EN 61076-4-115:2003

Connectors for electronic equipment - Part 4-115: Printed board connectors - Backplane connector for InfiniBand equipment

Describes a single-part hybrid connector, with a section for high-speed on a 3 mm grid and a low-speed section with power and ground connections on a 2 mm grid, for printed boards and backplanes in accordance with EN 60917-2-2

Steckverbinder für elektronische Einrichtungen - Teil 4-115: Steckverbinder für gedruckte Schaltungen - Rückplatten-Steckverbinder für InfiniBand-Geräte

Connecteurs pour équipements électroniques - Partie 4-115: Connecteurs pour cartes imprimées - Connecteur de fond de panier pour équipement InfiniBand

Décrit un connecteur hybride en une partie, avec une section pour connexions à débits élevés au pas de 3 mm et une section à bas débits avec contacts de puissance et continuité de masse au pas de 2 mm, pour cartes imprimées et fonds de panier selon la EN 60917-2-2

Konektorji za elektronsko opremo - 4-115. del: Konektorji za tiskane plošče - Konektorji za hrbtne plošče za opremo InfiniBand (IEC 61076-4-115:2003)

General Information

• Status: Published
• Publication Date: 27-Aug-2003
• Withdrawal Date: 30-Apr-2006
• ICS: 31.220.10 - Plug-and-socket devices. Connectors
• Technical Committee: CLC/SR 48B - Connectors
• Drafting Committee: IEC/SC 48B - IEC_SC_48B
• Parallel Committee: IEC/SC 48B - IEC_SC_48B
• Current Stage: 6060 - Document made available - Publishing
• Start Date: 28-Aug-2003
• Completion Date: 28-Aug-2003
• Ref Project: SIST EN 61076-4-115:2004 - Connectors for electronic equipment -- Part 4-115: Printed board connectors - Backplane connector for InfiniBand equipment

Standards Content (Sample)

SLOVENSKI SIST EN 61076-4-115:2004

STANDARD
november 2004
Konektorji za elektronsko opremo - 4-115. del: Konektorji za tiskane plošče -
Konektorji za hrbtne plošče za opremo InfiniBand (IEC 61076-4-115:2003)
Connectors for electronic equipment - Part 4-115: Printed board connectors -
Backplane connectors for InfiniBand equipment (IEC 61076-4-115:2003)
ICS 31.220.10 Referenčna številka
©  Standard je založil in izdal Slovenski inštitut za standardizacijo. Razmnoževanje ali kopiranje celote ali delov tega dokumenta ni dovoljeno

EUROPEAN STANDARD EN 61076-4-115
NORME EUROPÉENNE
EUROPÄISCHE NORM August 2003
ICS 31.220.10
English version
Connectors for electronic equipment
Part 4-115: Printed board connectors –
Backplane connector for InfiniBand equipment
(IEC 61076-4-115:2003)
Connecteurs pour équipements Steckverbinder für elektronische
électroniques Einrichtungen
Partie 4-115: Connecteurs pour cartes Teil 4-115: Steckverbinder für gedruckte
imprimées – Schaltungen –
Connecteur de fond de panier pour Rückplatten-Steckverbinder für
équipement InfiniBand InfiniBand-Geräte
(CEI 61076-4-115:2003) (IEC 61076-4-115:2003)

This European Standard was approved by CENELEC on 2003-05-01. CENELEC members are bound to
comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration.

Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the Central Secretariat or to any CENELEC member.

This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and
notified to the Central Secretariat has the same status as the official versions.

CENELEC members are the national electrotechnical committees of Austria, Belgium, Czech Republic,
Denmark, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Portugal, Slovakia, Spain, Sweden, Switzerland and United Kingdom.

CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung

Central Secretariat: rue de Stassart 35, B - 1050 Brussels

© 2003 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.

