iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CLC

CLC/TS 50131-4:2006

(Main)

Alarm systems - Intrusion and hold-up systems - Part 4: Warning devices

Alarm systems - Intrusion and hold-up systems - Part 4: Warning devices

This Technical Specification includes requirements for warning devices used in Intrusion and Hold up Alarm Systems installed in buildings. Four grades of warning device are described corresponding to each of the four security grades given in the European standard EN 50131-1. Requirements are also given for four environmental classes covering applications in internal and outdoor locations as specified in EN 50130-5.

Alarmanlagen - Einbruchmeldeanlagen - Teil 4: Signalgeber

Systèmes d'alarme - Systèmes d'alarme intrusion - Partie 4: Dispositifs d'avertissement

Alarmni sistemi - Sistemi za javljanje vloma - 4. del: Opozorilne naprave

General Information

Status
Withdrawn
Publication Date
20-Nov-2006
ICS
13.310 - Protection against crime
Technical Committee
CLC/TC 79 - Alarm systems
Parallel Committee
IEC/TC 79 - IEC_TC_79
Current Stage
9960 - Withdrawal effective - Withdrawal
Start Date
01-May-2012
Completion Date
01-May-2012
Ref Project
SIST-TS CLC/TS 50131-4:2007 - Alarm systems - Intrusion and hold-up systems -- Part 4: Warning devices

Relations

Replaced By
EN 50131-4:2009 - Alarm systems - Intrusion and hold-up systems - Part 4: Warning devices
Effective Date
28-Jan-2023

Buy Standard

TS CLC/prTS 50131-4:2006TS CLC/prTS 50131-4:2006
PreviousNext
Technical specification
TS CLC/prTS 50131-4:2006
English language
35 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day
TS CLC/TS 50131-4:2007TS CLC/TS 50131-4:2007
PreviousNext
Technical specification
TS CLC/TS 50131-4:2007
English language
35 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST-TS CLC/TS 50131-4:2007
01-december-2007
Alarmni sistemi - Sistemi za javljanje vloma - 4. del: Opozorilne naprave
Alarm systems - Intrusion and hold-up systems -- Part 4: Warning devices
Alarmanlagen - Einbruchmeldeanlagen -- Teil 4: Signalgeber
Systèmes d'alarme - Systèmes d'alarme intrusion -- Partie 4: Dispositifs d'avertissement
Ta slovenski standard je istoveten z: CLC/TS 50131-4:2006
ICS:
13.310 Varstvo pred kriminalom Protection against crime
13.320 Alarmni in opozorilni sistemi Alarm and warning systems
SIST-TS CLC/TS 50131-4:2007 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST-TS CLC/TS 50131-4:2007

---------------------- Page: 2 ----------------------

SIST-TS CLC/TS 50131-4:2007


TECHNICAL SPECIFICATION
CLC/TS 50131-4

SPÉCIFICATION TECHNIQUE
November 2006
TECHNISCHE SPEZIFIKATION

ICS 13.310


English version


Alarm systems -
Intrusion and hold-up systems -
Part 4: Warning devices



Systèmes d'alarme -  Alarmanlagen -
Systèmes d'alarme intrusion - Einbruchmeldeanlagen -
Partie 4: Dispositifs d'avertissement Teil 4: Signalgeber






This Technical Specification was approved by CENELEC on 2006-05-25.

CENELEC members are required to announce the existence of this TS in the same way as for an EN and to
make the TS available promptly at national level in an appropriate form. It is permissible to keep conflicting
national standards in force.

CENELEC members are the national electrotechnical committees of Austria, Belgium, Cyprus, the Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia,
Spain, Sweden, Switzerland and the United Kingdom.



CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung

Central Secretariat: rue de Stassart 35, B - 1050 Brussels


© 2006 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. CLC/TS 50131-4:2006 E

---------------------- Page: 3 ----------------------

SIST-TS CLC/TS 50131-4:2007
CLC/TS 50131-4:2006 – 2 –
Foreword
This Technical Specification was prepared by the Technical Committee CENELEC TC 79, Alarm
systems.
The text of the draft was submitted to the formal vote and was approved by CENELEC as
CLC/TS 50131-4 on 2006-05-25.
The following date was fixed:
– latest date by which the existence of the CLC/TS
has to be announced at national level (doa) 2007-03-01
EN 50131 will consist of the following parts, under the general title “Alarm systems – Intrusion and
hold-up systems":
Part 1 System requirements
Part 2-2 Requirements for passive infrared detectors
Part 2-3 Requirements for microwave detectors
Part 2-4 Requirements for combined passive infrared and microwave detectors
Part 2-5 Requirements for combined passive infrared and ultrasonic detectors
Part 2-6 Requirements for opening contacts (magnetic)
Part 2-7 Intrusion detectors - Glass break detectors acoustic
Part 3 Control and indicating equipment
Part 4 Warning devices
Part 5-3 Requirements for interconnections equipment using radio frequency techniques
Part 6 Power supplies
Part 7 Application guidelines

