EN 61400-22:2011/AC:2020-04
(Corrigendum)Wind turbines - Part 22: Conformity testing and certification
Wind turbines - Part 22: Conformity testing and certification
TC - 2020-03-23: corrigendum created to confirm EN 61400-22:2011 and is not the result of a mistake (see BT decision D165/C016)
Windenergieanlagen - Teil 22: Konformitätsprüfung und Zertifizierung
Eoliennes - Partie 22: Essais de conformité et certification
Vetrne turbine - 22. del: Preskušanje skladnosti in certificiranje - Popravek AC
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 61400-22:2011/AC:2020
01-julij-2020
Vetrne turbine - 22. del: Preskušanje skladnosti in certificiranje - Popravek AC
Wind turbines - Part 22: Conformity testing and certification
Windenergieanlagen - Teil 22: Konformitätsprüfung und Zertifizierung
Eoliennes - Partie 22: Essais de conformité et certification
Ta slovenski standard je istoveten z: EN 61400-22:2011/AC:2020-04
ICS:
03.120.20 Certificiranje proizvodov in Product and company
podjetij. Ugotavljanje certification. Conformity
skladnosti assessment
27.180 Vetrne elektrarne Wind turbine energy systems
SIST EN 61400-22:2011/AC:2020 en,fr
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega st
...
This May Also Interest You
- Corrigendum4 pagesEnglish languagesale 10% offe-Library read for×1 day
IEC 61400-21-2 - Wind energy generation systems - Measurement and assessment of electrical characteristics - Wind power plants - has the following scope: IEC 61400-21-2 defines and specifies the quantities that shall be determined to characterize the electrical characteristics of grid-connected power plants (PP). IEC 61400-21-2 defines the measurement and test procedures for quantifying the electrical characteristics as basis for the verification of compliance of PP, including: - Power quality aspects - Steady state operation - Dynamic response (undervoltage and overvoltage fault ride-through) - Disconnection from grid (Grid protection) - Control performance IEC 61400-21-2 defines a uniform functionality test and measurement procedure for the power plant controller (PPC), as a basis for the unit test of the power plant controller. IEC 61400-21-2 defines the procedures for assessing compliance with electrical connection requirements, including the aggregation methods for power quality aspects such as voltage variations, flicker, harmonics and interharmonics. IEC 61400-21-2 defines the procedures for measurement and fault recording for the verification of power plant electrical simulation models in relation to undervoltage and overvoltage ride through events. These measurement procedures are valid for power plants, including the power plant controller and other connected equipment, necessary for the operation of the Power Plant. The measurement procedures are valid for any size of power plant connected to the point of connection (POC) at one connection point. The procedures for assessing and verifying the compliance with grid connection requirements are valid for power plants in power systems with fixed frequency and a sufficient short-circuit power. Out of the scope of this standard are: - Multi park control, i.e. cluster management of several power plants (PP) or several connection points - Compliance test and performance requirements, including pass or fail criteria - Specific component test and validation of the PP equipment (switchgear, cables, transformers, etc.), which are covered by other IEC standards - Wind power plant model validation, as defined in the IEC 61400-27-2 - Load flow calculation methods and load flow study guidelines - Test and measurement of the communication interface and system of the PP as defined in the IEC 61400-25 series NOTE For the purposes of this document, the following terms for system voltage apply, based on IEC 60038 Low voltage (LV) refers to 100 V 230 kV
- Standard151 pagesEnglish languagesale 10% offe-Library read for×1 day
IEC 61400-50-1:2022 specifies methods and requirements for the application of instruments to measure wind speed (and related parameters, e.g. wind direction, turbulence intensity). Such measurements are required as an input to some of the evaluation and testing procedures for wind energy and wind turbine technology (e.g. resource evaluation and turbine performance testing) described by other standards in the IEC 61400 series. This document is applicable specifically to the use of wind measurement instruments mounted on meteorological masts, turbine nacelles or turbine spinners which measure the wind at the location at which the instruments are mounted. This document excludes remote sensing devices which measure the wind at some location distant from the location at which the instrument is mounted (e.g. vertical profile or forward facing lidars).
