EN ISO 15548-2:2008
(Main)Non-destructive testing - Equipment for eddy current examination - Part 2: Probe characteristics and verification (ISO 15548-2:2008)
Non-destructive testing - Equipment for eddy current examination - Part 2: Probe characteristics and verification (ISO 15548-2:2008)
ISO 15548-2:2008 identifies the functional characteristics of a probe and its interconnecting elements and provides methods for their measurement and verification.
The evaluation of these characteristics permits a well-defined description and comparability of eddy current equipment.
By careful choice of the characteristics, a consistent and effective eddy current examination system can be designed for a specific application.
Where accessories are used, these should be characterised using the principles of ISO 15548-2:2008.
ISO 15548-2:2008 does not give the extent of verification nor acceptance criteria for the characteristics. These are given in the application documents.
Zerstörungsfreie Prüfung - Technische Ausrüstung für die Wirbelstromprüfung - Teil 2: Kenngrößen von Sensoren und deren Verifizierung (ISO 15548-2:2008)
Dieser Teil von ISO 15548 legt die Funktionskenngrößen eines Sensors und der zugehörigen Verbindungs-elemente fest und enthält Verfahren für ihre Messung und Verifizierung.
Die Beurteilung dieser Kenngrößen ermöglicht eine genaue Beschreibung und Vergleichbarkeit einer Wirbelstromausrüstung.
Durch sorgfältige Auswahl der Kenngrößen kann ein reproduzierbares und effektives Wirbelstrom Prüfsystem für spezifische Anwendungen entworfen werden.
Bei der Verwendung von Zubehörteilen sollten diese nach den Grundlagen dieses Teils von ISO 15548 charakterisiert werden.
Dieser Teil von ISO 15548 enthält weder Vorschriften für den Umfang der Verifizierung noch für die Annahmekriterien der Kenngrößen. Diese sind in den Anwendungsdokumenten enthalten.
Essais non destructifs - Appareillage pour examen par courants de Foucault - Partie 2: Caractéristiques des capteurs et vérifications (ISO 15548-2:2008)
L'ISO 15548-2:2008 identifie les caractéristiques fonctionnelles d'un capteur à courants de Foucault et de ses éléments d'interconnexion et fournit des méthodes pour les mesurer et les vérifier.
L'évaluation de ces caractéristiques permet de donner une description bien définie de l'appareillage à courants de Foucault et d'assurer la comparabilité entre appareillages.
Un système d'examen par courants de Foucault, cohérent et efficace, peut être conçu en procédant à un choix scrupuleux des caractéristiques pour une application spécifique.
Lorsque des accessoires sont mis en œuvre, il convient de les caractériser en appliquant les principes de l'ISO 15548-2:2008.
L'ISO 15548-2:2008 ne fournit pas l'étendue des vérifications ni des critères d'acceptation pour les caractéristiques. Ceux-ci sont définis dans les documents d'application.
Neporušitveno preskušanje - Oprema za preskušanje z vrtinčnimi tokovi - 2. del: Značilnosti sond in preverjanje (ISO 15548-2:2008)
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Zerstörungsfreie Prüfung - Wirbelstromprüfung - Kenngrößen von Prüfeinrichtungen und deren Verifizierung - Teil 2: Kenngrößen von Sensoren und deren Verifizierung (ISO 15548-2:2008)Essais non destructifs - Équipement pour examens par courants de Foucault - Partie 2: Caractéristiques et vérification des sondes (ISO 15548-2:2008)Non-destructive testing - Equipment for eddy current examination - Part 2: Probe characteristics and verification (ISO 15548-2:2008)19.100Neporušitveno preskušanjeNon-destructive testingICS:Ta slovenski standard je istoveten z:EN ISO 15548-2:2008SIST EN ISO 15548-2:2009en,fr,de01-april-2009SIST EN ISO 15548-2:2009SLOVENSKI
STANDARDSIST EN 13860-2:20041DGRPHãþD
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN ISO 15548-2September 2008ICS 19.100Supersedes EN 13860-2:2003
English VersionNon-destructive testing - Equipment for eddy currentexamination - Part 2: Probe characteristics and verification (ISO15548-2:2008)Essais non destructifs - Appareillage pour examen parcourants de Foucault - Partie 2: Caractéristiques descapteurs et vérifications (ISO 15548-2:2008)Zerstörungsfreie Prüfung - Wirbelstromprüfung -Kenngrößen von Prüfeinrichtungen und deren Verifizierung- Teil 2: Kenngrößen von Sensoren und deren Verifizierung(ISO 15548-2:2008)This European Standard was approved by CEN on 6 September 2008.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2008 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN ISO 15548-2:2008: ESIST EN ISO 15548-2:2009
Reference numberISO 15548-2:2008(E)© ISO 2008
INTERNATIONAL STANDARD ISO15548-2First edition2008-09-15Non-destructive testing — Equipment for eddy current examination — Part 2: Probe characteristics and verification Essais non destructifs — Appareillage pour examen par courants de Foucault — Partie 2: Caractéristiques des capteurs et vérifications
ISO 15548-2:2008(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
©
ISO 2008 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body in the country of the requester. ISO copyright office Case postale 56 • CH-1211 Geneva 20 Tel.