Ref. No. EN 61076-4-115:2003 E

Foreword
The text of document 48B/1288/FDIS, future edition 1 of IEC 61076-4-115, prepared by SC 48B,
Connectors, of IEC TC 48, Electromechanical components and mechanical structures for electronic
equipment, was submitted to the IEC-CENELEC parallel vote and was approved by CENELEC as
EN 61076-4-115 on 2003-05-01.
The following dates were fixed:
– latest date by which the EN has to be implemented
at national level by publication of an identical
national standard or by endorsement (dop) 2004-03-01
– latest date by which the national standards conflicting
with the EN have to be withdrawn (dow) 2006-05-01
The International Electrotechnical Commission (IEC) and CENELEC draw attention to the fact that it is
claimed that compliance with this document may involve the use of a patent concerning
a) an electrical connector assembly for establishing electrical contact with contacting devices of
external terminals, e.g. with solder points of a circuit board;
b) an electrical connector assembly for establishing electrical contact with external terminals having
contacting devices with contact faces, e.g. with solder points of a circuit board;
c) an electrical connector assembly with an electrical connector having a connecting position and
contacting devices for establishing electrical contact between a first and a second printed circuit
board.
The IEC and CENELEC take no position concerning the evidence, validity and scope of this patent
right.
The holder of this patent right has assured the IEC that he/she is willing to negotiate licences under
reasonable and non-discriminatory terms and conditions with applicants throughout the world. In this
respect, the statement of the holder of this patent right is registered with the IEC. Information may be
obtained from:
Tyco Electronics Cororation
PO Box 3608
Harrisburg, PA 17105-3608
USA
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights other than those identified above. IEC and CENELEC shall not be held responsible for
identifying any or all such patent rights.
Annexes designated "normative" are part of the body of the standard.
In this standard, annexes A, B and ZA are normative.
Annex ZA has been added by CENELEC.
__________
Endorsement notice
The text of the International Standard IEC 61076-4-115:2003 was approved by CENELEC as a
European Standard without any modification.
__________
- 3 - EN 61076-4-115:2003
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
This European Standard incorporates by dated or undated reference, provisions from other
publications. These normative references are cited at the appropriate places in the text and the
publications are listed hereafter. For dated references, subsequent amendments to or revisions of any
of these publications apply to this European Standard only when incorporated in it by amendment or
revision. For undated references the latest edition of the publication referred to applies (including
amendments).
NOTE When an international publication has been modified by common modifications, indicated by (mod), the relevant
EN/HD applies.
Publication Year Title EN/HD Year
1)
IEC 60068-1 1988 Environmental testing EN 60068-1 1994
Part 1: General and guidance
IEC 60352-5 2001 Solderless connections EN 60352-5 2001
Part 5: Press-in connections - General
requirements, test methods and
practical guidance
IEC 60512 Series Connectors for electronic equipment - EN 60512 Series
Tests and measurements
Part 1: General
IEC 60512-1-100 2001 Connectors for electronic equipment - EN 60512-1-100 2001
Tests and measurements
Part 1-100: General - Applicable
publications
IEC 60917-2-2 1994 Modular order for the development of EN 60917-2-2 1996
mechanical structures for electronic
equipment practices
Part 2: Sectional specification -
Interface co-ordination dimensions for
the 25 mm equipment practice --
Section 2: Detail specification -
Dimensions for subracks, chassis,
backplanes, front panels and plug-in
units
IEC 61076-1 1995 Connectors with assessed quality, for EN 61076-1 1995
use in d.c., low frequency analogue and
in digital high-speed data applications
Part 1: Generic specification
IEC 61076-4 1995 Part 4: Sectional specification - Printed EN 61076-4 1996
board connectors
1)
EN 60068-1 includes corrigendum October 1998 + A1:1992 to IEC 60068-1.

Publication Year Title EN/HD Year
IEC 61076-4-001 1996 Part 4: Printed board connectors -- EN 61076-4-001 1996
Section 001: Blank detail specification

ISO 1302 2002 Geometrical Product Specifications EN ISO 1302 2002
(GPS) - Indication of surface texture in
technical product documentation

NORME CEI
INTERNATIONALE IEC
61076-4-115
INTERNATIONAL
Première édition
STANDARD
First edition
2003-02
Connecteurs pour équipements électroniques –
Partie 4-115:
Connecteurs pour cartes imprimées –
Connecteur de fond de panier
pour équipement InfiniBand
Connectors for electronic equipment –
Part 4-115:
Printed board connectors –
Backplane connector
for InfiniBand equipment
 IEC 2003 Droits de reproduction réservés  Copyright - all rights reserved
Aucune partie de cette publication ne peut être reproduite ni No part of this publication may be reproduced or utilized in any
utilisée sous quelque forme que ce soit et par aucun procédé, form or by any means, electronic or mechanical, including
électronique ou mécanique, y compris la photocopie et les photocopying and microfilm, without permission in writing from
microfilms, sans l'accord écrit de l'éditeur. the publisher.
International Electrotechnical Commission, 3, rue de Varembé, PO Box 131, CH-1211 Geneva 20, Switzerland
Telephone: [phone] Telefax: [phone] E-mail: [e-mail]  Web: www.iec.ch
CODE PRIX
XB
Commission Electrotechnique Internationale PRICE CODE
International Electrotechnical Commission
Международная Электротехническая Комиссия
Pour prix, voir catalogue en vigueur
For price, see current catalogue

61076-4-115  IEC:2003 – 3 –
CONTENTS
FOREWORD . 9
1 General data .15
1.1 Recommended method of mounting .15
1.2 Ratings and characteristics .17
1.3 Normative references.19
1.4 Marking .21
1.5 IEC type designation .21
1.6 Ordering information .21
2 Technical data .23
2.1 Definitions .23
2.2 Survey of styles and variants.25
2.3 Information on application .27
3 Dimensional information.35
3.1 General .35
3.2 Isometric view and common features.37
3.3 Mating information .43
3.4 Fixed connector .49
3.5 Plug-in card paddle .51
3.6 Mounting information for fixed connector .55
3.7 Mounting information for paddle-guard .57
3.8 Gauges.61
4 Characteristics.71
4.1 Climatic category .71
4.2 Electrical.71
4.3 Mechanical .77
4.4 High-speed characteristics .81
5 Test schedule .87
5.1 General .87
5.2 Test schedule tables .101
Annex A (normative) Test method for gauge supporting force .125
A.1 Object .125
A.2 Preparation of the specimen .125
A.3 Test equipment .125
A.4 Test method.125
A.5 Details to be specified .129
Annex B (normative) Test method for dust and fibre resistance.131
B.1 Object .131
B.2 Preparation of the specimen .131
B.3 Test equipment .131
B.4 Test method.133

61076-4-115  IEC:2003 – 5 –
Figure 1 – Press-in/compression method of mounting .15
Figure 2 – Example of a paddle-guard, to be mounted on the plug-in card paddle.27
Figure 3 – Designation of contacts on backplane for press-in/compression mounting .29
Figure 4 – Designation of contacts on component side.31
Figure 5 – Designation of contacts on solder side .31
Figure 6 – Low-speed section – Apertures in paddle-guard control engaging sequence .33
Figure 7 – Co-ordination dimensions.
...