EN 131-2:2010+A2:2017
(Main)Ladders - Part 2: Requirements, testing, marking
Ladders - Part 2: Requirements, testing, marking
This European Standard specifies the general design features, requirements and test methods for portable ladders.
It does not apply to step stools or ladders for specific professional use such as firebrigade ladders, roof ladders and mobile ladders.
It does not apply to ladders used for work on or near live electrical systems or installations. For this purpose EN 61478 applies.
NOTE For insulating ladders for use on or near low voltage electrical installations EN 50528 applies.
This European Standard is intended to be used in conjunction with EN 131 1.
For single or multiple hinge joint ladders EN 131 4 applies.
For telescopic ladders EN 131-6 applies.
For mobile ladders with a platform EN 131 7 applies.
Leitern - Teil 2: Anforderungen, Prüfung, Kennzeichnung
Échelles - Partie 2: Exigences, essais, marquage
La présente Norme européenne spécifie les caractéristiques générales de conception, les exigences et les méthodes d’essai applicables aux échelles portables.
Elle ne s’applique pas aux marchepieds ou aux échelles à usage professionnel spécifique tels que les échelles à incendie, les échelles de toit et les échelles escamotables.
Elle ne s’applique pas aux échelles utilisées pour effectuer des travaux sur des installations électriques ou à proximité de circuits électriques sous tension. À cet effet, l’EN 61478 s’applique.
NOTE Pour les échelles isolantes destinées à être utilisées sur ou à proximité d’installations électriques basse tension, l’EN 50528 s’applique.
La présente norme doit être utilisée conjointement avec l’EN 131 1.
Pour les échelles articulées à articulations simple et multiple, l’EN 131 4 s’applique.
Pour les échelles télescopiques, l’EN 131-6 s’applique.
Pour les échelles mobiles avec une plate-forme, l’EN 131 7 s’applique.
Lestve - 2. del: Zahteve, preskušanje, označevanje
Ta evropski standard določa splošne konstrukcijske značilnosti, zahteve in preskusne metode za prenosne lestve.
Ne uporablja se za pručke ali lestve za posebne poklicne uporabe, kot so gasilske lestve, strešne lestve in mobilne lestve.
Ne uporablja se za lestve, ki so namenjene za delo na električnih sistemih ali napravah pod napetostjo ali v njihovi bližini. Za ta namen se uporablja standard EN 61478.
OPOMBA: Za izolirne lestve na ali v bližini nizkonapetostne električne inštalacije se uporablja standard EN 50528.
Ta evropski standard je treba uporabljati v povezavi s standardom EN 131 1.
Za lestve z enojnimi ali več pregibi se uporablja standard EN 131 4.
Za teleskopske lestve se uporablja standard EN 131-6.
Za mobilne lestve s platformo se uporablja standard EN 131 7.
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Leitern - Teil 2: Anforderungen, Prüfung, KennzeichnungÉchelles - Partie 2: Exigences, essais, marquageLadders - Part 2: Requirements, testing, marking97.145LestveLaddersICS:Ta slovenski standard je istoveten z:EN 131-2:2010+A2:2017SIST EN 131-2:2010+A2:2017en,fr,de01-marec-2017SIST EN 131-2:2010+A2:2017SLOVENSKI
STANDARDSIST-TS CEN/TS 16665:20141DGRPHãþD
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 131-2:2010+A2
January
t r s y ICS
{ yä s v w Supersedes EN
s u sæ tã t r s r ªA sã t r s tEnglish Version
Ladders æ Part
tã Requirementsá testingá marking Échelles æ Partie
tã Exigencesá essaisá marquage
Leitern æ Teil
tã Anforderungená Prüfungá Kennzeichnung This European Standard was approved by CEN on
s x April
t r s t and includes Amendment
t approved by CEN on
s y September
t r s xä
egulations which stipulate the conditions for giving this European Standard the status of a national standard without any alterationä Upætoædate lists and bibliographical references concerning such national standards may be obtained on application to the CENæCENELEC Management Centre or to any CEN memberä
translation under the responsibility of a CEN member into its own language and notified to the CENæCENELEC Management Centre has the same status as the official versionsä
CEN members are the national standards bodies of Austriaá Belgiumá Bulgariaá Croatiaá Cyprusá Czech Republicá Denmarká Estoniaá Finlandá Former Yugoslav Republic of Macedoniaá Franceá Germanyá Greeceá Hungaryá Icelandá Irelandá Italyá Latviaá Lithuaniaá Luxembourgá Maltaá Netherlandsá Norwayá Polandá Portugalá Romaniaá Serbiaá Slovakiaá Sloveniaá Spainá Swedená Switzerlandá Turkey and United Kingdomä
EUROPEAN COMMITTEE FOR STANDARDIZATION COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre:
Avenue Marnix 17,
B-1000 Brussels
t r s y CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Membersä Refä Noä EN
s u sæ tã t r s r ªA tã t r s y ESIST EN 131-2:2010+A2:2017
Test sequence . 52 Annex B (informative)
A-deviations . 55 Bibliography . 58
(ISO 6892-1:2009) EN ISO 14125, Fibre-reinforced plastic composites — Determination of flexural properties (ISO 14125:1998) #EN ISO 14644-1, Cleanrooms and associated controlled environments — Part 1: Classification of air cleanliness by particle concentration (ISO 14644-1)$ EN ISO 14731, Welding coordination — Tasks and responsibilities (ISO 14731:2006) 3 Terms and definitions For the purposes of this document, the terms and definitions given in #EN 131-1:2015$and the following apply. 3.1 thermoset plastic plastic that has been cured by heat or by other means such as radiation, catalysts, etc., into a substantially infusible and insoluble state [EN ISO 472:2001] SIST EN 131-2:2010+A2:2017
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.