+ 41 22 749 01 11 Fax
+ 41 22 749 09 47 E-mail
copyright@iso.org Web
www.iso.org Published in Switzerland
ii © ISO 2008 – All rights reserved
ISO 15548-2:2008(E) © ISO 2008 – All rights reserved iiiContents Page Foreword.iv 1 Scope.1 2 Normative references.1 3 Terms and definitions.1 4 Characteristics of probe and interconnecting elements.1 4.1 General characteristics.1 4.1.1 Application.1 4.1.2 Probe types.2 4.1.3 Interconnecting elements.2 4.1.4 Physical characteristics.2 4.1.5 Safety.3 4.1.6 Environmental conditions.3 4.2 Electrical characteristics.3 4.3 Functional characteristics.3 5 Verification.4 5.1 General.4 5.2 Levels of verification.4 5.3 Verification procedure.5 5.4 Corrective actions.5 6 Measurement of electrical and functional characteristics of a probe.5 6.1 Electrical characteristics.5 6.1.1 General.5 6.1.2 Measurement conditions.5 6.1.3 Resonant frequency of the excitation element.6 6.1.4 Impedance of the excitation element.6 6.1.5 Impedance of the receiving element(s).6 6.2 Functional characteristics.6 6.2.1 General.6 6.2.2 Measurement conditions.7 6.2.3 Surface probes.8 6.2.4 Coaxial probes.19 6.3 Normalized impedance plane diagram.25 7 Influence of interconnecting elements.25 Annex A (informative)
Reference block A6.26 Bibliography.28
ISO 15548-2:2008(E) iv © ISO 2008 – All rights reserved Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 15548-2 was prepared by the European Committee for Standardization (CEN) Technical Committee CEN/TC 138, Non-destructive Testing, in collaboration with ISO Technical Committee TC 135, Non-destructive Testing, Subcommittee SC 4, Eddy current methods, in accordance with the Agreement on technical cooperation between ISO and CEN (Vienna Agreement). ISO 15548 consists of the following parts, under the general title Non-destructive testing — Equipment for eddy current examination: ⎯ Part 1: Instrument characteristics and verification ⎯ Part 2: Probe characteristics and verification ⎯ Part 3: System characteristics and verification
INTERNATIONAL STANDARD ISO 15548-2:2008(E) © ISO 2008 – All rights reserved 1Non-destructive testing — Equipment for eddy current examination — Part 2: Probe characteristics and verification 1 Scope This part of ISO 15548 identifies the functional characteristics of a probe and its interconnecting elements and provides methods for their measurement and verification. The evaluation of these characteristics permits a well-defined description and comparability of eddy current equipment. By careful choice of the characteristics, a consistent and effective eddy current examination system can be designed for a specific application. Where accessories are used, these should be characterised using the principles of this part of ISO 15548. This part of ISO 15548 does not give the extent of verification nor acceptance criteria for the characteristics. These are given in the application documents. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 12718, Non-destructive testing — Eddy current testing — Terminology 3 Terms and definitions For the purposes of this docume
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.