EN 12982:2009

Industrial valves - End-to-end and centre-to-end dimensions for butt welding end valves

This European Standard specifies the end to end and centre to end dimensions for steel butt welding end valves with connecting dimensions of welding ends in compliance with EN 12627, used in PN and Class designated piping systems.
The range of PN is:
-   PN 10; PN 16; PN 25; PN 40; PN 63; PN 100; PN 160; PN 250; PN 320; PN 400.
The range of Class is:
-   Class 150, Class 300, Class 600, Class 900, Class 1 500, Class 2 500.
The range of nominal size is:
-   DN 8; DN 10; DN 15; DN 20; DN 25; DN 32; DN 40; DN 50; DN 65; DN 80; DN 100; DN 125; DN 150; DN 200; DN 250; DN 300; DN 350; DN 400; DN 450; DN 500; DN 600; DN 700; DN 750; DN 800; DN 900, DN 1 000; DN 1 200.
NOTE 1   DN 750 is not applicable to PN designated valves.
NOTE 2   See Annex B for the relationship between nominal size (DN) and nominal pipe size (NPS).
NOTE 3   Valves having welding end profiles different from those specified in EN 12627, may use the same dimensions than those specified in Table 1.

Industriearmaturen - Baulängen für Armaturen mit Anschweißenden

Diese Europäische Norm legt die Baulängen für Armaturen aus Stahl mit Anschweißenden und Anschluss¬maßen nach EN 12627 fest, die in nach PN und Class bezeichneten Rohrleitungssystemen verwendet werden.
Der PN-Bereich umfasst:
-   PN 10; PN 16; PN 25; PN 40; PN 63; PN 100; PN 160; PN 250; PN 320; PN 400.
Der Class-Bereich umfasst:
-   Class 150, Class 300, Class 600, Class 900, Class 1 500, Class 2 500.
Der Nennweitenbereich umfasst:
-   DN 8; DN 10; DN 15; DN 20; DN 25; DN 32; DN 40; DN 50; DN 65; DN 80; DN 100; DN 125; DN 150; DN 200; DN 250; DN 300; DN 350; DN 400; DN 450; DN 500; DN 600; DN 700; DN 750; DN 800; DN 900; DN 1 000; DN 1 200.
ANMERKUNG 1   DN 750 gilt nicht für nach PN bezeichnete Armaturen.
ANMERKUNG 2   Siehe Anhang B zum Verhältnis zwischen Nennweite (DN) und Rohr-Nennweite (NPS).
ANMERKUNG 3   Für Armaturen mit Anschweißenden, die nicht in EN 12627 festgelegt sind, können die entsprechenden Maße nach Tabelle 1 verwendet werden.

Robinetterie industrielle - Dimensions entre extrémités et d'extrémité à axe des appareils de robinetterie à souder en bout

La présente Norme européenne spécifie les dimensions entre extrémités et d'extrémité à axe des appareils de robinetterie en acier à souder en bout dont les dimensions des extrémités à souder en bout sont conformes à l’EN 12627 et qui sont utilisés dans les systèmes de canalisation désignés par PN et Class.
La gamme des PN est la suivante :
-   PN 10 ; PN 16 ; PN 25 ; PN 40 ; PN 63 ; PN 100 ; PN 160 ; PN 250 ; PN 320 ; PN 400.
La gamme des "Class" est la suivante :
-   Class 150 ; Class 300 ; Class 600 ; Class 900 ; Class 1 500 ; Class 2 500.
La gamme des diamètres nominaux est la suivante :
-   DN 8 ; DN 10 ; DN 15 ; DN 20 ; DN 25 ; DN 32 ; DN 40 ; DN 50 ; DN 65 ; DN 80 ; DN 100 ; DN 125 ; DN 150 ; DN 200 ; DN 250 ; DN 300 ; DN 350 ; DN 400 ; DN 450 ; DN 500 ; DN 600 ; DN 700 ; DN 750 ; DN 800 ; DN 900 ; DN 1 000 ; DN 1 200.
NOTE 1   DN 750 n'est pas applicable aux appareils de robinetterie désignés PN.
NOTE 2   Voir l'Annexe B pour la relation entre le diamètre nominal (DN) et la dimension nominale de la tuyauterie (NPS).
NOTE 3   Les appareils de robinetterie avec des profils d’extrémités à souder différents de ceux spécifiés dans l’EN 12627, peuvent avoir les mêmes dimensions que celles spécifiées dans le Tableau 1.

