EN IEC 60794-1-127:2026
(Main)Optical fibre cables - Part 1-127: Generic specification - Basic optical cable test procedures - Mechanical tests methods - Indoor simulated installation test, method E27
- Status
- Not Published
- Publication Date
- 12-Nov-2026
- Technical Committee
- CLC/TC 86A - Optical fibres and optical fibre cables
- Current Stage
- 5060 - Voting results sent to TC, SR - Formal Approval
- Start Date
- 24-Jul-2026
- Completion Date
- 24-Jul-2026
EN IEC 60794-1-127:2026 is a CLC standard for optical fibre cables that defines the E27 indoor simulated installation test. It applies to cables used with telecommunication equipment and similar devices, including cables that combine optical fibres and electrical conductors. The standard tells manufacturers and test laboratories how to simulate indoor routing around corners and attachment points, and how to judge the cable’s optical and mechanical response after the test.
What does EN IEC 60794-1-127:2026 specify?
EN IEC 60794-1-127:2026 specifies a mechanical test method for indoor simulated installation of optical fibre cables. The purpose is to create uniform requirements for evaluating cable performance when the cable is routed in ways that can occur inside buildings, such as around tight corners and at fixing points.
EN IEC 60794-1-127:2026 is organized into Scope, Normative references, Terms and definitions, and Method E27. Method E27 is then divided into object, sample, apparatus, procedure, requirements, details to be specified, and details to be reported. Figures 1 and 2 show the simulation apparatus and the stapling and bending fixture.
What are the key requirements of EN IEC 60794-1-127:2026?
Test purpose and sample handling
- EN IEC 60794-1-127:2026 uses Method E27 to simulate indoor installation where tight corners, attachment points and cable storage can occur. In practice, that means the method is aimed at cables that may see more severe handling than routine installation.
- EN IEC 60794-1-127:2026 says the sample must be long enough for the procedure and the optical measurements, and it recommends a minimum sample length. This matters because the test must include the full routing path without forcing a shortened or unrealistic setup.
- EN IEC 60794-1-127:2026 notes that the test is primarily intended for cables with bending loss insensitive fibres. For readers, that means the method is especially relevant when the design is expected to tolerate indoor bending and fixing.
Apparatus and test sequence
- EN IEC 60794-1-127:2026 uses a substrate such as a wall stud or similar support, with fixtures that represent routing around a door, window or obstacle. The exact material and attachment approach are tied to local building practice, so the relevant specification has to match the intended installation environment.
- EN IEC 60794-1-127:2026 runs the cable through a set of corner-bend, loaded-bend, mandrel-wrap and attachment-point conditions. In practice, the cable is exposed to a realistic sequence of indoor installation stresses rather than a single bend only.
- EN IEC 60794-1-127:2026 allows optical monitoring during the test, and when that is used the fibres should stay connected throughout the procedure. This lets the tester watch attenuation changes while the cable is being stressed.
Evaluation and reporting
- EN IEC 60794-1-127:2026 requires attenuation to be measured before the test when optical performance requirements apply, and measured again after the test. The important result is the change in attenuation relative to the initial value.
- EN IEC 60794-1-127:2026 leaves acceptance criteria to the relevant specification, but it identifies typical failure modes such as cable damage, excessive attenuation change, or loss of continuity. That means the user must state the pass-fail rule before testing starts.
- EN IEC 60794-1-127:2026 also asks the relevant specification and the test report to state the cable type, substrate, attachment method, residual load, temperature, acceptance criteria, results, and any deviations. This makes the test repeatable and lets another lab understand exactly how the result was obtained.
What terms does EN IEC 60794-1-127:2026 define?
EN IEC 60794-1-127:2026 uses the terms and definitions from IEC 60794-1-1, and it relies on a few key test-specific terms.
- Method E27 - the indoor simulated installation test defined in this part.
- Optical cable - a broad term that may also include optical fibre units and microduct fibre units.
- Initial attenuation - the attenuation measured before the test and used as the baseline.
- Change in attenuation - the difference between the post-test and pre-test attenuation values.
- Rated residual load - the residual load specified for the cable and used in the loaded bend step.
- F.D. - the cable fixing device shown in the apparatus figure, used to wind and weight the cable.
- F2 - the load used in the loaded corner-bend condition.
Who uses EN IEC 60794-1-127:2026?
EN IEC 60794-1-127:2026 is used by cable manufacturers, test laboratories, product engineers, and quality teams working with indoor optical fibre cables. It helps them qualify a design, compare cable constructions, set product test conditions, and document attenuation or physical damage after simulated installation. It is also useful to buyers and specifiers who need a named method for indoor cable performance testing.
What changed in EN IEC 60794-1-127:2026 from the previous edition?
