic phased array instrument used for phased array probes and provides methods for their measurement and verification.
ISO 18563-1:2015 can partly be applicable to ultrasonic phased array instruments in automated systems, but then, other tests might be needed to ensure satisfactory performance. When the phased array instrument is a part of an automated system, the acceptance criteria can be modified by agreement between the parties involved.
ISO 18563-1:2015 gives the extent of the verification and defines acceptance criteria within a frequency range of 0,5 MHz to 10 MHz.
The evaluation of these characteristics permits a well-defined description of the ultrasonic phased array instrument and comparability of instruments.

Zerstörungsfreie Prüfung - Charakterisierung und Verifizierung der Ultraschall-Prüfausrüstung mit phasengesteuerten Arrays - Teil 1: Prüfgeräte (ISO 18563-1:2015)

Essais non destructifs - Caractérisation et vérification de l'appareillage de contrôle par ultrasons en multiéléments - Partie 1: Appareils (ISO 18563-1:2015)

L'ISO 18563-1:2015 identifie les caractéristiques fonctionnelles d'un appareil à ultrasons multiélément destiné à alimenter des traducteurs multiéléments et fournit des méthodes pour les mesurer et les vérifier.
L'ISO 18563-1:2015 peut être en partie applicable aux appareils à ultrasons multiéléments présents dans les systèmes automatiques mais, dans ce cas, d'autres essais peuvent être nécessaires pour garantir des performances satisfaisantes. Lorsque l'appareil multiélément est intégré dans un système automatique, les critères d'acceptation peuvent être modifiés dans le cadre d'un accord entre les parties concernées.
L'ISO 18563-1:2015  donne l'étendue de la vérification et définit des critères d'acceptation dans une gamme de fréquences de 0,5 MHz à 10 MHz.
L'évaluation de ces caractéristiques permet de donner une description bien définie de l'appareil à ultrasons multiélément et d'assurer une comparaison entre appareils.

Neporušitvene preiskave - Ugotavljanje značilnosti in preverjanje ultrazvočne opreme faznih sistemov - 1. del: Naprave (ISO 18563-1:2015)

Ta evropski standard določa metode in kriterije sprejemljivosti za ocenjevanje električnih zmogljivosti ultrazvočnih instrumentov za delovanje ultrazvočne opreme faznih sond z osrednjimi frekvencami v razponu od 0,5 MHz do 10 MHz z uporabo pulzno-odbojnih tehnik. Ta dokument ne opisuje metod in kriterijev sprejemljivosti za opis zmogljivosti popolne ultrazvočne opreme faznih sistemov.

General Information

• Status: Withdrawn
• Publication Date: 16-Jun-2015
• Withdrawal Date: 27-Sep-2022
• ICS: 19.100 - Non-destructive testing
• Technical Committee: CEN/TC 138 - Non-destructive testing
• Drafting Committee: CEN/TC 138/WG 2 - Ultrasonic testing
• Current Stage: 9960 - Withdrawal effective - Withdrawal
• Completion Date: 28-Sep-2022
• Ref Project: SIST EN ISO 18563-1:2015 - Non-destructive testing - Characterization and verification of ultrasonic phased array systems - Part 1: Instruments (ISO 18563-1:2015)

Relations

• Replaced By: EN ISO 18563-1:2022 - Non-destructive testing - Characterization and verification of ultrasonic phased array equipment - Part 1: Instruments (ISO 18563-1:2022)
• Effective Date: 05-Oct-2022

Standards Content (Sample)