Industrijski ventili - Vgradne dolžine za ventile z varjenim priključkom

General Information

• Status: Published
• Publication Date: 18-Aug-2009
• ICS: 23.060.01 - Valves in general
• Technical Committee: CEN/TC 69 - Industrial valves
• Drafting Committee: CEN/TC 69/WG 1 - Basic standards
• Current Stage: 9093 - Decision to confirm - Review Enquiry
• Completion Date: 29-May-2020
• Directive: 97/23/EC - Directive 97/23/EC of the European Parliament and of the Council of 29 May 1997 on the approximation of the laws of the Member States concerning pressure equipment
• Mandate: M/071 - Mandate to CEN for standardization in the field of Pressure equipment
• Ref Project: SIST EN 12982:2009 - Industrial valves - End-to-end and centre-to-end dimensions for butt welding end valves

Relations

• Replaces: EN 12982:2000 - Industrial valves - End-to-end and centre-to-end dimensions for butt welding end valves
• Effective Date: 22-Dec-2008

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.OMXþNRPIndustriearmaturen - Baulängen für Armaturen mit AnschweißendenRobinetterie industrielle - Dimensions entre extrémités et d'extrémité a axe des appareils de robinetterie a souder en boutIndustrial valves - End-to-end and centre-to-end dimensions for butt welding end valves23.060.01Ventili na splošnoValves in generalICS:Ta slovenski standard je istoveten z:EN 12982:2009SIST EN 12982:2009en,fr,de01-oktober-2009SIST EN 12982:2009SLOVENSKI
STANDARDSIST EN 12982:20011DGRPHãþD

EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 12982August 2009ICS 23.060.01Supersedes EN 12982:2000
English VersionIndustrial valves - End-to-end and centre-to-end dimensions forbutt welding end valvesRobinetterie industrielle - Dimensions entre extrémités etd'extrémité à axe des appareils de robinetterie à souder enboutIndustriearmaturen - Baulängen für Armaturen mitAnschweißendenThis European Standard was approved by CEN on 17 July 2009.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre:
Avenue Marnix 17,
B-1000 Brussels© 2009 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 12982:2009: ESIST EN 12982:2009

Origin of basic series . 18Annex B (informative)
Relationship between DN (nominal size) and nominal pipe size (NPS) . 20Bibliography . 21 SIST EN 12982:2009

3 Foreword This document (EN 12982:2009) has been prepared by Technical Committee CEN/TC 69 “Industrial valves”, the secretariat of which is held by AFNOR. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by February 2010, and conflicting national standards shall be withdrawn at the latest by February 2010. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 12982:2000. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom.
5 1 Scope This European Standard specifies the end-to-end and centre-to-end dimensions for steel butt-welding end valves with connecting dimensions of welding ends in compliance with EN 12627, used in PN and Class designated piping systems. The range of PN is:  PN 10; PN 16; PN 25; PN 40; PN 63; PN 100; PN 160; PN 250; PN 320; PN 400. The range of Class is:  Class 150, Class 300, Class 600, Class 900, Class 1 500, Class 2 500. The range of nominal size is:  DN 8; DN 10; DN 15; DN 20; DN 25; DN 32; DN 40; DN 50; DN 65; DN 80; DN 100; DN 125; DN 150; DN 200; DN 250; DN 300; DN 350; DN 400; DN 450; DN 500; DN 600; DN 700; DN 750; DN 800; DN 900, DN 1 000; DN 1 200. NOTE 1 DN 750 is not applicable to PN designated valves. NOTE 2 See Annex B for the relationship between nominal size (DN) and nominal pipe size (NPS). NOTE 3 Valves having welding end profiles different from those specified in EN 12627, may use the same dimensions than those specified in Table 1. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 736-1:1995, Valves — Terminology — Part 1: Definition of types of valves EN 736-2:1997, Valves — Terminology — Part 2: Definition of components of valves 3 Terms and definitions For the purposes of this document, the terms and definitions given in EN 736-1:1995 and EN 736-2:1997 and the following apply. 3.1 end-to end dimensions (ETE) distance expressed between the ends of the body for straight pattern valves other than those with flanged ends 3.2 centre-to-end dimensions (CTE) distance expressed between one of the ends of the body and the centre of the body for angle pattern valves other than those with flanged ends
a) Straight and oblique pattern valveb)Angle pattern valve Key 1 ETE 2 CTE Figure 1 – ETE and CTE dimensions 4 Dimensions and tolerances 4.1 Basic series The basic series of ETE and CTE dimensions are given in Table 1. For each type of valve, the basic series to be taken into consideration shall be in accordance with Tables 3 to 12. NOTE 1 Table 1 gives complete series. In Tables 3 to 12 the columns of series may be reduced. NOTE 2 For certain sizes/types of valves, alternative dimensions are permitted and are specified in Tables 3 to 12. NOTE 3 Basic series numbers are corresponding to the basic series given in EN 558. 4.2 Tolerances Tolerances on ETE and CTE dimensions shall be in accordance with Table 2. SIST EN 12982:2009

