EN 61076-1:2006
(Main)Connectors for electronic equipment - Product requirements - Part 1: Generic specification
Connectors for electronic equipment - Product requirements - Part 1: Generic specification
Establishes uniform specifications and technical information for connectors. Is applicable to a family of connectors for use in electronic and electrical equipment; does not cover connectors designed for use at radio frequencies.
Steckverbinder für elektronische Einrichtungen - Produktanforderungen - Teil 1: Fachgrundspezifikation
Connecteurs pour équipements électroniques - Exigences de produit - Partie 1: Spécification générique
Etablit des spécifications et des caractéristiques techniques uniformes pour les connecteurs. Est applicable à une famille de connecteurs destinés à être utilisés dans des équipements électriques et électroniques; ne couvre pas les connecteurs conçus pour être utilisés aux fréquences radioélectriques.
Konektorji za elektronsko opremo – Zahteve za izdelek – 1. del: Rodovna specifikacija (IEC 61076-1:2006)
Ta del standarda IEC 61076 določa enotne specifikacije in tehnične informacije za konektorje. Ta del standarda IEC 61076 se uporablja za družino konektorjev, ki se uporabljajo za elektronsko in električno opremo; konektorji, ki so zasnovani za uporabo na radijskih frekvencah, niso zajeti.
General Information
Relations
Standards Content (Sample)
SLOVENSKI SIST EN 61076-1:2006
STANDARD
oct 2006
Konektorji za elektronsko opremo – Zahteve za izdelek – 1. del: Rodovna
specifikacija (IEC 61076-1:2006)
Connectors for electronic equipment – Product requirements – Part 1: Generic
specification (IEC 61076-1:2006)
ICS 31.220.10 Referenčna številka
© Standard je založil in izdal Slovenski inštitut za standardizacijo. Razmnoževanje ali kopiranje celote ali delov tega dokumenta ni dovoljeno
EUROPEAN STANDARD
EN 61076-1
NORME EUROPÉENNE
June 2006
EUROPÄISCHE NORM
ICS 31.220.10 Supersedes EN 61076-1:1995 + A1:1996 + A2:2001
English version
Connectors for electronic equipment -
Product requirements
Part 1: Generic specification
(IEC 61076-1:2006)
Connecteurs pour équipements Steckverbinder für elektronische
électroniques - Einrichtungen -
Exigences de produit Produktanforderungen
Partie 1: Spécification générique Teil 1: Fachgrundspezifikation
(CEI 61076-1:2006) (IEC 61076-1:2006)
This European Standard was approved by CENELEC on 2006-05-01. CENELEC members are bound to comply
with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard
the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the Central Secretariat or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and notified
to the Central Secretariat has the same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Cyprus, the Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.
CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
Central Secretariat: rue de Stassart 35, B - 1050 Brussels
© 2006 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 61076-1:2006 E
Foreword
The text of document 48B/1621/FDIS, future edition 2 of IEC 61076-1, prepared by SC 48B, Connectors,
of IEC TC 48, Electromechanical components and mechanical structures for electronic equipment, was
submitted to the IEC-CENELEC parallel vote and was approved by CENELEC as EN 61076-1 on
2006-05-01.
This European Standard supersedes EN 61076-1:1995 + A1:1996 + A2:2001.
This Standard is to be used in conjunction with EN 62197-1:2006.
The following dates were fixed:
– latest date by which the EN has to be implemented
at national level by publication of an identical
national standard or by endorsement (dop) 2007-02-01
– latest date by which the national standards conflicting
with the EN have to be withdrawn (dow) 2009-05-01
Annex ZA has been added by CENELEC.
__________
Endorsement notice
The text of the International Standard IEC 61076-1:2006 was approved by CENELEC as a European
Standard without any modification.
__________
- 3 - EN 61076-1:2006
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
NOTE When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD
applies.