EN IEC 60794-1-127:2026 replaces Method E27 of the first edition of IEC 60794-1-21:2015. The document describes this as a technical revision and says the significant technical change is the addition of a new clause for reporting details. It also follows the new structure in which each test method is issued as an individual document in the IEC 60794-1-1xx series.
Which standards are used with EN IEC 60794-1-127:2026?
- IEC 60794-1-1 - provides the general specification and the shared terms and definitions used in this part.
- IEC 60794-1-2 - provides general guidance, general requirements, and the broader reference guide to optical fibre cable test methods.
- IEC 60793-1-46 - provides the monitoring method for changes in attenuation when optical performance is tracked during the test.
What does the EN IEC 60794-1-127:2026 document contain?
EN IEC 60794-1-127:2026 contains the full E27 test method, including the stated object, sample requirements, apparatus description, procedure, and acceptance framework. It also includes what the relevant specification must define and what the test report must record. Figures 1 and 2 give the indoor installation simulation apparatus and the stapling and bending fixture used in the method.
Relations
- Effective Date
- 09-Sep-2025
- Effective Date
- 09-Sep-2025
- Effective Date
- 27-Oct-2026
- Effective Date
- 27-Oct-2026
- Effective Date
- 27-Oct-2026
Get Certified
Connect with accredited certification bodies for this standard
ANCE
Mexican certification and testing association.
Intertek Slovenia
Intertek testing, inspection, and certification services in Slovenia.
LNE (Laboratoire National de Métrologie et d'Essais)
French national laboratory for metrology and testing.
Sponsored listings
Frequently Asked Questions
EN IEC 60794-1-127:2026 is a draft published by CLC. Its full title is "Optical fibre cables - Part 1-127: Generic specification - Basic optical cable test procedures - Mechanical tests methods - Indoor simulated installation test, method E27". This standard covers: Optical fibre cables - Part 1-127: Generic specification - Basic optical cable test procedures - Mechanical tests methods - Indoor simulated installation test, method E27
Optical fibre cables - Part 1-127: Generic specification - Basic optical cable test procedures - Mechanical tests methods - Indoor simulated installation test, method E27
EN IEC 60794-1-127:2026 is classified under the following ICS (International Classification for Standards) categories: 33.180.10 - Fibres and cables. The ICS classification helps identify the subject area and facilitates finding related standards.
EN IEC 60794-1-127:2026 has the following relationships with other standards: It is inter standard links to EN 60794-1-21:2015, EN 60794-1-21:2015/A1:2020, EN IEC 60794-1-1:2023, EN IEC 60794-1-2:2021, EN IEC 60793-1-46:2024. Understanding these relationships helps ensure you are using the most current and applicable version of the standard.
EN IEC 60794-1-127:2026 is available in PDF format for immediate download after purchase. The document can be added to your cart and obtained through the secure checkout process. Digital delivery ensures instant access to the complete standard document.
Standards Content (Sample)
SLOVENSKI STANDARD
oSIST prEN IEC 60794-1-127:2025
01-april-2025
Optični kabli - 1-127. del: Splošna specifikacija - Osnovni preskusni postopki za
optične kable - Mehanske preskusne metode - Preskus simulirane namestitve v
notranjih prostorih, metoda e27
Optical fibre cables - Part 1-127: Generic specification - Basic optical cable test
procedures - Mechanical tests methods - Indoor simulated installation test, method e27
Câbles à fibres optiques - Partie1-127: Spécification générique - Procédures
fondamentales d’essais des câbles optiques - Méthodes d’essais mécaniques - Essai
d'installation simulée en intérieur, méthode e27
Ta slovenski standard je istoveten z: prEN IEC 60794-1-127:2025
ICS:
33.180.10 (Optična) vlakna in kabli Fibres and cables
oSIST prEN IEC 60794-1-127:2025 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
oSIST prEN IEC 60794-1-127:2025
oSIST prEN IEC 60794-1-127:2025
86A/2538/CDV
COMMITTEE DRAFT FOR VOTE (CDV)
PROJECT NUMBER:
IEC 60794-1-127 ED1
DATE OF CIRCULATION: CLOSING DATE FOR VOTING:
2025-02-21 2025-05-16
SUPERSEDES DOCUMENTS:
86A/2459/CD, 86A/2535/CC
IEC SC 86A : FIBRES AND CABLES
SECRETARIAT: SECRETARY:
France Mr Laurent Gasca
OF INTEREST TO THE FOLLOWING COMMITTEES: HORIZONTAL FUNCTION(S):
ASPECTS CONCERNED:
SUBMITTED FOR CENELEC PARALLEL VOTING NOT SUBMITTED FOR CENELEC PARALLEL VOTING
Attention IEC-CENELEC parallel voting
The attention of IEC National Committees, members of
CENELEC, is drawn to the fact that this Committee Draft
for Vote (CDV) is submitted for parallel voting.
