EN IEC 60793-1-46:2024
(Main)Optical fibres - Part 1-46: Measurement methods and test procedures - Monitoring of changes in attenuation
Optical fibres - Part 1-46: Measurement methods and test procedures - Monitoring of changes in attenuation
IEC 60793-1-46:2024 establishes uniform requirements for the monitoring of changes in attenuation, thereby assisting in the inspection of fibres and cables for commercial purposes. This document gives two methods for monitoring the changes in attenuation of optical fibres and cables that occur during mechanical or environmental testing, or both. It provides a monitor in the change of attenuation characteristics arising from optical discontinuity, physical defects and modifications of the attenuation slope: - method A: change in attenuation by transmitted power; - method B: change in attenuation by backscattering. Methods A and B apply to the monitoring of all categories of the following fibres: - class A: multimode fibres; - class B: single-mode fibres; - class C: single-mode intraconnection fibres. Information common to both measurements is contained in Clause 1 to Clause 10, and information pertaining to each individual method appears in Annex A, and Annex B respectively.
Lichtwellenleiter - Teil 1-46: Messmethoden und Prüfverfahren - Überwachung von Änderungen der optischen Dämpfung
Fibres optiques - Partie 1-46: Méthodes de mesure et procédures d’essai - Contrôle des variations de l’affaiblissement
L’IEC 60793-1-46:2024 établit des exigences uniformes pour le contrôle des variations de l’affaiblissement, contribuant ainsi au contrôle des fibres et câbles dans le cadre des relations commerciales. Le présent document décrit deux méthodes pour contrôler les variations de l’affaiblissement des fibres optiques et des câbles qui se produisent au cours des essais mécaniques et d’environnement, ou des deux. Il fournit un moyen de contrôle de la variation des caractéristiques d’affaiblissement qui proviennent de la discontinuité optique, de défauts physiques et de modifications de la pente d’affaiblissement: - Méthode A: variation de l’affaiblissement en puissance transmise; - Méthode B : variation de l’affaiblissement en rétrodiffusion. Les méthodes A et B s’appliquent au contrôle de toutes les catégories de fibres suivantes: - Classe A: fibres multimodales; - Classe B: fibres unimodales; - Classe C: fibres d’intraconnexion unimodales. Les informations communes aux deux mesures sont contenues dans les Articles 1 à 10 et les informations relatives à chacune des méthodes se trouvent respectivement dans les Annexe A et Annexe B.
Optična vlakna - 1-46. del: Merilne metode in postopki preskušanja - Nadzorovanje sprememb slabljenja (IEC 60793-1-46:2024)
Standard IEC 60793-1-46:2024 določa enotne zahteve za nadzorovanje sprememb slabljenja, s čimer je v pomoč pri pregledovanju vlaken in kablov za komercialne namene. Ta dokument podaja dve metodi za nadzorovanje sprememb slabljenja optičnih vlaken in kablov, do katerih pride med mehanskim ali okoljskim preskušanjem ali obojim. Omogoča nadzorovanje sprememb značilnosti slabljenja zaradi optične nepravilnosti, fizičnih okvar in sprememb nagiba slabljenja:
– metoda A: sprememba slabljenja zaradi prenosa moči;
– metoda B: sprememba slabljenja zaradi povratnega sipanja.
Metodi A in B se uporabljata za nadzorovanje vseh kategorij naslednjih vlaken:
– razred A: večrodovna vlakna;
– razred B: enorodovna vlakna;
– razred C: enorodovna spojena vlakna.
Informacije, skupne obema meritvama, so navedene v točkah 1 do 10, pri čemer so informacije v zvezi s posamezno metodo navedene v dodatku A oziroma B.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-oktober-2024
Optična vlakna - 1-46. del: Merilne metode in postopki preskušanja - Nadzorovanje
sprememb slabljenja (IEC 60793-1-46:2024)
Optical fibres - Part 1-46: Measurement methods and test procedures - Monitoring of
changes in attenuation (IEC 60793-1-46:2024)
Lichtwellenleiter – Teil 1-46: Messmethoden und Prüfverfahren - Überwachung von
Änderungen der optischen Dämpfung (IEC 60793-1-46:2024)
Fibres optiques - Partie 1-46: Méthodes de mesure et procédures d'essai - Contrôle des
variations du facteur de transmission optique (IEC 60793-1-46:2024)
Ta slovenski standard je istoveten z: EN IEC 60793-1-46:2024
ICS:
33.180.10 (Optična) vlakna in kabli Fibres and cables
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD EN IEC 60793-1-46
NORME EUROPÉENNE
EUROPÄISCHE NORM August 2024
ICS 33.180.10 Supersedes EN 60793-1-46:2002
English Version
Optical fibres - Part 1-46: Measurement methods and test
procedures - Monitoring of changes in attenuation
(IEC 60793-1-46:2024)
Fibres optiques - Partie 1-46: Méthodes de mesure et Lichtwellenleiter - Teil 1-46: Messmethoden und
procédures d'essai - Contrôle des variations de Prüfverfahren - Überwachung von Änderungen der
l'affaiblissement optischen Dämpfung
(IEC 60793-1-46:2024) (IEC 60793-1-46:2024)
This European Standard was approved by CENELEC on 2024-08-01. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Türkiye and the United Kingdom.