---------------------- Page: 4 ----------------------

SIST-TS CLC/TS 50131-4:2007
– 3 – CLC/TS 50131-4:2006
Contents
1 Scope .4
2 Normative references .4
3 Definitions and abbreviations.5
3.1 Definitions.5
3.2 Abbreviations.6
4 Requirements .6
4.1 Functional.6
4.2 Tamper .8
4.3 Environmental.
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CLC
EN 50131-2-2:2021(Main)
Alarm systems - Intrusion and hold-up systems - Part 2-2: Requirements for passive infrared detectors
SIST EN 50131-2-2:2022

This document is for passive infrared detectors installed in buildings and provides for security grades 1 to 4 (see EN 50131 1), specific or non-specific wired or wire-free detectors, and uses environmental classes I to IV (see EN 50130 5). This document does not include requirements for detectors intended for use outdoors. The purpose of the detector is to detect the broad spectrum infrared radiation emitted by an intruder, to analyse the resulting signals and to provide the necessary range of signals or messages to be used by the rest of the intrusion alarm system. The grade-dependent requirements of this document apply and it is essential that a detector fulfils all the requirements of the specified grade. Functions additional to the mandatory functions specified in this document can be included in the detector, providing they do not influence the correct operation of the mandatory functions. Requirements for system interconnections are not included in this document.

  • Standard
    53 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 50131-6:2017/A1:2021(Amendment)
Alarm systems - Intrusion and hold-up systems - Part 6: Power supplies
SIST EN 50131-6:2018/A1:2021

This European Standard specifies the requirements, performance criteria and testing procedures for PS to be used as part of Intrusion and Hold up Alarm Systems. The PS will either be an integral part of an I&HAS component or stand-alone. The control functions of the PS may be incorporated as part of the PS device, or may be provided by another I&HAS component, e.g. a CIE. This European Standard is not applicable when the PS requirements for I&HAS components are included within the relevant product standard. The requirements correspond to each of the four security grades given in the European Standard EN 50131 1, Alarm Systems – Intrusion and Hold-Up Systems - Part 1: System requirements. Requirements are also given for four environmental classes covering applications in indoor and outdoor locations. This standard covers: a) mandatory functions which will be provided on all PS; and b) optional functions which may be provided. This European Standard does not deal with requirements for compliance with EC regulatory Directives, such as the EMC Directive, Low Voltage Directive, etc. except that it specifies the equipment operating conditions and reduced functional test for EMC susceptibility testing as required by EN 50130 4. Other functions associated with I&HAS not specified in this standard may be provided. Such functions will not affect the requirements of any mandatory or optional functions.

  • Amendment
    6 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 50131-2-4:2020(Main)
Alarm systems - Intrusion and hold-up systems - Part 2-4: Requirements for combined passive infrared and microwave detectors
SIST EN 50131-2-4:2020

This document is for combined passive infrared and microwave detectors installed in buildings and provides for security grades 1 to 4 (see EN 50131-1), specific or non-specific wired or wire-free detectors, and uses environmental classes I to IV (see EN 50130-5). This document does not include requirements for detectors intended for use outdoors. The purpose of the detector is to detect the broad spectrum infrared radiation emitted by an intruder, to emit microwave signals and analyse the signals that are returned and to provide the necessary range of signals or messages to be used by the rest of the intrusion alarm system. For a combined detector where both detection technologies need to be in their activated state in order to generate an alarm condition, the grade-dependent requirements of this document apply. For combined detectors which can be configured or operated such that each detection technology can generate an alarm condition independently, the grade-dependant requirements as defined in EN 50131 2 2 and EN 50131-2-3 apply, when configured accordingly. Otherwise, it is the responsibility of the manufacturer to clearly state that the detector does not comply to this document and not to EN 50131-2-2 and EN 50131 2-3 when put into such a configuration. It is essential that a detector fulfils all the requirements of the specified grade. Functions additional to the mandatory functions specified in this document can be included in the detector, providing they do not influence the correct operation of the mandatory functions. Requirements for system interconnections are not included in this document.

  • Standard
    54 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 50131-1:2006/A3:2020(Amendment)
Alarm systems - Intrusion and hold-up systems - Part 1: System requirements
SIST EN 50131-1:2007/A3:2020

This European Standard specifies the requirements for Intrusion and Hold-up Alarm Systems installed in buildings using specific or non-specific wired interconnections or wire-free interconnections. These requirements also apply to the components of an I&HAS installed in a building which are normally mounted on the external structure of a building e.g. ancillary control equipment or warning devices. The standard does not include requirements for exterior I&HAS. This standard specifies performance requirements for installed I&HAS but does not include requirements for design, planning, installation, operation or maintenance. These requirements also apply to I&HAS sharing means of detection, triggering, interconnection, control, communication and power supplies with other applications. The functioning of an I&HAS shall not be adversely influenced by other applications. Requirements are specified for I&HAS components where the relevant environment is classified. This classification describes the environment in which an I&HAS component may be expected to function as designed. When the requirements of the four environmental classes are inadequate, due to the extreme conditions experienced in certain geographic locations, special national conditions are given in Annex A. General environmental requirements for I&HAS components are described in Clause 7. The requirements of this European Standard also apply to IAS and HAS when these systems are installed independently. When an I&HAS does not include functions relating to the detection of intruders, the requirements relating to intrusion detection do not apply. When an I&HAS does not include functions relating to hold-up, the requirements relating to hold-up do not apply. NOTE Unless otherwise stated the abbreviation I&HAS is intended to also mean IAS and HAS.

