EN 61076-2-113:2017
(Main)Connectors for electronic equipment - Product requirements - Part 2-113: Circular connectors - Detail specification for connectors with M12 screw locking with power and signal contacts for data transmission with frequency up to 100 MHz
Connectors for electronic equipment - Product requirements - Part 2-113: Circular connectors - Detail specification for connectors with M12 screw locking with power and signal contacts for data transmission with frequency up to 100 MHz
IEC 61076-2-113:2017 describes M12 circular connectors with two data pairs and power contacts with current ratings up to 12 A, that are typically used for data and power applications in industrial premises. These connectors consist of both fixed and free connectors either rewireable or non rewireable, with screw-locking. Male connectors have round contacts diameters of 1,50 mm, 1,00 mm and 0,60 mm. The different codings provided by this document prevent the mating of accordingly coded male or female connectors to any other similarly sized interfaces covered by other standards and the cross-mating between the different codings provided by this document. M12 is the dimension of the thread of the screw locking mechanism of these circular connectors. Key words: Connectors, Circular Connectors, M12.
Steckverbinder für elektronische Einrichtungen - Produktanforderungen - Teil 2-113: Rundsteckverbinder - Bauartspezifikation für Steckverbinder mit Daten- und Leistungskontakten mit Schraubverriegelung M12 für Frequenzen bis 100 MHz
Connecteurs pour équipements électroniques - Exigences de produit - Partie 2-113: Connecteurs circulaires - Spécification particulière relative aux connecteurs à contacts de puissance et de signalisation, avec verrouillage à vis M12 pour les transmissions de données à des fréquences allant jusqu’à 100 MHz
IEC 61076-2-113:2017 décrit les connecteurs circulaires M12 à deux paires de données et contacts de puissance à courants assignés jusqu’à 12 A, généralement utilisés pour les applications numériques et d’alimentation dans des locaux industriels. Ces connecteurs se composent à la fois d’embases et de fiches, démontables ou non, et sont équipés d’un système à vis. Les connecteurs mâles possèdent des contacts arrondis de 1,50 mm, 1,00 mm et 0,60 mm de diamètre. Les différents codages prévus dans le présent document empêchent l’accouplement de connecteurs mâles ou femelles codés en conséquence avec toute autre interface de même taille faisant l’objet d’autres normes, ainsi que l’accouplement croisé entre les différents codages prévus par le présent document. M12 désigne la dimension du pas de vis du mécanisme de verrouillage à vis de ces connecteurs circulaires. Mots clés: Connecteurs, Connecteurs circulaires, M12
Konektorji za elektronsko opremo - Zahteve za izdelek - 2-113. del: Okrogli konektorji - Podrobna specifikacija za konektorje s podatkovnimi in tokovnimi kontakti z vijačno zaporo M12 za frekvence do 100 MHz (IEC 61076-2-113:2017)
Ta del standarda IEC 61076 opisuje okrogle konektorje M12 z dvema podatkovnima paroma in napajalnimi kontakti z nazivnim tokom največ 12 A, ki se običajno uporabljajo za podatkovne in napajalne potrebe v industrijskem okolju. Ti konektorji so sestavljeni iz pritrjenih in prostih konektorjev z možnostjo ponovnega ožičenja ali brez, z vijačnim zaklepanjem. Moški konektorji imajo okrogle kontakte s premerom 1,50 mm, 1,00 mm in 0,60 mm.
Različne označitve, določene v tem dokumentu, preprečujejo stikanje ustrezno označenih moških ali ženskih konektorjev s katerimi koli drugimi podobno velikimi vmesniki, ki so zajeti v drugih standardih, in navzkrižno stikanje med različnimi označitvami, podanimi v tem dokumentu.
OPOMBA: M12 je dimenzija navoja mehanizma z vijačnim zaklepanjem teh okroglih konektorjev.
General Information
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Connectors for electronic equipment - Product requirements - Part 2-113: Circular connector - Detail specification for connectors with data and power contacts with M12 screw-locking for frequency up to 100MHz (IEC 61076-2-113:2017)31.220.10Plug-and-socket devices. ConnectorsICS:Ta slovenski standard je istoveten z:EN 61076-2-113:2017SIST EN 61076-2-113:2017en01-september-2017SIST EN 61076-2-113:2017SLOVENSKI
STANDARD
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 61076-2-113
June 2017 ICS 31.220.10
English Version
Connectors for electronic equipment - Product requirements - Part 2-113: Circular connectors - Detail specification for connectors with M12 screw locking with power and signal contacts for data transmission with frequency up to 100 MHz (IEC 61076-2-113:2017)
Connecteurs pour équipements électroniques - Exigences de produit - Partie 2-113: Connecteurs circulaires - Spécification particulière relative aux connecteurs à contacts de puissance et de signalisation, avec verrouillage à vis M12 pour les transmissions de données à des fréquences allant jusqu'à 100 MHz (IEC 61076-2-113:2017)
Steckverbinder für elektronische Einrichtungen - Produktanforderungen - Teil 2-113: Rundsteckverbinder - Bauartspezifikation für Steckverbinder mit Daten- und Leistungskontakten mit Schraubverriegelung M12 für Frequenzen bis 100 MHz (IEC 61076-2-113:2017) This European Standard was approved by CENELEC on 2017-03-28. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique Europäisches Komitee für Elektrotechnische Normung CEN-CENELEC Management Centre: Avenue Marnix 17,
B-1000 Brussels © 2017 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN 61076-2-113:2017 E SIST EN 61076-2-113:2017
The following dates are fixed: • latest date by which the document has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2017-12-28 • latest date by which the national standards conflicting with the document have to be withdrawn (dow) 2020-03-28
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CENELEC [and/or CEN] shall not be held responsible for identifying any or all such patent rights.