Publication Year Title EN/HD Year
IEC 60050-581 1978 International Electrotechnical Vocabulary - -
(IEV) -
Chapter 581: Electromechanical components
for electronic equipment
1)
IEC 60068-1 1988 Environmental testing - EN 60068-1 1994
+ corr. October 1988 Part 1: General and guidance
IEC 60512 Series Connectors for electronic equipment - Tests EN 60512 Series
and measurements
IEC 60664-1 (mod) 1992 Insulation coordination for equipment within
+ A1 2000 low-voltage systems -
+ A2 2002 Part 1: Principles, requirements and tests
EN 60664-1 2003
IEC 62197-1 2006 Connectors for electronic equipment - Quality EN 62197-1 2006
assessment requirements -
Part 1: Generic specification
IEC/TR 62225 2001 Guidance on terms for connectors and - -
mechanical structures in electronic equipment
IEC Guide 109 2003 Environmental aspects - Inclusion in - -
electrotechnical product standards
ISO 129-1 2004 Technical drawings - Indication of dimensions - -
and tolerances -
Part 1: General principles
ISO 286-1 1988 ISO system of limits and fits - EN 20286-1 1993
Part 1: Bases of tolerances, deviations and
fits
ISO 286-2 1988 ISO system of limits and fits - EN 20286-2 1993
Part 2: Tables of standard tolerance grades
and limit deviations for holes and shafts
ISO 1000 1992 SI units and recommendations for the use of - -
their multiples and of certain other units
ISO 1101 2004 Geometrical Product Specifications (GPS) -- EN ISO 1101 2005
Geometrical tolerancing -- Tolerances of
form, orientation, location and run-out
1)
EN 60068-1 includes A1 to IEC 60068-1
Publication Year Title EN/HD Year
ISO 1302 2002 Geometrical Product Specifications (GPS) - EN ISO 1302 2002
Indication of surface texture in technical
product documentation
NORME CEI
INTERNATIONALE
IEC
61076-1
INTERNATIONAL
Deuxième édition
STANDARD
Second edition
2006-04
Connecteurs pour équipements électroniques –
Exigences de produit –
Partie 1:
Spécification générique
Connectors for electronic equipment –
Product requirements –
Part 1:
Generic specification
IEC 2006 Droits de reproduction réservés Copyright - all rights reserved
Aucune partie de cette publication ne peut être reproduite ni No part of this publication may be reproduced or utilized in any
utilisée sous quelque forme que ce soit et par aucun procédé, form or by any means, electronic or mechanical, including
électronique ou mécanique, y compris la photocopie et les photocopying and microfilm, without permission in writing from
microfilms, sans l'accord écrit de l'éditeur. the publisher.
International Electrotechnical Commission, 3, rue de Varembé, PO Box 131, CH-1211 Geneva 20, Switzerland
Telephone: +41 22 919 02 11 Telefax: +41 22 919 03 00 E-mail: inmail@iec.ch Web: www.iec.ch
CODE PRIX
S
PRICE CODE
Commission Electrotechnique Internationale
International Electrotechnical Commission
МеждународнаяЭлектротехническаяКомиссия
Pour prix, voir catalogue en vigueur
For price, see current catalogue
61076-1 IEC:2006 – 3 –
CONTENTS
FOREWORD.5
INTRODUCTION.9
1 General .19
1.1 Scope.19
1.2 General considerations relating to specifications .19
1.3 Normative references .21
1.4 Performance characteristics .23
2 Technical information .27
2.1 Terms and definitions .27
2.2 System of levels .27
2.3 Classification into climatic categories .31
2.4 Clearance and creepage distances.31
2.5 Current-carrying capacity .31
2.6 IEC type designation .31
2.7 Marking .31
3 Dimensional information .33
3.1 Drawings and dimensions.33
3.2 System of lettering .33
3.3 Purpose .33
3.4 Detailed information .35
3.5 Gauges .35
4 Quality assessment procedures.35
5 Tests and test schedules .37
5.1 General aspects .37
5.2 Test schedules .37
5.3 Test procedures and measuring methods .39
5.4 Preconditioning .39
5.5 Wiring and mounting of specimens .39
Annex A (normative) Common lettering system to be used in drawings .41
Figure 1 – Actual detail specification structure .11
Figure 2 – New documentation structure for specifications drafted in SC 48B –
Separation of product and quality assessment requirements.13
Figure A.1 – Two part connectors .41
Figure A.2 – Edge-socket connector .43
Table 1 – Climatic categories – selected values.31
61076-1 IEC:2006 – 5 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
___________
CONNECTORS FOR ELECTRONIC EQUIPMENT –
PRODUCT REQUIREMENTS –
Part 1: Generic specification
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any
equipment declared to be in conformity with an IEC Publication.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn t
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.