EN 16392-2:2014

Non-destructive testing - Characterisation and verification of ultrasonic phased array equipment - Part 2: Probes

This document covers linear phased array probes used for ultrasonic non-destructive testing in contact technique (with or without a wedge) or in immersion technique, with centre frequencies in the range 0,5 MHz – 10 MHz.
This document specifies the characterisation tests that have to be done at the end of the fabrication of a phased array probe. It defines both methodology and acceptance criteria.
This document does not describe methods and acceptance criteria to characterise the performance of an ultrasonic phased array instrument or the performance of a combined system. These are described in prEN ISO 18563 1 and in prEN ISO 18563 3.

Zerstörungsfreie Prüfung - Charakterisierung und Verifizierung der Ultraschall-Prüfausrüstung mit phasengesteuerten Arrays - Teil 2: Prüfköpfe

Diese Europäische Norm gilt für lineare Phased-Array-Prüfköpfe für die zerstörungsfreie Prüfung mit Ultraschall, die entweder für die Kontakttechnik (mit oder ohne Vorsatzkeil) oder für die Tauchtechnik vorgesehen sind und Mittenfrequenzen von 0,5 MHz bis 10 MHz aufweisen.
Diese Europäische Norm legt die Abnahmeprüfungen nach der Herstellung von Phased-Array-Prüfköpfen fest. Es werden sowohl die Vorgehensweise als auch die Zulässigkeitskriterien festgelegt.
In diesem Dokument sind keine Verfahren und Zulässigkeitskriterien zur Charakterisierung der Leistung eines Phased-Array-Ultraschallgeräts oder der Leistung eines kompletten Phased-Array-Prüfsystems beschrieben. Diese sind in prEN ISO 18563-1 und in prEN ISO 18563-3 beschrieben.

Essais non destructifs - Caractérisation et vérification de l'appareillage de contrôle par ultrasons en multiéléments - Partie 2: Traducteurs

Le présent document traite des traducteurs multi-éléments linéaires utilisés pour les essais non destructifs par
ultrasons - selon la technique par contact (avec ou sans sabot) ou selon la technique par immersion - ayant
une fréquence centrale comprise entre 0,5 MHz et 10 MHz.
Le présent document spécifie les essais de caractérisation qui doivent être effectués à l'issue de la fabrication
d'un traducteur multi-élément. Il définit à la fois la méthodologie et les critères d'acceptation.
Le présent document ne décrit pas les méthodes et critères d'acceptation permettant de caractériser les
performances d'un appareillage de contrôle multi-élément par ultrasons ni celles d'un système complet. Ces
performances sont décrites dans le prEN ISO 18563-1 et le prEN ISO 18563-3.

Neporušitvene preiskave - Karakterizacija in preverjanje ultrazvočne opreme faznih sistemov - 2. del: Sonde

Standard EN 16392-2 zajema sonde linearnega faznega niza, ki se uporabljajo za ultrazvočne neporušitvene preiskave pri tehniki s kontaktom (z ali brez klina) ali pri imerzni tehniki z osrednjimi frekvencami v razponu od 0,5 MHz do 10 MHz. Ta evropski standard določa preizkuse za karakterizacijo, ki morajo biti izvedeni na koncu izdelave sonde linearnega faznega niza. Opredeljuje tako metodologijo kot kriterije sprejemljivosti. Ta dokument ne opisuje metod in kriterijev sprejemljivosti za karakterizacijo delovanja ultrazvočnega instrumenta faznega niza ali delovanja kombiniranega sistema. Ti so opisani v standardih prEN ISO 18563-1 in prEN ISO 18563-3.

General Information

• Status: Withdrawn
• Publication Date: 25-Mar-2014
• Withdrawal Date: 29-Aug-2017
• ICS: 19.100 - Non-destructive testing
• Technical Committee: CEN/TC 138 - Non-destructive testing
• Drafting Committee: CEN/TC 138/WG 2 - Ultrasonic testing
• Current Stage: 9960 - Withdrawal effective - Withdrawal
• Completion Date: 30-Aug-2017
• Ref Project: SIST EN 16392-2:2014 - Non Destructive Testing - Characterisation and verification of ultrasonic phased array systems - Part 2: Probes

Relations

• Replaced By: EN ISO 18563-2:2017 - Non-destructive testing - Characterization and verification of ultrasonic phased array equipment - Part 2: Probes (ISO 18563-2:2017)
• Effective Date: 06-Sep-2017

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Zerstörungsfreie Prüfung - Charakterisierung und Verifizierung der Ultraschall-Prüfausrüstung mit phasengesteuerten Arrays - Teil 2: PrüfköpfeEssais non destructifs - Caractérisation et vérification de l'appareillage de contrôle multi-élément par ultrasons - Partie 2: TraducteursNon Destructive Testing - Characterisation and verification of ultrasonic phased array systems - Part 2: Probes19.100Neporušitveno preskušanjeNon-destructive testingICS:Ta slovenski standard je istoveten z:EN 16392-2:2014SIST EN 16392-2:2014en,fr,de01-julij-2014SIST EN 16392-2:2014SLOVENSKI
STANDARD
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 16392-2
March 2014 ICS 19.100 English Version
Non-destructive testing - Characterisation and verification of ultrasonic phased array equipment - Part 2: Probes
Essais non destructifs - Caractérisation et vérification de l'appareillage de contrôle par ultrasons en multiéléments - Partie 2: Traducteurs
Zerstörungsfreie Prüfung - Charakterisierung und Verifizierung der Ultraschall-Prüfausrüstung mit phasengesteuerten Arrays - Teil 2: Prüfköpfe This European Standard was approved by CEN on 6 February 2014.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2014 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 16392-2:2014 ESIST EN 16392-2:2014

2 Contents Page
Foreword .3 1 Scope .4 2 Normative references .4 3 Terms and definitions .4 4 General requirements for compliance .4 5 Technical specification for phased array probes .5 6 Test equipment .7 7 Performance tests for phased array probes .7
1 Scope This European Standard covers linear phased array probes used for ultrasonic non-destructive testing in contact technique (with or without a wedge) or in immersion technique, with centre frequencies in the range 0,5 MHz – 10 MHz. This European Standard specifies the characterisation tests that have to be done at the end of the fabrication of a phased array probe. It defines both methodology and acceptance criteria. This document does not describe methods and acceptance criteria to characterise the performance of an ultrasonic phased array instrument or the performance of a combined system. These are described in prEN ISO 18563-1 and in prEN ISO 18563-3. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 16018, Non-destructive testing - Terminology - Terms used in ultrasonic testing with phased arrays EN 1330-2, Non-destructive testing - Terminology - Part 2: Terms common to the non-destructive testing methods. EN 1330-4, Non-destructive testing - Terminology - Part 4: Terms used in ultrasonic testing EN ISO 2400, Non-destructive testing - Ultrasonic testing - Specification for calibration block No. 1 (ISO 2400:2012) 3 Terms and definitions For the purposes of this document, the terms and definitions given in EN 1330-2, EN 1330-4, EN 16018 and the following apply. 3.1 phased array probe data sheet document describing the general characteristics of the same type of phased array probes 3.2 phased array probe certificate document showing compliance with this European Standard giving the measured values of the required parameters of one specific phased array probe 4 General requirements for compliance An ultrasonic phased array probe complies with this document if it satisfies the following conditions: a) the probe shall comply with Clause 7; b) a declaration of conformity is issued: SIST EN 16392-2:2014
...