- Standard82 pagesEnglish languagesale 10% offe-Library read for×1 day
IEC 61400-12-1:2022 specifies a procedure for measuring the power performance characteristics of a single wind turbine and applies to the testing of wind turbines of all types and sizes connected to the electrical power network. In addition, this document defines a procedure to be used to determine the power performance characteristics of small wind turbines (as defined in IEC 61400-2) when connected to either the electric power network or a battery bank. This document defines a measurement methodology that requires the measured power curve and derived energy production figures to be supplemented by an assessment of uncertainty sources and their combined effects. This third edition of IEC 61400-12-1 is part of a structural revision that cancels and replaces the performance standards IEC 61400-12-1:2017 and IEC 61400-12-2:2013. The structural revision contains no technical changes with respect to IEC 61400-12-1:2017 and IEC 61400‑12‑2:2013, but the parts that relate to wind measurements, measurement of site calibration and assessment of obstacle and terrain have been extracted into separate standards.
- Standard157 pagesEnglish languagesale 10% offe-Library read for×1 day
IEC 61400-12-2:2022 specifies a procedure for verifying the power performance characteristics of a single electricity-producing, horizontal axis wind turbine that is not considered to be a small wind turbine per IEC 61400-2. It is expected that this document be used when the specific operational or contractual specifications do not comply with the requirements set out in IEC 61400-12-1. The purpose of this document is to provide a uniform methodology of measurement, analysis, and reporting of power performance characteristics for individual electricity producing wind turbines utilising nacelle-anemometry methods. This document is intended to be applied only to horizontal axis wind turbines of sufficient size that the nacelle-mounted anemometer does not significantly affect the flow through the turbine’s rotor and around the nacelle and hence does not affect the wind turbine’s performance. This second edition of IEC 61400-12-2 is part of a structural revision that cancels and replaces the performance standards IEC 61400-12-1:2017 and IEC 61400-12-2:2013. The structural revision contains no technical changes with respect to IEC 61400-12-1:2017 and IEC 61400‑12‑2:2013, but the parts that relate to wind measurements, measurement of site calibration and assessment of obstacle and terrain have been extracted into separate standards.
- Standard81 pagesEnglish languagesale 10% offe-Library read for×1 day
The IEC 61400 series of standards addresses wind energy generation technical requirements up to the point of interconnection with the utility grid system. Part 12 of the IEC 61400 series of standards comprises a sub-set of standards which are to be used in the evaluation and measurement of the power performance characteristics of wind turbines. The power performance characterisation of wind turbines of all types and sizes is covered. Wind turbine power performance characteristics are determined from a measured power curve and an associated estimated annual energy production (AEP) and its uncertainty. The measured power curve, defined as the relationship between the wind speed and the wind turbine power output, is determined by collecting simultaneous measurements of meteorological variables (including wind speed), as well as wind turbine signals (including power output) at the test site for a period that is long enough to establish a statistically significant database over a range of wind speeds and under varying wind and atmospheric conditions. The AEP is calculated by applying the measured power curve to reference wind speed frequency distributions, assuming 100 % availability. Part 12-0 provides a general introduction to the available options for power performance measurement and the contributing evaluations which are further detailed in the other parts of the IEC 61400-12 series. Although the -12 series also defines the specifications of the meteorological variables (and in particular wind speed) required for the power performance evaluation, the methods and procedures for measuring or otherwise acquiring the wind speed data are defined in the IEC 61400-50 wind measurement series of standards. The evaluation of the wind turbine power performance characteristic according to this series of standards requires the measured power curve and derived energy production figures to be supplemented by an assessment of uncertainty sources and their combined effects. The basis of the uncertainty assessment is ISO/IEC Guide 98-3. The wind measurement uncertainty sources shall be identified and quantified from procedures described in the relevant wind measurement standards contained in the IEC 61400-50 series. The wind measurement uncertainties shall be propagated through to and combined with the other sources of uncertainty in the power curve and annual energy production using methods and assumptions described in the IEC 61400-12 series of standards.