SLOVENSKI STANDARD
01-september-2015
1HSRUXãLWYHQHSUHLVNDYH8JRWDYOMDQMH]QDþLOQRVWLLQSUHYHUMDQMHXOWUD]YRþQH
RSUHPHID]QLKVLVWHPRYGHO1DSUDYH,62
Non-destructive testing - Characterization and verification of ultrasonic phased array
systems - Part 1: Instruments (ISO 18563-1:2015)
Zerstörungsfreie Prüfung - Charakterisierung und Verifizierung der Ultraschall-
Prüfausrüstung mit phasengesteuerten Arrays - Teil 1: Prüfgeräte (ISO 18563-1:2015)
Essais non destructifs - Caractérisation et vérification de l'appareillage de contrôle multi-
élément par ultrasons - Partie 1 : Instruments (ISO 18563-1:2015)
Ta slovenski standard je istoveten z: EN ISO 18563-1:2015
ICS:
19.100 Neporušitveno preskušanje Non-destructive testing
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
EN ISO 18563-1
NORME EUROPÉENNE
EUROPÄISCHE NORM
June 2015
ICS 19.100
English Version
Non-destructive testing - Characterization and verification of
ultrasonic phased array equipment - Part 1: Instruments (ISO
18563-1:2015)
Essais non destructifs - Caractérisation et vérification de Zerstörungsfreie Prüfung - Charakterisierung und
l'appareillage de contrôle par ultrasons en multiéléments - Verifizierung der Ultraschall-Prüfausrüstung mit
Partie 1: Appareils (ISO 18563-1:2015) phasengesteuerten Arrays - Teil 1: Prüfgeräte (ISO 18563-
1:2015)
This European Standard was approved by CEN on 21 February 2015.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United
Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2015 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 18563-1:2015 E
worldwide for CEN national Members.

Contents Page
European foreword .3

European foreword
This document (EN ISO 18563-1:2015) has been prepared by Technical Committee CEN/TC 138 “Non-
destructive testing” the secretariat of which is held by AFNOR, in collaboration with Technical Committee
ISO/TC 135 "Non-destructive testing".
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by December 2015, and conflicting national standards shall be withdrawn
at the latest by December 2015.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.
Endorsement notice
The text of ISO 18563-1:2015 has been approved by CEN as EN ISO 18563-1:2015 without any modification.

INTERNATIONAL ISO
STANDARD 18563-1
First edition
2015-06-15
Non-destructive testing —
Characterization and verification of
ultrasonic phased array equipment —
Part 1:
Instruments
Essais non destructifs — Caractérisation et vérification de
l’appareillage de contrôle par ultrasons en multiéléments —
Partie 1: Appareils
Reference number
ISO 18563-1:2015(E)
©
ISO 2015
ISO 18563-1:2015(E)
© ISO 2015, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. [phone]
Fax [phone]
[e-mail]
www.iso.org
ii © ISO 2015 – All rights reserved

ISO 18563-1:2015(E)
Contents Page
Foreword .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Symbols and abbreviated terms . 2
5 General requirements of conformity . 3
6 Manufacturer’s technical specification for phased array ultrasonic phased
array instruments . 3
7 Performance requirements for ultrasonic phased array instruments .7
8 Group 1 tests . 9
8.1 Equipment required for group 1 tests . 9
8.2 Battery operated phased array instruments .10
8.2.1 Operating time .10
8.2.2 Stability against voltage variations .10
8.3 Stability tests .11
8.3.1 Stability after warm-up time .11
8.3.2 Stability against temperature .11
8.4 Display .12
8.4.1 General.12
8.4.2 Time base deviation .12
8.4.3 Highest digitized frequency .12
8.4.4 Screen refresh rate for A-scan presentations .13
8.5 Transmitter .13
8.5.1 Pulse repetition frequency .13
8.5.2 Output impedance .14
8.5.3 Time delay resolution .14
8.6 Receiver .15
8.6.1 Cross-talk between receivers .15
8.6.2 Dead time after the transmitter pulse .15
8.6.3 Dynamic range and maximum input voltage.16
8.6.4 Receiver input impedance .17
8.6.5 Time-corrected gain .17
8.6.6 Temporal resolution.18
8.6.7 Time delay resolution .19
8.6.8 Linearity of vertical display over the extreme frequency ranges of
the instrument .19
8.7 Monitor gate .20
8.7.1 General.20
8.7.2 Linearity of monitor gate amplitude .20
8.7.3 Linearity of monitor gate time-of-flight .21
8.7.4 Monitor gates with analogue outputs .21
8.8 Summation .23
8.8.1 General.23
8.8.2 Procedure .23
8.8.3 Acceptance criteria .24
9 Group 2 tests .24
9.1 Equipment required for group 2 tests .24
9.2 Visual inspection .24
9.2.1 Procedure .
...