EN 188200:1995
(Main)Sectional Specification: Optical fibres A1 category graded index multimode
- BACK
- 12-Sep-1995
- 14-Jul-1997
- 33.180.10
- CLC/TC 86A
Sectional Specification: Optical fibres A1 category graded index multimode
Superseded by EN 60793-2-10:2002
Rahmenspezifikation: Mehrmoden-Lichtwellenleiter - Kategorie A1
Sectional Specification: Optical fibres A1 category graded index multimode
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Sectional Specification: Optical fibres A1 category graded index multimodeRahmenspezifikation: Mehrmoden-Lichtwellenleiter - Kategorie A1Sectional Specification: Optical fibres A1 category graded index multimode33.180.10Fibres and cablesICS:Ta slovenski
...
This May Also Interest You
IEC 60793-1-41:2024 is available as IEC 60793-1-41:2024 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.IEC 60793-1-41:2024 describes three methods for determining and measuring the modal bandwidth of multimode optical fibres (see IEC 60793-2-10, IEC 60793-2-30, and the IEC 60793‑2‑40 series). The baseband frequency response is directly measured in the frequency domain by determining the fibre response to a sinusoidaly modulated light source. The baseband response can also be measured by observing the broadening of a narrow pulse of light. The calculated response is determined using differential mode delay (DMD) data. The three methods are: Method A – Time domain (pulse distortion) measurement Method B – Frequency-domain measurement Method C – Overfilled launch modal bandwidth calculated from differential mode delay (OMBc) Method A and method B can be performed using one of two launches: an overfilled launch (OFL) condition or a restricted mode launch (RML) condition. Method C is only defined for A1-OM3 to A1-OM5 multimode fibres and uses a weighted summation of DMD launch responses with the weights corresponding to an overfilled launch condition. The relevant test method and launch condition is chosen according to the type of fibre. NOTE 1 These test methods are commonly used in production and research facilities and are not easily accomplished in the field. NOTE 2 OFL has been used for the modal bandwidth value for LED-based applications for many years. However, no single launch condition is representative of the laser (e.g. VCSEL) sources that are used for gigabit and higher rate transmission. This fact drove the development of IEC 60793-1-49 for determining the effective modal bandwidth of laser optimized 50 µm fibres. See IEC 60793-2-10 and IEC 61280-4-1 for more information. This fourth edition cancels and replaces the third edition published in 2010. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: a) the addition of a direct reference for method A and method B.
- Standard33 pagesEnglish languagesale 10% offe-Library read for×1 day
- Draft28 pagesEnglish languagesale 10% offe-Library read for×1 day
- 30-May-2024
- 33.180.10
- CLC/TC 86A
IEC 60793-1-45:2024 is available as IEC 60793-1-45:2024 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.IEC 60793-1-45:2024 establishes uniform requirements for measuring the mode field diameter (MFD) of single-mode optical fibre, thereby assisting in the inspection of fibres and cables for commercial purposes. This third edition cancels and replaces the second edition published in 2017. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: a) modification of the minimum distance between the fibre end and the detector for the direct far field scan (Annex A). b) generalization of the requirement for the minimum dynamic range for all fibre types (Annex A).
- Standard34 pagesEnglish languagesale 10% offe-Library read for×1 day
- Draft30 pagesEnglish languagesale 10% offe-Library read for×1 day
- 30-May-2024
- 33.180.10
- CLC/TC 86A
IEC 60794-1-217:2024 series defines the test procedure to measure the permanent fibre protrusion compared to the cable elements and cable sheath due to thermal exposure of a cable. This document partially replaces IEC 60794‑1‑22:2017. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to IEC 60794‑1‑22:2017: a) added clarification in the objective that the purpose of this test procedure is to measure the permanent fibre protrusion of cables without rigid strength members; b) replaced the reference to method F1 for the apparatus with a detailed description for the temperature chamber and temperature sensing device as done in IEC 60794-1-211; c) added a measuring device in the subclause for apparatus; d) added conditioning before cutting the cable sample as done in IEC 60794-1-211 e) added all required steps in the subclause for temperature cycling as well as the table for the minimum soak time and the figure for the cycle procedure, and removed the reference to IEC 60794-1-22, method F1; f) improved the figures and added a figure for preparation of the cable sample; g) added the informative Annex A for the test procedure recommended for cables with rigid strength members.
- Standard21 pagesEnglish languagesale 10% offe-Library read for×1 day
- Draft11 pagesEnglish languagesale 10% offe-Library read for×1 day
- Draft17 pagesEnglish languagesale 10% offe-Library read for×1 day
- 23-May-2024
- 33.180.10
- CLC/TC 86A
IEC 60794-1-212:2024 defines the test procedure to examine the attenuation behaviour (change in attenuation) when an optical fibre cable with cable elements fixed at both ends is subjected to temperature cycling. This test assesses the attenuation behaviour of a cable under a no-end movement condition intended for termination with, for example, interconnecting devices or passive components. This document partially cancels and replaces IEC 60794-1-22:2017. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to IEC 60794-1-22:2017: a) the description of the test method has been changed to “with cable elements fixed at both ends”; b) subclauses have been added to the procedure clause; c) the preparation of cable sample and test set-up has been arranged in a logical way; d) Figure 1 has been added for illustration of the preparation of cable sample, DUT and test set-up; e) the temperature chamber temperature tolerance has been changed to ± 3 °C as done in IEC 60794‑1‑22, method F1; f) all required steps have been added to the subclause for temperature cycling as well as the table for the minimum soak time and the figure for the cycle procedure, and removed the reference to IEC 60794-1-22, method F1; g) the maximum change in attenuation has been added to the details to be specified; h) a new subclause 4.5 has been added for details to be reported.
