EN IEC 61076-2-114:2020
(Main)Connectors for electrical and electronic equipment - Product requirements - Part 2-114: Circular connectors - Detail specification for connectors with M8 screw-locking with power contacts and signal contacts for data transmission up to 100 MHz
Connectors for electrical and electronic equipment - Product requirements - Part 2-114: Circular connectors - Detail specification for connectors with M8 screw-locking with power contacts and signal contacts for data transmission up to 100 MHz
IEC 61076-2-114:2020 describes circular connectors with M8 screw locking typically used for data and power transmissions in industrial applications. These connectors consist of fixed and free connectors that are either rewireable or non-rewireable. Data transmission performance is for Category 5 up to 100 MHz. Two coded versions, identified as D-coded and P-coded, are provided that differ by their pin size and optionally by number of poles, hence by the function provided for field applications. Male connectors have round contacts Ø 0,8 mm for D-coded, and Ø 1 mm for P-coded connectors. The coding provided by this document prevents the mating of accordingly coded male or female connectors to any other similarly sized interfaces covered by other standards.
Steckverbinder für elektrische und elektronische Einrichtungen - Produktanforderungen - Teil 2-114: Rundsteckverbinder - Bauartspezifikation für Steckverbinder M8 mit Schraubverriegelung mit Daten- und Leistungskontakten zur Datenübertragung bis 100 MHz
Connecteurs pour équipements électriques et électroniques - Exigences de produit - Partie 2-114: Connecteurs circulaires - Spécification particulière pour les connecteurs avec verrouillage à vis M8 avec contacts de puissance et contact de signaux pour transmission de données jusqu'à 100 MHz
IEC 61076-2-114:2020 décrit des connecteurs circulaires avec verrouillage à vis M8 typiquement utilisés pour la transmission de données et de puissance dans des applications industrielles. Ces connecteurs se composent d’embases et de fiches démontables ou non. Les performances de transmission de données de la catégorie 5 vont jusqu'à 100 MHz. Deux versions codées, identifiées par codage D et codage P, sont prévues. Elles diffèrent par la taille de leurs broches et, facultativement, par le nombre de pôles, donc par la fonction prévue pour les applications de terrain. Les connecteurs mâles possèdent des contacts arrondis de 0,8 mm de diamètre pour les connecteurs à codage D et de 1 mm de diamètre pour les connecteurs à codage P. Les codages prévus par le présent document empêchent l'accouplement de connecteurs mâles ou femelles codés ainsi avec toute autre interface de même taille couverte par d'autres normes.
Konektorji za električno in elektronsko opremo - Zahteve za izdelek - 2-114. del: Okrogli konektorji - Podrobna specifikacija za konektorje z vijačno zaporo M8 s tokovnimi in signalnimi kontakti za prenos podatkov do 100 MHz (IEC 61076-2-114:2020)
General Information
Standards Content (Sample)
SLOVENSKI STANDARD
01-januar-2021
Konektorji za električno in elektronsko opremo - Zahteve za izdelek - 2-114. del:
Okrogli konektorji - Podrobna specifikacija za konektorje z vijačno zaporo M8 s
tokovnimi in signalnimi kontakti za prenos podatkov do 100 MHz (IEC 61076-2-
114:2020)
Connectors for electrical and electronic equipment - Product requirements - Part 2-114:
Circular connectors - Detail specification for connectors with M8 screw-locking with
power contacts and signal contacts for data transmission up to 100 MHz (IEC 61076-2-
114:2020)
Steckverbinder für elektrische und elektronische Einrichtungen - Produktanforderungen –
Teil 2-114: Rundsteckverbinder - Bauartspezifikation für Steckverbinder M8 mit
Schraubverriegelung zur Stromversorgung und Datenübertragung (IEC 61076-2-
114:2020)
Connecteurs pour équipements électriques et électroniques - Exigences de produit -
Partie 2-114: Connecteurs circulaires - Spécification particulière pour les connecteurs
pour transmission de puissance et de données avec verrouillage à vis M8 (IEC 61076-2-
114:2020)
Ta slovenski standard je istoveten z: EN IEC 61076-2-114:2020
ICS:
31.220.10 Vtiči in vtičnice, konektorji Plug-and-socket devices.
Connectors
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD EN IEC 61076-2-114
NORME EUROPÉENNE
EUROPÄISCHE NORM
October 2020
ICS 31.220.10
English Version
Connectors for electrical and electronic equipment - Product
requirements - Part 2-114: Circular connectors - Detail
specification for connectors with M8 screw-locking with power
contacts and signal contacts for data transmission up to 100
MHz
(IEC 61076-2-114:2020)
Connecteurs pour équipements électriques et électroniques Steckverbinder für elektrische und elektronische
- Exigences de produit - Partie 2-114: Connecteurs Einrichtungen - Produktanforderungen - Teil 2-114:
circulaires - Spécification particulière pour les connecteurs Rundsteckverbinder - Bauartspezifikation für
avec verrouillage à vis M8 avec contacts de puissance et Steckverbinder M8 mit Schraubverriegelung mit Daten- und
contact de signaux pour transmission de données jusqu'à Leistungskontakten zur Datenübertragung bis 100 MHz
100 MHz (IEC 61076-2-114:2020)
(IEC 61076-2-114:2020)
This European Standard was approved by CENELEC on 2020-10-29. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2020 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN IEC 61076-2-114:2020 E
European foreword
The text of document 48B/2814/FDIS, future edition 1 of IEC 61076-2-114, prepared by SC 48B
"Electrical connectors" of IEC/TC 48 "Electrical connectors and mechanical structures for electrical
and electronic equipment" was submitted to the IEC-CENELEC parallel vote and approved by
CENELEC as EN IEC 61076-2-114:2020.
The following dates are fixed:
• latest date by which the document has to be implemented at national (dop) 2021-07-29
level by publication of an identical national standard or by endorsement
• latest date by which the national standards conflicting with the (dow) 2023-10-29
document have to be withdrawn
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
Endorsement notice
The text of the International Standard IEC 61076-2-114:2020 was approved by CENELEC as a
European Standard without any modification.
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments)
applies.
NOTE 1 Where an International Publication has been modified by common modifications, indicated by (mod),
the relevant EN/HD applies.
NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is available
here: www.cenelec.eu.
Publication Year Title EN/HD Year
IEC 60050-581 - International Electrotechnical Vocabulary - - -
Part 581: Electromechanical components
for electronic equipment
IEC 60068-1 - Basic environmental testing procedures - - -
Part 1: General and guidance
IEC 60068-2-60 - Environmental testing - Part 2-60: Tests - EN 60068-2-60 -
Test Ke: Flowing mixed gas corrosion test
IEC 60352 series Solderless connections EN 60352 series
IEC 60512-2-1 - Connectors for electronic equipment - Tests EN 60512-2-1 -
and measurements - Part 2-1: Electrical
continuity and contact resistance tests -
Test 2a: Contact resistance - Millivolt level
method
IEC 60512-3-1 - Connectors for electronic equipment - Tests EN 60512-3-1 -
and measurements - Part 3-1: Insulation
tests - Test 3a: Insulation resistance
IEC 60512-4-1 - Connectors for electronic equipment - Tests EN 60512-4-1 -
and measurements - Part 4-1: Voltage
stress tests - Test 4a: Voltage proof
IEC 60512-5-2 - Connectors for electronic equipment - Tests EN 60512-5-2 -
and measurements - Part 5-2: Current-
carrying capacity tests - Test 5b: Current-
temperature derating
IEC 60512-6-3 - Connectors for electronic equipment - Tests EN 60512-6-3 -
and measurements - Part 6-3: Dynamic
stress tests - Test 6c: Shock
Publication Year Title EN/HD Year
IEC 60512-6-4 - Connectors for electronic equipment - Tests EN 60512-6-4 -
and measurements - Part 6-4: Dynamic
stress tests - Test 6d: Vibration (sinusoidal)
IEC 60512-8-1 - Connectors for electronic equipment - Tests EN 60512-8-1 -
and measurements - Part 8-1: Static load
tests (fixed connectors) - Test 8a: Static
load, transverse
IEC 60512-9-1 - Connectors for electronic equipment - Tests EN 60512-9-1 -
and measurements - Part 9-1: Endurance
tests - Test 9a: Mechanical operation
IEC 60512-12-2 - Connectors for electronic equipment - Tests EN 60512-12-2 -
and measurements - Part 12-2: Soldering
tests - Test 12b: Solderability, wetting,
soldering iron method
IEC 60512-13-2 - Connectors for electronic equipment - Tests EN 60512-13-2 -
and measurements - Part 13-2: Mechanical
operation tests - Test 13b: Insertion and
withdrawal forces
