EN IEC 61076-3-123:2019

Connectors for electrical and electronic equipment - Product requirements - Part 3-123: Rectangular connectors - Detail specification for hybrid connectors for industrial environments, for power supply and fibre optic data transmission, with push-pull locking

IEC 61076-3-123:2019. covers hybrid rectangular connectors with a 3 poles 16 A electric portion for power supply and a duplex fibre optic connector type LC portion for data transmission. These connectors consist of fixed and free connectors, either rewirable or non-rewirable (for both portions) and use the rectangular push-pull housing described in IEC 61076-3-117 with IP65/IP67 degree of protection, for harsh applications. The mating dimensions of such housings allow fulfilling the performance class Category I according to IEC 61753-1-3 in regards to the fibre optic portion of the connector with the exception of the operating temperature range which is –25 °C/+70 °C. The electric portion may have different rated insulation voltages. Male connectors have 3 electric round contacts Ø1,6 mm, with 16 A rated current. The fibre optic portion provides data transmission by using the common mating configurations for all variants of the type LC duplex fibre optic connectors as defined in IEC 61754-20, for dedicated fibre types and fibre termination technology covered therein. The different codings provided by this document prevent the mating of accordingly coded male or female connectors to any other similarly sized interfaces covered by other standards and the cross-mating between the different codings provided by this document. Key words: Rectangular Connectors, Hybrid Connectors, Power Supply and Fiber Optic Data Transmission.

Steckverbinder für elektronische Einrichtungen - Produktanforderungen - Teil 3-123: Rechteckige Steckverbinder - Bauartspezifikation für hybride Steckverbinder für industrielle Umgebungen, zur Stromversorgung und LWL-Datenübertragung, mit Push-Pull-Verriegelung

Connecteurs pour équipements électriques et électroniques - Exigences de produit - Partie 3-123: Connecteurs rectangulaires - Spécification particulière relative aux connecteurs hybrides dans des environnements industriels pour l’alimentation et la transmission de données fibronique, avec verrouillage de type pousser-tirer

IEC 61076-3-123:2019 couvre les connecteurs rectangulaires hybrides composés d’une partie électrique 3 pôles, 16 A pour l’alimentation et d’une partie connecteur fibronique duplex de type LC pour la transmission de données. Ces connecteurs sont constitués de fiches et d’embases, démontables ou non démontables (pour les deux parties), et utilisent le boîtier rectangulaire de type «pousser-tirer» décrit dans l’IEC 61076-3-117, offrant le degré de protection IP65/IP67, pour les applications en environnements difficiles. Les dimensions d’accouplement de tels boîtiers permettent de satisfaire à la classe de performances de catégorie I selon l’IEC 61753-1-3 en ce qui concerne la partie fibronique du connecteur, à l’exception de la plage de températures de fonctionnement, qui s’étend de -25 °C à +70 °C. La partie électrique peut avoir des tensions d’isolement assignées différentes. Les connecteurs mâles possèdent trois contacts électriques cylindriques de 1,6 mm de diamètre, avec un courant assigné de 16 A. La partie fibronique réalise la transmission de données en utilisant les configurations d’accouplement communes pour toutes les variantes de connecteurs fibroniques duplex de type LC, comme cela est défini dans l’IEC 61754-20, pour les types de fibres dédiés et la technologie de terminaison de fibre couverts ici. Les différents détrompages prévus par le présent document empêchent l’accouplement de connecteurs mâles et femelles dotés de tels détrompeurs avec une quelconque autre interface de taille semblable couverte par d’autres normes, ainsi que l’accouplement croisé entre les différents détrompages prévus par le présent document. Mots clés: Connecteurs rectangulaires, connecteurs hybrides, alimentation et la transmission de données fibronique

Konektorji za elektronsko opremo - Zahteve za proizvod - 3-123. del: Pravokotni konektorji - Podrobna specifikacija za hibridne konektorje z zaskočnim zaklepanjem, namenjene za industrijska okolja, napajanje z elektriko in prenos podatkov po optičnih kablih (IEC 61076-3-123:2019)

V standardu EN-IEC 61076-3-123 so zajeti hibridni pravokotni konektorji s 3 poli in 16-amperskim električnim delom za napajanje ter dvojni konektor optičnega kabla tipa LC z delom za prenos podatkov. Konektorji so sestavljeni iz fiksnih in prostih konektorjev, ki jih je mogoče znova povezati ali ne (za oba dela), in uporabljajo pravokotno zaskočno ohišje, opisano v standardu IEC 61076-3-117 s stopnjo zaščite IP65/IP67 za zahtevno uporabo. Dimenzije stikanja takega ohišja omogočajo izpolnjevanje razreda učinkovitosti kategorije I v skladu s standardom IEC 61753-1-3 v zvezi z delom optičnega kabla konektorja z izjemo razpona delovne temperature od –25 °C/70 °C. Nazivne izolacijske napetosti so morda drugačne za električni del. Moški konektorji imajo 3 električne okrogle kontakte s premerom 1,6 mm z nazivnim tokom 16 A.