7 Table 1 — Dimensions of basic series
Dimensions in millimetres DN Basic series 1 2 4 5 7 8 a 9 a 10 11 a 14 15 21 24 a 26 32 a 33 54 55 56 57 a 58 a 59 a 60 8 —
— — —
— — — — — — — — — — — — — — — — 10
210 — — 108
90 105 — — 115 — — — — — — — — — — — —
102 15
165 108
90 105
57 115 —
76 — —
264 — 108 132
108 20
190 117
95 115
64 120 —
89 —
273 114 114 137
117 25
216 127 100 115
70 125
216 108
160 102 —
308 127 127 154
127 32
229 146 105 130
76 130
229 114
180 108 —
349 140 140 175
140 40
241 159 115 130
83 140
241 121
240 114
384 152 152 193
165 50
292 190 125 150
203 102 150
267 146
250 133
451 184 184 225
216 65
330 216 145 170
216 108 170
292 165
290 146
508 210 210 254
241 80
356 254 155 190
241 121 180
318 178
310 159
578 190 235 289
283 100
432 305 175 215
292 146 190
356 216
350 178
673 229 273 337
305 125
508 356 200 250
330 178 200
400 254
400 200
794 279 337 397
381 150
559 406 225 275
356 203 210
444 279
450 222
914 305 352 457
403 200
660 521 275 325
495 248 230
533 330
550 279
832 1 022 368 416 511
419 250
787 635 325 390
622 311 250
622 394
650 311
991 1 270 419 495 635
457 300
507 838 749 375 450
698 349 270
711 419
750 356
965 1 130 1 422 483 565 711
502 350
980 1 025
889 — 425 515
787 394 290
838 —
850 —
889 1 029 1 257 — 514 629 —
572 400 1 100 1 150
991 — 475 575
914 457 310
864 —
950 —
991 1 130 1 384 — 660 — —
610 450 1 200 1 275
914 1 092 — 500 —
978 483 330
978 — 1 050 — 1 092 1 219 1 537 — 737 — —
660 500 1 250 1 400
991 1 194 — — 700
978 — 350
700 1 016 — 1 150 — 1 194 1 321 1 664 — 825 — —
711 600 1 450 1 600 1 143 1 397 —
1 295 — 390
800 1 346 — 1 350 — 1 397 1 549 1 943 — 991 — —
813 700 1 650
1 346 1 549 —
1 448 — 430
900 1 499 — 1 550 — 1 549 — — — — — —
914 750 —
1 397 1 651 —
1 524 — — — 1 594 — — — — — — — — — —
914 800 1 850
— 1 651 —
1 676 — 470 1 000 1 778 — 1 750 — — — — — — — —
965 900 2 050
1 727 2 083 —
1 956 — 510 1 100 2 083 — 1 950 — — — — — — — — 1 016 1 000 2 250
1 981 — —
— — 550 1 200 — — 2 150 — — — — — — — — — 1 200 —
— — —
— — 630 1 400 — — — — — — — — — — — —
Dimensions in millimetres DN Basic series 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 78 79 80 81 82 a 83 a
8 — — — — — — — — — — — — — — — — — — —
65 — —
10 — — — 130
270— — — — — — — — — — —
65 —
15 140 — — 130
270— — —
203 194
108— —
65 —
20 152 — — 130
270— — —
206 194
117— —
70 —
25 165 — — 130
85 100
210 197
127— —
85 —
32 178 — — 160
180100 110
237— — — — —
140— — 100 — 105
40 190 —
190 180
210140 125
251 235
165— — 110 — 105
50 216
216 210
250150 150
286 292
178— — 125 — 115
65 241
241 290
340170 190
311 292
190— — 150 — 145
80 283
283 310
380180 220
337 318
203— — 180 152 155
100 305
305 350
430190 270
394 368
229— — 210 178 175
125 381
381— 400
