EN 60034-28:2007

Rotating electrical machines - Part 28: Test methods for determining quantities of equivalent circuit diagrams for three-phase low-voltage cage induction motors

Applies to three-phase low-voltage cage induction motors of frame numbers 56 to 400 as specified in IEC 60072-1. Establishes procedures to obtain values for elements of single phase equivalent circuit diagrams from tests and defines standard elements of these diagrams.

Drehende elektrische Maschinen - Teil 28: Prüfverfahren zur Bestimmung der Größen in Ersatzschaltbildern dreiphasiger Niederspannungs-Kurzschlussläufer-Induktionsmotoren

Machines électriques tournantes - Partie 28: Méthodes d'essai pour la détermination des grandeurs des schémas d'équivalence des circuits pour moteurs à induction à cage basse tension triphasés

S'applique aux moteurs à induction à cage basse tension triphasés de désignations de carcasses entre 56 et 400, spécifiés dans la CEI 60072-1. Définit des éléments normalisés de schémas de circuits équivalents monophasés et établit à partir d'essais des procédures pour obtenir des valeurs pour ces éléments.

Električni rotacijski stroji - 28. del: Preskušalne metode za ugotavljanje veličin nadomestnih shem trifaznih nizkonapetostnih motorjev z indukcijsko kletko (IEC 60034-28:2007)

General Information

• Status: Withdrawn
• Publication Date: 15-May-2007
• Withdrawal Date: 30-Apr-2010
• ICS: 29.160 - Rotating machinery
• Technical Committee: CLC/TC 2 - Rotating machinery
• Drafting Committee: IEC/TC 2 - IEC_TC_2
• Parallel Committee: IEC/TC 2 - IEC_TC_2
• Current Stage: 9960 - Withdrawal effective - Withdrawal
• Start Date: 17-Jan-2016
• Completion Date: 17-Jan-2016
• Ref Project: SIST EN 60034-28:2007 - Rotating electrical machines - Part 28: Test methods for determining quantities of equivalent circuit diagrams for three-phase low-voltage cage induction motors (IEC 60034-28:2007)

Relations

• Replaced By: EN 60034-28:2013 - Rotating electrical machines - Part 28: Test methods for determining quantities of equivalent circuit diagrams for three-phase low-voltage cage induction motors
• Effective Date: 29-Jan-2023

Standards Content (Sample)

SLOVENSKI STANDARD
01-november-2007
(OHNWULþQLURWDFLMVNLVWURMLGHO3UHVNXãDOQHPHWRGH]DXJRWDYOMDQMHYHOLþLQ
QDGRPHVWQLKVKHPWULID]QLKQL]NRQDSHWRVWQLKPRWRUMHY]LQGXNFLMVNRNOHWNR,(&

Rotating electrical machines - Part 28: Test methods for determining quantities of
equivalent circuit diagrams for three-phase low-voltage cage induction motors (IEC
60034-28:2007)
Drehende elektrische Maschinen - Teil 28: Prüfverfahren zur Bestimmung der Größen in
Ersatzschaltbildern dreiphasiger Niederspannungs-Kurzschlussläufer-Induktionsmotoren
(IEC 60034-28:2007)
Machines électriques tournantes - Partie 28: Méthodes d'essai pour la détermination des
grandeurs des schémas d'équivalence des circuits pour moteurs à induction à cage
basse tension triphasés (CEI 60034-28:2007)
Ta slovenski standard je istoveten z: EN 60034-28:2007
ICS:
29.160.30 Motorji Motors
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
EN 60034-28
NORME EUROPÉENNE
May 2007
EUROPÄISCHE NORM
ICS 29.160
English version
Rotating electrical machines -
Part 28: Test methods for determining quantities
of equivalent circuit diagrams
for three-phase low-voltage cage induction motors
(IEC 60034-28:2007)
Machines électriques tournantes -  Drehende elektrische Maschinen -
Partie 28: Méthodes d'essai Teil 28: Prüfverfahren
pour la détermination des grandeurs zur Bestimmung der Größen
des schémas d'équivalence des circuits in Ersatzschaltbildern dreiphasiger
pour moteurs à induction Niederspannungs-Kurzschlussläufer-
à cage basse tension triphasés Induktionsmotoren
(CEI 60034-28:2007) (IEC 60034-28:2007)

This European Standard was approved by CENELEC on 2007-05-01. CENELEC members are bound to comply
with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard
the status of a national standard without any alteration.

Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the Central Secretariat or to any CENELEC member.

This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and notified
to the Central Secretariat has the same status as the official versions.

CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Cyprus, the
Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.

CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung

Central Secretariat: rue de Stassart 35, B - 1050 Brussels

© 2007 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 60034-28:2007 E
Foreword
The text of document 2/1415/FDIS, future edition 1 of IEC 60034-28, prepared by IEC TC 2, Rotating
machinery, was submitted to the IEC-CENELEC parallel vote and was approved by CENELEC as
EN 60034-28 on 2007-05-01.
The following dates were fixed:
– latest date by which the EN has to be implemented
at national level by publication of an identical
national standard or by endorsement (dop) 2008-02-01
– latest date by which the national standards conflicting
with the EN have to be withdrawn (dow) 2010-05-01
Annex ZA has been added by CENELEC.
__________
Endorsement notice
The text of the International Standard IEC 60034-28:2007 was approved by CENELEC as a European
Standard without any modification.
__________
- 3 - EN 60034-28:2007
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications

The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.

NOTE  When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD
applies.
Publication Year Title EN/HD Year

1) 2)
IEC 60034-1 - Rotating electrical machines - EN 60034-1 2004
Part 1: Rating and performance

IEC 60044 Series Instrument transformers EN 60044 Series

1) 2)
IEC 60051-1 - Direct acting indicating analogue electrical EN 60051-1 1998
measuring instruments and their
accessories -
Part 1: Definitions and general requirements
common to all parts
1)
IEC 60072-1 - Dimensions and output series for rotating - -
electrical machines -
Part 1: Frame numbers 56 to 400 and flange
numbers 55 to 1 080
1)
Undated reference.
2)
Valid edition at date of issue.

NORME CEI
INTERNATIONALE
IEC
60034-28
INTERNATIONAL
Première édition
STANDARD
First edition
2007-03
Machines électriques tournantes –
Partie 28:
Méthodes d’essai pour la détermination des
grandeurs des schémas d’équivalence des
circuits pour moteurs à induction à cage
basse tension triphasés
Rotating electrical machines –
Part 28:
Test methods for determining quantities of
equivalent circuit diagrams for three-phase
low-voltage cage induction motors
© IEC 2007 Droits de reproduction réservés ⎯ Copyright - all rights reserved
Aucune partie de cette publication ne peut être reproduite ni No part of this publication may be reproduced or utilized in any
utilisée sous quelque forme que ce soit et par aucun procédé, form or by any means, electronic or mechanical, including
électronique ou mécanique, y compris la photocopie et les photocopying and microfilm, without permission in writing from
microfilms, sans l'accord écrit de l'éditeur. the publisher.
International Electrotechnical Commission, 3, rue de Varembé, PO Box 131, CH-1211 Geneva 20, Switzerland
Telephone: [phone] Telefax: [phone] E-mail: [e-mail] Web: www.iec.ch
CODE PRIX
U
PRICE CODE
Commission Electrotechnique Internationale
International Electrotechnical Commission
МеждународнаяЭлектротехническаяКомиссия
Pour prix, voir catalogue en vigueur
For price, see current catalogue

60034-28 © IEC:2007 – 3 –
CONTENTS
FOREWORD.5
INTRODUCTION.9

1 Scope.11
2 Normative references .11
3 Terms, definitions and symbols .11
3.1 Symbols .11
3.2 Equivalent Y-connection.17
4 Test requirements .17
4.1 Frequency and voltage .17
4.2 Instrumentation .17
5 Approximations and uncertainties .19
6 Test procedures .19
6.1 General .19
6.2 Stator d.c. line-to-line resistance measurement .21
6.3 Load-test.21
6.4 No-load test.21
6.5 Reverse rotation and locked rotor tests .23
7 Determination of motor quantities .23
7.1 General .23
7.2 Resistance of stator winding R .27
s
7.3 Equivalent resistance of iron losses R .27
fe
7.4 Total stator inductance L = L + L .29
ts m s
7.5 Total leakage inductance L .33
σ
7.6 Magnetizing inductance L and voltage U .37
m m
7.7 Stator and rotor leakage inductances L and L ’ .37
s r
7.8 Inductances for calculations at constant flux (rated load).37
7.9 Resistance of rotor cage R ’ referred to stator winding.39
r
Annex A (informative) Form for calculation of resistance of iron losses R .43
fe
Annex B (informative) Form for calculation of total stator inductance L .45
ts
Annex C (informative) Form for calculation of total leakage inductance L .47
σ
Annex D (informative) Form for calculation of magnetizing inductance L .49
m
Annex E (informative) Sample calculation .51

Figure 1 – Type-T equivalent circuit diagram .25
Figure 2 – Type-T equivalent circuit diagram (iron losses disregarded) .25
Figure 3 – Type-L equivalent circuit diagram (iron losses disregarded) .25
Figure 4 – Typical characteristic of inductance L over current I .31

60034-28 © IEC:2007 – 5 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
___________
ROTATING ELECTRICAL MACHINES –

Part 28: Test methods for determining quantities of equivalent circuit
diagrams for three-phase low-voltage cage induction motors

FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any
equipment declared to be in conformity with an IEC Publication.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held re
...