General Information

• Status: Published
• Publication Date: 07-Nov-2019
• Withdrawal Date: 17-Oct-2022
• ICS: 31.220.10 - Plug-and-socket devices. Connectors
• Technical Committee: CLC/SR 48B - Connectors
• Drafting Committee: IEC/SC 48B - IEC_SC_48B
• Current Stage: 6060 - Document made available - Publishing
• Start Date: 08-Nov-2019
• Completion Date: 08-Nov-2019
• Ref Project: SIST EN IEC 61076-3-123:2020 - Connectors for electronic equipment - Product requirements - Part 3-123: Rectangular connectors - Detail specification for hybrid connectors for industrial environments, for power supply and fibre optic data transmission, with push-pull locking (IEC 61076-3-123:2019)

Standards Content (Sample)

SLOVENSKI STANDARD
01-januar-2020
Konektorji za elektronsko opremo - Zahteve za proizvod - 3-123. del: Pravokotni
konektorji - Podrobna specifikacija za hibridne konektorje z zaskočnim
zaklepanjem, namenjene za industrijska okolja, napajanje z elektriko in prenos
podatkov po optičnih kablih (IEC 61076-3-123:2019)
Connectors for electronic equipment - Product requirements - Part 3-123: Rectangular
connectors - Detail specification for hybrid connectors for industrial environments, for
power supply and fibre optic data transmission, with push-pull locking (IEC 61076-3-
123:2019)
Steckverbinder für elektronische Einrichtungen - Produktanforderungen - Teil 3-123:
Rechteckige Steckverbinder - Bauartspezifikation für hybride Steckverbinder für
industrielle Umgebungen, zur Stromversorgung und LWL-Datenübertragung, mit Push-
Pull-Verriegelung (IEC 61076-3-123:2019)
Connecteurs pour équipements électriques et électroniques - Exigences de produit -
Partie 3-123: Connecteurs rectangulaires - Spécification particulière relative aux
connecteurs hybrides dans des environnements industriels pour l’alimentation et la
transmission de données fibronique, avec verrouillage de type pousser-tirer (IEC 61076-
3-123:2019)
Ta slovenski standard je istoveten z: EN IEC 61076-3-123:2019
ICS:
31.220.10 Vtiči in vtičnice, konektorji Plug-and-socket devices.
Connectors
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD EN IEC 61076-3-123

NORME EUROPÉENNE
EUROPÄISCHE NORM
November 2019
ICS 31.220.10
English Version
Connectors for electrical and electronic equipment - Product
requirements - Part 3-123: Rectangular connectors - Detail
specification for hybrid connectors for industrial environments,
for power supply and fibre optic data transmission, with push-pull
locking
(IEC 61076-3-123:2019)
Connecteurs pour équipements électriques et électroniques Steckverbinder für elektronische Einrichtungen -
- Exigences de produit - Partie 3-123: Connecteurs Produktanforderungen - Teil 3-123: Rechteckige
rectangulaires - Spécification particulière relative aux Steckverbinder - Bauartspezifikation für hybride
connecteurs hybrides dans des environnements industriels Steckverbinder für industrielle Umgebungen, zur
pour l'alimentation et la transmission de données Stromversorgung und LWL-Datenübertragung, mit Push-
fibronique, avec verrouillage de type pousser-tirer Pull-Verriegelung
(IEC 61076-3-123:2019) (IEC 61076-3-123:2019)
This European Standard was approved by CENELEC on 2019-10-18. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.

European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2019 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN IEC 61076-3-123:2019 E

European foreword
The text of document 48B/2742/FDIS, future edition 1 of IEC 61076-3-123, prepared by SC 48B
"Electrical connectors" of IEC/TC 48 "Electrical connectors and mechanical structures for electrical
and electronic equipment" was submitted to the IEC-CENELEC parallel vote and approved by
CENELEC as EN IEC 61076-3-123:2019.
The following dates are fixed:
• latest date by which the document has to be implemented at national (dop) 2020-07-18
level by publication of an identical national standard or by endorsement
• latest date by which the national standards conflicting with the (dow) 2022-10-18
document have to be withdrawn
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.

Endorsement notice
The text of the International Standard IEC 61076-3-123:2019 was approved by CENELEC as a
European Standard without any modification.

Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments)
applies.
NOTE 1  Where an International Publication has been modified by common modifications, indicated by (mod), the relevant
EN/HD applies.
NOTE 2  Up-to-date information on the latest versions of the European Standards listed in this annex is available here:
www.cenelec.eu.
Publication Year Title EN/HD Year
IEC 60050-581 2008 International Electrotechnical Vocabulary - Part 581: - -
Electromechanical components for electronic
equipment
IEC 60068-1 -  Environmental testing - Part 1: General and guidance EN 60068-1 -
IEC 60068-2-30 -  Environmental testing - Part 2-30: Tests - Test Db: EN 60068-2-30 -
Damp heat, cyclic (12 h + 12 h cycle)
IEC 60352-1 1997 Solderless connections - Part 1: Wrapped connections EN 60352-1 1997
- General requirements, test methods and practical
guidance
IEC 60352-2 2006 Solderless connections - Part 2: Crimped connections EN 60352-2 2006
- General requirements, test methods and practical
guidance
IEC 60352-3 1993 Solderless connections - Part 3: Solderless accessible EN 60352-3 1994
insulation displacement connections - General
requirements, test methods and practical guidance
IEC 60352-4 1994 Solderless connections - Part 4: Solderless non- EN 60352-4 1994
accessible insulation displacement connections -
General requirements, test methods and practical
guidance
IEC 60352-5 2012 Solderless connections - Part 5: Press-in connections EN 60352-5 2012
- General requirements, test methods and practical
guidance
IEC 60352-6 1997 Solderless connections - Part 6: Insulation piercing EN 60352-6 1997
connections - General requirements, test methods
and practical guidance
IEC 60352-7 2002 Solderless connections - Part 7: Spring clamp EN 60352-7 2002
connections - General requirements, test methods
and practical guidance
IEC 60352-8 2011 Solderless connections - Part 8: Compression mount EN 60352-8 2011
connections - General requirements, test methods
and practical guidance
IEC 60512-1-1 -  Connectors for electronic equipment - Tests and EN 60512-1-1 -
measurements - Part 1-1: General examination - Test
1a: Visual examination
IEC 60512-1-2 2002 Connectors for electronic equipment - Tests and EN 60512-1-2 2002
measurements - Part 1-2: General examination - Test
1b: Examination of dimension and mass
IEC 60512-2-1 2002 Connectors for electronic equipment - Tests and EN 60512-2-1 2002
measurements - Part 2-1: Electrical continuity and
contact resistance tests - Test 2a: Contact resistance
- Millivolt level method
IEC 60512-2-2 -  Connectors for electronic equipment - Tests and EN 60512-2-2 -
measurements - Part 2-2: Electrical continuity and
contact resistance tests - Test 2b: Contact resistance
- Specified test current method
IEC 60512-2-5 -  Connectors for electronic equipment - Tests and EN 60512-2-5 -
measurements - Part 2-5: Electrical continuity and
contact resistance tests - Test 2e: Contact
disturbance
IEC 60512-3-1 2002 Connectors for electronic equipment - Tests and EN 60512-3-1 2002
measurements - Part 3-1: Insulation tests - Test 3a:
Insulation resistance
IEC 60512-4-1 2003 Connectors for electronic equipment - Tests and EN 60512-4-1 2003
measurements - Part 4-1: Voltage stress tests - Test
4a: Voltage proof
IEC 60512-5-2 2002 Connectors for electronic equipment - Tests and EN 60512-5-2 2002
measurements - Part 5-2: Current-carrying capacity
tests - Test 5b: Current-temperature derating
IEC 60512-6-3 2002 Connectors for electronic equipment - Tests and EN 60512-6-3 2002
measurements - Part 6-3: Dynamic stress tests - Test
6c: Shock
IEC 60512-6-4 2002 Connectors for electronic equipment - Tests and EN 60512-6-4 2002
measurements - Part 6-4: Dynamic stress tests - Test
6d: Vibration (sinusoidal)
IEC 60512-6-5 -  Electromechanical components for electronic EN 60512-6-5 -
equipment - Basic testing procedures and measuring
methods - Part 6: Dynamic stress tests - Section 5:
Test 6e: Random vibration
IEC 60512-8-1 2010 Connectors for electronic equipment - Tests and EN 60512-8-1 2010
measurements - Part 8-1: Static load tests (fixed
connectors) - Test 8a: Static load, transverse
IEC 60512-8-2 2011 Connectors for electronic equipment - Tests and EN 60512-8-2 2011