500200 330
533— — — — — — — — — 216 200
150 403
457 480
550210 430
508 508
394330 403 — 254 225
200 419
521 600
650430 460
610 610
457350 419 — 330 275
250 457
559 730
775450 —
752 762
9911 016
533375 457 — 394 325
300 502
635 850
900470 —
9911 041
819 914 1 1301 118
610400 502 — 457 375
350 572
762 — 1 025490 —
9911 0671 118
8511 029 — 1 257—
686425 530 — 495 —
400 610
838 — 1 150510 — 1 1001 0921 1941 2451 0161 108 — 1 422—
762450 550 — — —
450 660
914 — — — — — — 1 3461 3971 143— — 1 727—
864540 600 — — —
500 711
991 — 1 400550 — 1 250— 1 473— — — — — —
914560 620 — — —
600 813 1 1431 143 — — 590 — — — — — — — — — — 1 067600 670 — — —
700 — — 1 346 — — 630 — — — — — — — — — — 1 244670 750 — — —
750 — — 1 397 — — — — — — — — — — — — — — 700 795 — — —
800 — — 1 524 — — 670 — — — — — — — — — — — — — — — —
900 — — 1 727 — — 710 — — — — — — — — — — — — — — — — 1 000
— — — 750 — — — — — — — — — — — — — — — — 1 200
— — — 830 — — — — — — — — — — — — — — — —
9 Table 1 (continued)
Dimensions in millimetres DN Basic series 84 85 86 a 87 a 88 89 90 92 93 102 103 104 111
8 — — — — — — —
— — — — — — — — — — — —
10 150 150
75 150 130
230115 — — — — — — — — — — — —
15 150 150
75 150 130
230115 — — — 318 — — — — — — — —
20 150 160
80 160 130
260130 — — — 318 — — — — — — — —
25 160 160
80 160 130
260130 — — — 318 — — — — — — — —
32 180 250
90 125 270 160
300150 — — — — — — — — — — — —
40 210 250 105 125 270 160
300150 — — — 359 — — — — — — — —
50 250 250 125 125 270 190
350400 — — — — — — — —
65 420 480 210 150 — —
425400 — — — — — — — —
80 460 530 230 265 — —
470498 — — — — — — — —
100 510 620 255 310 — —
550575 — — — — — — — —
125 600 720 300 360 — —
650— — — — — — — — —
150 650 820 325 410 — —
750819 — — — — — — — —
200 750 950 375 475 — —
9001 029 — — — — — — — —
250 — — — — — —
9501 0501 270 — — — — — — — —
300 — — — — — — 1 0501 050
9501 1501 2501 422 — — — — — — — —
350 — — — — — — 1 200
1 0501 3501 4501 803 — — — — — — — —
400 — — — — — — 1 350
1 2001 5501 650— — — — — — — — —
450 — — — — — — 1 500
1 3501 7501 850— — — — — — — — —
500 — — — — — — 1 650
1 5001 9502 050— — — — — — — — —
600 — — — — — — —
— — — — — — — — — — — —
700 — — — — — — —
— — — — — — — — — — — —
750 — — — — — — —
— — — — — — — — — — — —
800 — — — — — — —
— — — — — — — — — — — —
900 — — — — — — —
— — — — — — — — — — — — 1 000 — — — — — — —
— — — — — — — — — — — — 1 200 — — — — — — —
— — — — — — — — — — — — a CTE dimensions for angle pattern valves.
Dimensions in millimetres ETE or CTE dimension Tolerance above up to and including
250 ± 2
500 ± 3
800 ± 4
800 1 000 ± 5 1 000 1 600 ± 6 1 600 2 500 ± 8
11 Table 3 — Gate valves PN/Class ETE series 4 5 15 26 33 54 55 56 60 61 69 70 71 90 102 103 104 PN 10 — PN 16
X
X
...