IEC 60512-13-5 - Connectors for electronic equipment - Tests EN 60512-13-5 -
and measurements - Part 13-5: Mechanical
operation tests - Test 13e: Polarizing and
keying method
IEC 60512-15-6 - Connectors for electronic equipment - Tests EN 60512-15-6 -
and measurements - Part 15-6: Connector
tests (mechanical) - Test 15f: Effectiveness
of connector coupling devices
IEC 60512-19-3 - Electromechanical components for EN 60512-19-3 -
electronic equipment - Basic testing
procedures and measuring methods - Part
19: Chemical resistance tests - Section 3:
Test 19c - Fluid resistance
IEC 60512-25-7 2004 Connectors for electronic equipment - Tests EN 60512-25-7 2005
and measurements - Part 25-7: Test 25g -
Impedance, reflection coefficient, and
voltage standing wave ratio (VSWR)
IEC 60512-29- - Connectors for electronic equipment - Tests EN 60512-29-100 -
100 and measurements - Part 29-100: Signal
integrity tests up to 500 MHz on M12 style
connectors - Tests 29a to 29g
IEC 60529 1989 Degrees of protection provided by EN 60529 1991
enclosures (IP Code)
- - + corrigendum 1993
IEC 60603-7 series Connectors for electronic equipment - Part - -
7: Detail specification for 8-way, unshielded,
free and fixed connectors
Publication Year Title EN/HD Year
IEC 60603-7 2008 Connectors for electronic equipment - Part EN 60603-7 2009
7: Detail specification for 8-way, unshielded,
free and fixed connectors
IEC 60603-7-1 2011 Connectors for electronic equipment - Part EN 60603-7-1 2011
7-1: Detail specification for 8-way, shielded,
free and fixed connectors
IEC 60664-1 - Insulation coordination for equipment within EN IEC 60664-1 -
low-voltage supply systems - Part 1:
Principles, requirements and tests
IEC 60998-2-1 - Connecting devices for low-voltage circuits EN 60998-2-1 -
for household and similar purposes - Part 2-
1: Particular requirements for connecting
devices as separate entities with screw-type
clamping units
IEC 60999 series Connecting devices - Electrical copper EN 60999 series
conductors - Safety requirements for screw-
type and screwless-type clamping units
IEC 61076-1 2006 Connectors for electronic equipment - EN 61076-1 2006
Product requirements - Part 1: Generic
specification
IEC 61131-2 - Industrial-process measurement and control - -
- Programmable controllers - Part 2:
Equipment requirements and tests
IEC 61784-5 series Industrial communication networks - Profiles EN 61784-5 series
IEC 61784-5-12 - Industrial communication networks - Profiles EN IEC 61784-5-12 -
- Part 5-12: Installation of fieldbuses -
Installation profiles for CPF 12
IEC 61918 - Industrial communication networks - - -
Installation of communication networks in
industrial premises
IEC 61984 - Connectors - Safety requirements and tests EN 61984 -
IEC 62197-1 - Connectors for electronic equipment - EN 62197-1 -
Quality assessment requirements - Part 1:
Generic specification
IEC 62430 - Environmentally conscious design (ECD) - EN IEC 62430 -
Principles, requirements and guidance
IEC Guide 109 - Environmental aspects - Inclusion in - -
electrotechnical product standards
ISO/IEC TR series Information technology - Generic cabling for - -
11801 customer premises
Publication Year Title EN/HD Year
ISO 1302 - Geometrical Product Specifications (GPS) - EN ISO 1302 -
Indication of surface texture in technical
product documentation
ISO 11469 - Plastics - Generic identification and marking EN ISO 11469 -
of plastics products
TIA-568 SET 2019 Commercial building telecommunications - -
cabling standard set
IEC 61076-2-114 ®
Edition 1.0 2020-07
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Connectors for electrical and electronic equipment – Product requirements –
Part 2-114: Circular connectors – Detail specification for connectors with M8
screw-locking with power contacts and signal contacts for data transmission up
to 100 MHz
Connecteurs pour équipements électriques et électroniques – Exigences de
produit –
Partie 2-114: Connecteurs circulaires – Spécification particulière pour les
connecteurs avec verrouillage à vis M8 avec contacts de puissance et contact
de signaux pour transmission de données jusqu'à 100 MHz
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 31.220.10 ISBN 978-2-8322-8654-8
– 2 – IEC 61076-2-114:2020 © IEC 2020
CONTENTS
FOREWORD . 6
INTRODUCTION . 8
1 Scope . 9
2 Normative references . 9
3 Terms and definitions . 11
4 Technical information . 12
4.1 Systems of levels . 12
4.1.1 Performance levels . 12
4.1.2 Compatibility levels, according to IEC 61076-1 . 12
4.2 Codings . 12
4.3 Classification into climatic categor
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.