Endorsement notice The text of the International Standard IEC 61076-2-113:2017 was approved by CENELEC as a European Standard without any modification. SIST EN 61076-2-113:2017
Normative references to international publications with their corresponding European publications
The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.
NOTE 1 When an International Publication has been modified by common modifications, indicated by (mod), the relevant EN/HD applies.
NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is available here: www.cenelec.eu
Publication Year Title EN/HD Year
IEC 60050-581 -
International Electrotechnical Vocabulary (IEV) -
Part 581: Electromechanical components for electronic equipment - -
IEC 60068-1 -
Environmental testing -
Part 1: General and guidance EN 60068-1 -
IEC 60068-2-60 -
Environmental testing -
Part 2-60: Tests - Test Ke: Flowing mixed gas corrosion test EN 60068-2-60 -
IEC 60352 Series
Solderless connections EN 60352 Series
IEC 60512 Series
Connectors for electronic equipment - Tests and measurements EN 60512 Series
IEC 60512-1-2 -
Connectors for electronic equipment - Tests and measurements -
Part 1-2: General examination - Test 1b: Examination of dimension and mass EN 60512-1-2 -
IEC 60512-1-100 -
Connectors for electronic equipment - Tests and measurements -
Part 1-100: General - Applicable publications EN 60512-1-100 -
IEC 60529 -
Degrees of protection provided by enclosures (IP Code) EN 60529 -
IEC 60664-1 -
Insulation coordination for equipment within low-voltage systems -
Part 1: Principles, requirements and tests EN 60664-1 -
IEC 60998-2-1 -
Connecting devices for low-voltage circuits for household and similar purposes -
Part 2-1: Particular requirements for connecting devices as separate entities with screw-type clamping units EN 60998-2-1 -
IEC 60999 Series
Connecting devices - Electrical copper conductors - Safety requirements for screw-type and screwless-type clamping units EN 60999 Series
IEC 61076-1 2006
Connectors for electronic equipment - Product requirements -
Part 1: Generic specification EN 61076-1 2006
IEC 61984 -
Connectors - Safety requirements and tests EN 61984 -
IEC 62197-1 -
Connectors for electronic equipment - Quality assessment requirements -
Part 1: Generic specification EN 62197-1 -
ISO 1302 -
Geometrical Product Specifications (GPS) - Indication of surface texture in technical product documentation EN ISO 1302 -
IEC 61076-2-113 Edition 1.0 2017-02 INTERNATIONAL STANDARD NORME INTERNATIONALE Connectors for electronic equipment – Product requirements –
Part 2-113: Circular connectors – Detail specification for connectors with M12 screw locking with power and signal contacts for data transmission with frequency up to 100 MHz
Connecteurs pour équipements électroniques – Exigences de produit –
Partie 2-113: Connecteurs circulaires – Spécification particulière relative aux connecteurs à contacts de puissance et de signalisation, avec verrouillage à vis M12 pour les transmissions de données à des fréquences allant jusqu’à 100 MHz INTERNATIONAL ELECTROTECHNICAL COMMISSION COMMISSION ELECTROTECHNIQUE INTERNATIONALE
ICS 31.220.10
ISBN 978-2-8322-3883-7
– 2 – IEC 61076-2-113:2017 © IEC 2017 CONTENTS FOREWORD . 5 INTRODUCTION . 7 1 Scope . 9 2 Normative references . 9 3 Terms and definitions . 10 4 Technical information . 10 4.1 Systems of levels . 10 4.1.1 Performance levels . 10 4.1.2 Compatibility levels, according to IEC 61076-1 . 10 4.2 Classification into climatic categories . 10 4.3 Creepage and clearance distances . 10 4.4 Current-carrying capacity . 11 4.5 Marking . 11 4.6 Safety aspects . 11 5 Dimensional information . 11 5.1 General . 11 5.2 Survey of styles and variants . 11 5.2.1 General . 11 5.2.2 Contact terminations . 11 5.2.3 Fixed connectors . 11 5.2.4 Free connectors . 12 5.3 Interface dimensions . 14 5.3.1 Front view Type 1 . 14 5.3.2 Front view Type 2 . 16 5.3.3 Front view Type 3 . 17 5.3.4 Front view Type 4 . 18 5.4 Engagement (mating) information . 19 5.5 Gauges . 19 6 Characteristics . 20 6.1 General . 20 6.2 Pin assignment and other definitions . 20 6.3 Climatic category . 20 6.4 Electrical characteristics . 21 6.4.1 Creepage and clearance distances . 21 6.4.2 Voltage proof . 21 6.4.3 Current-carrying capacity . 22 6.4.4 Contact resistance . 22 6.4.5 Insulation resistance. 22 6.4.6 Impedance . 22 6.5 Transmission characteristics . 22 6.5.1 General . 22 6.5.2 Insertion loss . 22 6.5.3 Return loss . 22 6.5.4 NEXT . 22 6.5.5 FEXT . 23 6.5.6 Transverse conversion loss . 23 SIST EN 61076-2-113:2017
IEC 61076-2-113:2017 © IEC 2017 – 3 –
6.5.7 Transverse conversion transfer loss . 23 6.5.8 Transfer impedance . 23 6.5.9 Input to output resistance . 23 6.5.10 Resistance unbalance. 23 6.6 Mechanical characteristics . 24 6.6.1 Mechanical operation . 24 6.6.2 Effectiveness of connector coupling devices . 24 6.6.3 Insertion and withdrawal forces . 24 6.6.4 Contact retention in insert . 24 6.6.5 Polarizing method . 24 6.7 Other characteristics . 25 6.7.1 Vibration (sinusoidal) . 25 6.7.2 IP degree of
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.