- Standard14 pagesEnglish languagesale 10% offe-Library read for×1 day
- Draft9 pagesEnglish languagesale 10% offe-Library read for×1 day
- Draft11 pagesEnglish languagesale 10% offe-Library read for×1 day
- 23-May-2024
- 33.180.10
- CLC/TC 86A
IEC 60794-2-23: 2024 is a detail specification and specifies indoor multi-fibre cables for use in MPO (multi-fibre push on) connector terminated cable assemblies.
- Standard19 pagesEnglish languagesale 10% offe-Library read for×1 day
- 14-Mar-2024
- 33.180.10
- CLC/TC 86A
IEC 60794-1-311:2024 describes test procedures to be used in establishing uniform requirements of optical fibre cable elements for the mechanical property – tensile strength and elongation at break. This document applies to optical fibre cables for use with telecommunication equipment and devices employing similar techniques, and to cables having a combination of both optical fibres and electrical conductors. Throughout the document, the wording "optical cable" can also include optical fibre units, microduct fibre units, etc. This document partially cancels and replaces IEC 60794-1-23:2019. This edition includes the following significant technical changes with respect to IEC 60794‑1‑23:2019: a) The information about dumb-bells is removed because this is not used for testing cable elements; b) the parameters strain at yield and E modulus are added in 5.7.
- Standard14 pagesEnglish languagesale 10% offe-Library read for×1 day
- 14-Mar-2024
- 33.180.10
- CLC/TC 86A
IEC 60794-1-312: 2024 describes test procedures to be used in establishing uniform requirements of optical fibre cable elements for the mechanical property – tensile strength and elongation at low temperature. This document applies to optical fibre cables for use with telecommunication equipment and devices employing similar techniques, and to cables having a combination of both optical fibres and electrical conductors. Throughout the document, the wording "optical cable" can also include optical fibre units, microduct fibre units, etc. This document partially cancels and replaces method G11B of IEC 60794-1-23:2019. This edition includes the following significant technical changes with respect to IEC 60794‑1‑23:2019: a) alignment of the title with the content of the method.
- Standard17 pagesEnglish languagesale 10% offe-Library read for×1 day
- 14-Mar-2024
- 33.180.10
- CLC/TC 86A
IEC 60794-2-24:2024 is a detail specification and specifies indoor multiple multi-fibre unit cables for use in MPO (multi-fibre push on) connector terminated breakout cable assemblies.
- Standard21 pagesEnglish languagesale 10% offe-Library read for×1 day
- 07-Mar-2024
- 33.180.10
- CLC/TC 86A
IEC 60794-1-306: 2023 describes test procedures to verify the mechanical and functional integrity of the fibre ribbon structure. The test determines the capability of the ribbon to withstand torsion without delamination between optical fibre and ribbon bonding agent. This document applies to optical fibre ribbons in optical cables for use with telecommunication equipment and devices employing similar techniques, and to optical fibre ribbons in cables having a combination of both optical fibres and electrical conductors. This document is not applicable to partially-bonded ribbons. The method for partially-bonded ribbons is under consideration. Throughout the document, the wording "optical cable" can also include optical fibre units, microduct fibre units, etc. NOTE The environmental testing of optical fibre ribbon would be valuable for some applications. Useful information about suitable test methods can be found in the optical fibre standards IEC 60793-1-50, IEC 60793-1-51, IEC 60793‑1‑52, and IEC 60793-1-53. This document partially cancels and replaces IEC 60794‑1‑23:2019. This edition includes the following significant technical changes with respect to IEC 60794‑1‑23:2019: a) change the scope, not include partially-bonded ribbon; b) add some details to the procedure.
- Standard12 pagesEnglish languagesale 10% offe-Library read for×1 day
- 26-Oct-2023
- 33.180.10
- CLC/TC 86A
IEC 60794-1-111: 2023 defines the test procedure to determine the ability of an optical fibre cable to withstand bending around a test mandrel. The primary purpose of this procedure is to measure the change in attenuation when the cable is bent around a test mandrel. A secondary purpose is to assess whether the cable has been physically damaged by bending. NOTE 1 This test can be utilized at any specified temperature, including the low or high temperature limits for the cable. NOTE 2 The bend test procedure for cable elements is specified in IEC 60794-1-301, method G1. This document partially cancels and replaces IEC 60794-1-21:2015. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to IEC 60794‑1‑21:2015: a) the nominal sample length was newly specified as 10 m between the cable element fixing points at both ends, unless otherwise specified; b) the number of turns on the mandrel in Figure 1 for the single-helix configuration were corrected to match the number of turns shown in the figure for the two-helix configuration; c) requirements on the turnaround loop were added for method E11A, two-helix configuration; d) the turnaround loop with the same diameter as the mandrel was taken into account for calculation of the number of turns of each helix for method E11A, two-helix configuration; e) added a formula for calculation of the number of revolutions in each helix for method E11A, two-helix configuration; f) added a description for the procedure when the turnaround loop diameter is larger than the mandrel diameter for method E11A, two-helix configuration; g) all the figures were updated and the different components labelled; h) added the attenuation monitoring equipment in 4.2 for the apparatus and the description to measure the change in attenuation in the test methods E11A and E11B; i) added Clause 9 for details to be reported; j) added Annex A showing an example of a special mandrel to perform the bend test according to method E11A, two-helix configuration; k) added Annex B providing the rationale for the options of method E11A, two-helix configuration.
- Standard22 pagesEnglish languagesale 10% offe-Library read for×1 day
- Draft18 pagesEnglish languagesale 10% offe-Library read for×1 day
- 26-Oct-2023
- 33.180.10
- CLC/TC 86A
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.