- Standard17 pagesEnglish languagesale 10% offe-Library read for×1 day
IEC 61400-12-6:2022 specifies a procedure for measuring the nacelle transfer function of a single electricity-producing, horizontal axis wind turbine, which is not considered to be a small wind turbine in accordance with IEC 61400-2. It is expected that this document be used when a valid nacelle transfer function is needed to execute a power performance measurement according to IEC 61400-12-2. This document specifies how to characterise a wind turbine's nacelle transfer function. The nacelle transfer function is determined by collecting simultaneous measurements of nacelle‑measured wind speed and free stream wind speed (as measured on a meteorological mast) for a period that is long enough to establish a statistically significant database over a range of wind speeds and under varying wind and atmospheric conditions. The procedure also provides guidance on determination of measurement uncertainty including assessment of uncertainty sources and recommendations for combining them. This first edition of IEC 61400-12-6 is part of a structural revision that cancels and replaces the performance standards IEC 61400-12-1:2017 and IEC 61400-12-2:2013. The structural revision contains no technical changes with respect to IEC 61400-12-1:2017 and IEC 61400‑12‑2:2013, but the parts that relate to wind measurements, measurement of site calibration and assessment of obstacle and terrain have been extracted into separate standards.
- Standard58 pagesEnglish languagesale 10% offe-Library read for×1 day
IEC 61400-12-3:2022 specifies a measurement and analysis procedure for deriving the wind speed correction due to terrain effects and applies to the performance testing of wind turbines of all types and sizes connected to the electrical power network as described in IEC 61400‑12‑1. The procedure applies to the performance evaluation of specific wind turbines at specific locations. The purpose of this part of IEC 61400 is to provide a uniform methodology that will ensure consistency, accuracy and reproducibility in the measurement and analysis of a site calibration for use in the determination of the power performance of wind turbines. This document provides guidance in the measurement, analysis, and reporting of the site calibration for subsequent use in power performance testing for wind turbines. This first edition of IEC 61400-12-3 is part of a structural revision that cancels and replaces the performance standards IEC 61400-12-1:2017 and IEC 61400-12-2:2013. The structural revision contains no technical changes with respect to IEC 61400-12-1:2017 and IEC 61400‑12‑2:2013, but the parts that relate to wind measurements, measurement of site calibration and assessment of obstacle and terrain have been extracted into separate standards.
- Standard47 pagesEnglish languagesale 10% offe-Library read for×1 day
Part 50 of IEC 61400 specifies methods and requirements for the application of instruments to measure wind speed (and related parameters, e.g. wind direction and turbulence intensity). Such measurements are required as an input to some of the evaluation and testing procedures for wind energy and wind turbine technology (e.g. resource evaluation and turbine testing) described by other standards in the IEC 61400 series. Part 50-2 is applicable specifically to the use of ground mounted remote sensing wind measurement instruments, i.e devices which measure the wind at some location generally above and distant from the location at which the instrument is mounted (e.g. sodars, vertical profiling lidars). This document specifically excludes other types of RSD such as forward facing or scanning lidars.
- Standard43 pagesEnglish languagesale 10% offe-Library read for×1 day
IEC 61400-50:2022 provides a general introduction to the options that are available for wind measurement, which are further detailed in the other parts of the IEC 61400-50 series. Tandis que ces autres normes définissent les cas d’utilisation relatifs aux mesurages du vent, la série IEC 61400-50 établit des exigences de mesure du vent qui sont indépendantes des cas d’utilisation. Son objectif est d’assurer que les mesurages du vent et l’évaluation des incertitudes (relative à ces mesurages) sont effectués de manière cohérente dans tout le secteur éolien; et d’assurer que ces mesurages du vent sont effectués de telle sorte que les incertitudes pouvant être quantifiées soient dans une plage acceptable. This first edition of IEC 61400-50 is part of a structural revision that cancels and replaces the performance standards IEC 61400-12-1:2017 and IEC 61400-12-2:2013. The structural revision contains no technical changes with respect to IEC 61400-12-1:2017 and IEC 61400-12-2:2013, but the parts that relate to wind measurements, measurement of site calibration and assessment of obstacle and terrain have been extracted into separate standards.
- Standard14 pagesEnglish languagesale 10% offe-Library read for×1 day
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.