  • Amendment
    11 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 50131-2-2:2017(Main)
Alarm systems - Intrusion and hold-up systems - Part 2-2: Intrusion detectors - Passive infrared detectors
SIST EN 50131-2-2:2018

This European Standard is for passive infrared detectors installed in buildings and provides for security grades 1 to 4 (see EN 50131-1), specific or non-specific wired or wire-free detectors, and uses environmental classes I to IV (see EN 50130-5). This European Standard does not include requirements for passive infrared detectors intended for use outdoors. It is essential that a detector fulfils all the requirements of the specified grade. Functions additional to the mandatory functions specified in this standard may be included in the detector, providing they do not influence the correct operation of the mandatory functions. This European Standard does not apply to system interconnections.

  • Standard
    45 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 50131-6:2017(Main)
Alarm systems - Intrusion and hold-up systems - Part 6: Power supplies
SIST EN 50131-6:2018

This European Standard specifies the requirements, performance criteria and testing procedures for PS to be used as part of Intrusion and Hold up Alarm Systems. The PS will either be an integral part of an I&HAS component or stand-alone. The control functions of the PS may be incorporated as part of the PS device, or may be provided by another I&HAS component, e.g. a CIE. This European Standard is not applicable when the PS requirements for I&HAS components are included within the relevant product standard. The requirements correspond to each of the four security grades given in the European Standard EN 50131 1, Alarm Systems - Intrusion and Hold-Up Systems - Part 1: System requirements. Requirements are also given for four environmental classes covering applications in indoor and outdoor locations. This standard covers: a) mandatory functions which will be provided on all PS; and b) optional functions which may be provided. This European Standard does not deal with requirements for compliance with EC regulatory Directives, such as the EMC Directive, Low Voltage Directive, etc. except that it specifies the equipment operating conditions and reduced functional test for EMC susceptibility testing as required by EN 50130 4. Other functions associated with I&HAS not specified in this standard may be provided. Such functions will not affect the requirements of any mandatory or optional functions.

  • Standard
    52 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 50131-1:2006/A2:2017(Amendment)
Alarm systems - Intrusion and hold-up systems - Part 1: System requirements
SIST EN 50131-1:2007/A2:2017

Harmonise system requirements with requirements for system components specified in standard published since EN 50131-1:2006 was published.

  • Amendment
    14 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 50131-5-3:2017(Main)
Alarm systems - Intrusion systems - Part 5-3: Requirements for interconnections equipment using radio frequency techniques
SIST EN 50131-5-3:2017

This European Standard applies to intrusion alarm equipment using radio frequency (RF) links and located on protected premises. It does not cover long-range radio transmissions. This European Standard defines the terms used in the field of intrusion alarm equipment using radio frequency links as well as the requirements relevant to the equipment.

  • Standard
    20 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
CLC/TS 50131-11:2012/IS1:2014
Alarm systems - Intrusion and hold-up systems - Part 11: Hold-up devices
SIST-TS CLC/TS 50131-11:2012/IS1:2014

This Technical Specification is for dedicated hold-up devices in buildings, e.g. deliberately operated hold-up devices which can be triggered to create a hold-up alarm signal or message. It provides four security Grades 1-4 (see EN 50131-1), specific or non specific wired or wire-free hold-up devices and uses Environmental Classes I-IV (see EN 50130-5). This Technical Specification does not include requirements for hold-up devices intended for use outdoors, or for mobile hold-up devices or for devices with functions additional to hold-up facility. NOTE If a device provides functions additional to hold-up facility, it is recommended to function similar to the requirement described in this Technical Specification. Functions additional to the mandatory functions as specified in this Technical Specification may be included in the hold-up device, providing they do not adversely influence the correct operation of the mandatory functions. This Technical Specification does not apply to system interconnections.

  • Addendum
    6 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
CLC/TS 50131-11:2012(Main)
Alarm systems - Intrusion and hold-up systems - Part 11: Hold-up devices
SIST-TS CLC/TS 50131-11:2012

This Technical Specification is for dedicated hold-up devices in buildings, e.g. deliberately operated hold-up devices which can be triggered to create a hold-up alarm signal or message. It provides four security Grades 1-4 (see EN 50131-1), specific or non specific wired or wire-free hold-up devices and uses Environmental Classes I-IV (see EN 50130-5). This Technical Specification does not include requirements for hold-up devices intended for use outdoors, or for mobile hold-up devices or for devices with functions additional to hold-up facility. NOTE If a device provides functions additional to hold-up facility, it is recommended to function similar to the requirement described in this Technical Specification. Functions additional to the mandatory functions as specified in this Technical Specification may be included in the hold-up device, providing they do not adversely influence the correct operation of the mandatory functions. This Technical Specification does not apply to system interconnections.

  • Technical specification
    37 pages
    English language
    sale 10% off
    e-Library read for
    1 day