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2024 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN IEC 60793-1-46:2024 E
European foreword
The text of document 86A/2442/FDIS, future edition 2 of IEC 60793-1-46, prepared by SC 86A "Fibres
and cables" of IEC/TC 86 "Fibre optics" was submitted to the IEC-CENELEC parallel vote and
approved by CENELEC as EN IEC 60793-1-46:2024.
The following dates are fixed:
• latest date by which the document has to be implemented at national (dop) 2025-05-01
level by publication of an identical national standard or by endorsement
• latest date by which the national standards conflicting with the (dow) 2027-08-01
document have to be withdrawn
This document supersedes EN 60793-1-46:2002 and all of its amendments and corrigenda (if any).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
Any feedback and questions on this document should be directed to the users’ national committee. A
complete listing of these bodies can be found on the CENELEC website.
Endorsement notice
The text of the International Standard IEC 60793-1-46:2024 was approved by CENELEC as a
European Standard without any modification.
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments)
applies.
NOTE 1 Where an International Publication has been modified by common modifications, indicated by (mod),
the relevant EN/HD applies.
NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is available
here: www.cencenelec.eu.
Publication Year Title EN/HD Year
IEC 60793-1-40 - Optical fibres - Part 1-40: Attenuation EN IEC 60793-1-40 -
measurement methods
IEC 60793-1-46 ®
Edition 2.0 2024-06
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Optical fibres –
Part 1-46: Measurement methods and test procedures – Monitoring of changes in
attenuation
Fibres optiques –
Partie 1-46: Méthodes de mesure et procédures d’essai – Contrôle des variations
de l’affaiblissement
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 33.180.10 ISBN 978-2-8322-9194-8
– 2 – IEC 60793-1-46:2024 © IEC 2024
CONTENTS
FOREWORD . 3
INTRODUCTION . 5
1 Scope . 6
2 Normative references . 6
3 Terms and definitions . 6
4 Reference test method . 6
5 Apparatus . 7
6 Sampling . 7
6.1 Sample length . 7
6.2 Sample end face . 7
6.3 Sample preparation . 7
6.4 Reference sample . 7
7 Procedure . 7
8 Calculations . 7
9 Results . 7
9.1 Information to be provided with each measurement . 7
9.2 Information available upon request . 8
10 Specification information . 8
Annex A (normative) Requirements specific to method A – Change in attenuation by
transmitted power . 9
A.1 Apparatus . 9
A.1.1 General . 9
A.1.2 Optical source . 9
A.1.3 Optical divider . 9
A.1.4 Optical detector . 9
A.1.5 Launch apparatus . 10
A.2 Procedure . 10
A.3 Calculations . 11
Annex B (normative) Requirements specific to method B – Change in attenuation by
backscattering . 12
B.1 Apparatus . 12
B.2 Procedure . 12
B.3 Calculations . 12
Figure A.1 – Measurement of change in attenuation using reference sample . 10
Figure A.2 – Measurement of change in attenuation using stabilized source . 10
IEC 60793-1-46:2024 © IEC 2024 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
OPTICAL FIBRES –
Part 1-46: Measurement methods and test procedures –
Monitoring of changes in attenuation
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international
co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and
in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports,
Publicly Available Specifications (PAS) and Guides (hereafter referred to as "IEC Publication(s)"). Their
preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with
may participate in this preparatory work. International, governmental and non-governmental organizations liaising
with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for
Standardization (ISO) in accordance with conditions determined by agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence between
any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) IEC draws attention to the possibility that the implementation of this document may involve the use of (a)
patent(s). IEC takes no position concerning the evidence, validity or applicability of any claimed patent rights in
respect thereof. As of the date of publication of this document, IEC had not received notice of (a) patent(s), which
may be required to implement this document. However, implementers are cautioned that this may not represent
the latest information, which may be obtained from the patent database available at https://patents.iec.ch. IEC
shall not be held responsible for identifying any or all such patent rights.
IEC 60793-1-46 has b
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.