measurements - Part 8-2: Static load tests (fixed
connectors) - Test 8b: Static load, axial
IEC 60512-9-1 2010 Connectors for electronic equipment - Tests and EN 60512-9-1 2010
measurements - Part 9-1: Endurance tests - Test 9a:
Mechanical operation
IEC 60512-9-2 -  Connectors for electronic equipment - Tests and EN 60512-9-2 -
measurements - Part 9-2: Endurance tests - Test 9b:
Electrical load and temperature
IEC 60512-11-1 -  Connectors for electrical and electronic equipment - EN IEC 60512--
Tests and measurements - Part 11-1: Climatic tests - 11-1
Test 11a - Climatic sequence
IEC 60512-11-3 -  Connectors for electronic equipment - Tests and EN 60512-11-3 -
measurements - Part 11-3: Climatic tests - Test 11c:
Damp heat, steady state
IEC 60512-11-4 -  Connectors for electronic equipment - Tests and EN 60512-11-4 -
measurements - Part 11-4: Climatic tests - Test 11d:
Rapid change of temperature
IEC 60512-11-9 -  Connectors for electronic equipment - Tests and EN 60512-11-9 -
measurements - Part 11-9: Climatic tests - Test 11i:
Dry heat
IEC 60512-11-10 -  Connectors for electronic equipment - Tests and EN 60512-11-10 -
measurements - Part 11-10: Climatic tests - Test 11j:
Cold
IEC 60512-11-12 -  Connectors for electronic equipment - Tests and EN 60512-11-12 -
measurements - Part 11-12: Climatic tests - Test 11m:
Damp heat, cyclic
IEC 60512-12-4 -  Connectors for electronic equipment - Tests and EN 60512-12-4 -
measurements - Part 12-4: Soldering tests - Test 12d:
Resistance to soldering heat, solder bath method
IEC 60512-12-5 -  Connectors for electronic equipment - Tests and EN 60512-12-5 -
measurements - Part 12-5: Soldering tests - Test 12e:
Resistance to soldering heat, soldering iron method
IEC 60512-13-1 2006 Connectors for electronic equipment - Tests and EN 60512-13-1 2006
measurements - Part 13-1: Mechanical operation tests
- Test 13a: Engaging and separating forces
- -   + corrigendum 2006
Dec.
IEC 60512-13-2 -  Connectors for electronic equipment - Tests and EN 60512-13-2 -
measurements - Part 13-2: Mechanical operation tests
- Test 13b: Insertion and withdrawal forces
IEC 60512-13-5 2006 Connectors for electronic equipment - Tests and EN 60512-13-5 2006
measurements - Part 13-5: Mechanical operation tests
- Test 13e: Polarizing and keying method
- -   + corrigendum 2006
Dec.
IEC 60512-14-7 -  Electromechanical components for electronic EN 60512-14-7 -
equipment - Basic testing procedures and measuring
methods - Part 14: Sealing tests - Section 7: Test 14g:
Impacting water
IEC 60512-15-1 -  Connectors for electronic equipment - Tests and EN 60512-15-1 -
measurements - Part 15-1: Connector tests
(mechanical) - Test 15a: Contact retention in insert
IEC 60512-15-6 2008 Connectors for electronic equipment - Tests and EN 60512-15-6 2008
measurements - Part 15-6: Connector tests
(mechanical) - Test 15f: Effectiveness of connector
coupling devices
IEC 60512-16-5 -  Connectors for electronic equipment - Tests and EN 60512-16-5 -
measurements - Part 16-5: Mechanical tests on
contacts and terminations - Test 16e: Gauge retention
force (resilient contacts)
IEC 60512-17-3 -  Connectors for electronic equipment - Tests and EN 60512-17-3 -
measurements - Part 17-3: Cable clamping tests -
Test 17c: Cable clamp resistance to cable pull
(tensile)
IEC 60512-17-4 -  Connectors for electronic equipment - Tests and EN 60512-17-4 -
measurements - Part 17-4: Cable clamping tests -
Test 17d: Cable clamp resistance to cable torsion
IEC 60512-19-3 -  Electromechanical components for electronic EN 60512-19-3 -
equipment - Basic testing procedures and measuring
methods - Part 19: Chemical resistance tests -
Section 3: Test 19c - Fluid resistance
IEC 60529 1989 Degrees of protection provided by enclosures (IP EN 60529 1991
Code)
IEC 60603-7 -  Connectors for electronic equipment - Part 7: Detail EN 60603-7 -
specification for 8-way, unshielded, free and fixed
connectors
IEC 60664-1 2007 Insulation coordination for equipment within low- EN 60664-1 2007
voltage systems - Part 1: Principles, requirements and
tests
IEC 60793-2-10 -  Optical fibres - Part 2-10: Product specifications - EN IEC 60793-2--
Sectional specification for category A1 multimode 10
fibres
---------------------- Pa
...