The CENELEC members are invited to vote through the
CENELEC online voting system.
This document is still under study and subject to change. It should not be used for reference purposes.
Recipients of this document are invited to submit, with their comments, notification of any relevant patent rights of
which they are aware and to provide supporting documentation.
Recipients of this document are invited to submit, with their comments, notification of any relevant “In Some
Countries” clauses to be included should this proposal proceed. Recipients are reminded that the CDV stage is
the final stage for submitting ISC clauses. (SEE AC/22/2007 OR NEW GUIDANCE DOC).
TITLE:
Optical fibre cables - Part 1-127: Generic specification - Basic optical cable test procedures -
Mechanical tests methods - Indoor simulated installation test, Method E27
PROPOSED STABILITY DATE: 2028
NOTE FROM TC/SC OFFICERS:
electronic file, to make a copy and to print out the content for the sole purpose of preparing National Committee positions.
You may not copy or "mirror" the file or printed version of the document, or any part of it, for any other purpose without
permission in writing from IEC.
oSIST prEN IEC 60794-1-127:2025
IEC CDV 60794-1-127 ED1 © IEC 2025 2 86A/2538/CDV
1 CONTENTS
2 CONTENTS . 2
3 FOREWORD . 3
4 INTRODUCTION . 5
5 1 Scope . 6
6 2 Normative references . 6
7 3 Terms and definitions . 6
8 4 Method E27: Indoor simulated installation test . 6
9 4.1 Object . 6
10 4.2 Sample . 7
11 4.3 Apparatus . 7
12 4.4 Procedure . 8
13 4.5 Requirements . 9
14 4.6 Details to be specified . 9
15 4.7 Details to be reported . 9
17 Figure 1 – Indoor installation simulation apparatus. 7
18 Figure 2 – Stapling and bending test fixture . 7
oSIST prEN IEC 60794-1-127:2025
IEC CDV 60794-1-127 ED1 © IEC 2025 3 86A/2538/CDV
21 INTERNATIONAL ELECTROTECHNICAL COMMISSION
22 ____________
24 OPTICAL FIBRE CABLES –
26 Part 1-127: Generic specification –
27 Basic optical cable test procedures –
28 Mechanical tests methods - Indoor simulated installation test, method E27
30 FOREWORD
31 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
32 all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international
33 co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and
34 in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports,
35 Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their
36 preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with
37 may participate in this preparatory work. International, governmental and non-governmental organizations liaising
38 with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for
39 Standardization (ISO) in accordance with conditions determined by agreement between the two organizations.
40 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
41 consensus of opinion on the relevant subjects since each technical committee has representation from all
42 interested IEC National Committees.
43 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
44 Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
45 Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
46 misinterpretation by any end user.
47 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
48 transparently to the maximum extent possible in their national and regional publications. Any divergence between
49 any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter.
50 5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
51 assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
52 services carried out by independent certification bodies.
53 6) All users should ensure that they have the latest edition of this publication.
54 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
55 members of its technical committees and IEC National Committees for any personal injury, property damage or
56 other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
57 expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications.
58 8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
59 indispensable for the correct application of this publication.
60 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent
61 rights. IEC shall not be held responsible for identifying any or all such patent rights.
62 International Standard IEC 60794-1-21 has been prepared by subcommittee 86A: Fibres and cables, of IEC
63 technical committee 86: Fibre optics.
64 IEC 60794-1-127 has been prepared by subcommittee 86A: Fibres and cables, of IEC
65 technical committee 86: Fibre optics. It is an International Standard.
67 This first edition cancels and replaces Method E27 of the first edition of IEC 60794-1-21:2015,
68 which will be withdrawn. It constitutes a technical revision.
69 This edition includes the following significant technical changes with respect to the previous
70 edition:
71 a) added a new clause “4.7 Details to be reported”;
72 The text of this is based on the following documents:
Draft Report on voting
XX/XX/FDIS XX/XX/RVD
oSIST prEN IEC 60794-1-127:2025
IEC CDV 60794-1-127 ED1 © IEC 2025 4 86A/2538/CDV
74 Full information on the voting for its approval can be found in the report on voting indicated in
75 the above table.
76 The language used for the development of this International Standard is English.
77 This document was drafted in accordance with ISO/IEC Directives, Part 2, and developed in
78 accordance with ISO/IEC Directives, Part 1 and ISO/IEC Directives, IEC Supplement, available
79 at www.iec.ch/members_experts/refdocs. The main document types developed by IEC are
80 described in greate
...