iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CLC

EN 116000-3:1996

(Main)

Generic Specification: Electromechanical all-or-nothing relays - Part 3: Test and measurement procedures

Generic Specification: Electromechanical all-or-nothing relays - Part 3: Test and measurement procedures

Superseded by EN 61810-7:2006 (PR=16567)

Fachgrundspezifikation: Elektromechanische Schaltrelais - Teil 3: Prüf- und Meßverfahren

Spécification générique: Relais électromécaniques de tout-ou-rien - Partie 3: Méthodes d'essai et de mesure

Generic Specification: Electromechanical all-or-nothing relays - Part 3: Test and measurement procedures

General Information

Status
Withdrawn
Publication Date
05-Feb-1996
ICS
29.120.70 - Relays
Technical Committee
CLC/SR 94 - All-or-nothing electrical relays
Drafting Committee
IEC/TC 94 - IEC_TC_94
Parallel Committee
IEC/TC 94 - IEC_TC_94
Current Stage
9960 - Withdrawal effective - Withdrawal
Start Date
01-May-2009
Completion Date
01-May-2009
Ref Project
SIST EN 116000-3:2001 - Generic Specification: Electromechanical all-or-nothing relays -- Part 3: Test and measurement procedures

Relations

Replaced By
EN 61810-7:2006 - Electromechanical elementary relays - Part 7: Test and measurement procedures
Effective Date
28-Jan-2023

Buy Standard

EN 116000-3:2001EN 116000-3:2001
PreviousNext
Standard
EN 116000-3:2001
English language
63 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Generic Specification: Electromechanical all-or-nothing relays - Part 3: Test and measurement proceduresFachgrundspezifikation: Elektromechanische Schaltrelais -- Teil 3: Prüf- und MeßverfahrenSpécification générique: Relais électromécaniques de tout-ou-rien -- Partie 3: Méthodes d'essai et de mesureGeneric Specification: Electromechanical all-or-nothing relays -- Part 3: Test and measurement procedures29.120.70RelejiRelaysICS:Ta slovenski standard je istoveten z:EN 116000-3:1996SIST EN 116000-3:2001en01-september-2001SIST EN 116000-3:2001SLOVENSKI
STANDARD



SIST EN 116000-3:2001



SIST EN 116000-3:2001



SIST EN 116000-3:2001



SIST EN 116000-3:2001



SIST EN 116000-3:2001



SIST EN 116000-3:2001



SIST EN 116000-3:2001



SIST EN 116000-3:2001



SIST EN 116000-3:2001



SIST EN 116000-3:2001



SIST EN 116000-3:2001



SIST EN 116000-3:2001



SIST EN 116000-3:2001



SIST EN 116000-3:2001



SIST EN 116000-3:2001



SIST EN 116000-3:2001



SIST EN 116000-3:2001



SIST EN 116000-3:2001



SIST EN 11
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CLC
EN IEC 62246-4:2023(Main)
Reed switches - Part 4: Application in conjunction with magnetic actuator used for magnetic sensing devices
SIST EN IEC 62246-4:2023

IEC 62246-4:2023 gives additional requirements for the evaluation of functional characteristics on reed switching components operated by magnetic actuator and gives guidance for their implementation in selected applications. This document specifies test and measurement procedures for the application of reed switch (contact) based magnetic sensors. In case the application of a reed contact magnetic sensor determines additional requirements exceeding those specified in this document, the sensor is evaluated with this application in accordance with the relevant IEC or ISO standard(s) (e.g. IEC 62061 or ISO 13849 series, IEC 60335-1 and relevant parts of the IEC 60335-2 series, IEC 60730-1, IEC 61373, ISO 16750-3). This document does not apply to: – sensing or monitoring of the position of elements of interlocking devices for movable guards (see ISO 14119); – sensing or monitoring of the position of elements of pressure sensitive protective equipment (PSPE, see ISO 13856 series); – electrical equipment for measurement, control, and laboratory use (see IEC 61010-1); – aircraft – proximity switches (see ISO 6859-1). Information contained in this document is relevant to the application of a magnetic sensor on new installations as well as modifications to existing installations.

  • Standard
    75 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    58 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 61810-4:2020(Main)
Electromechanical elementary relays - Part 4: General and safety requirements for reed relays
SIST EN IEC 61810-4:2021

IEC 61810-4:2020 applies to electromechanical elementary relays with reed switches (reed contacts) incorporated into general control circuits. It defines the basic functional and safety requirements in all areas of electrical engineering or electronics in accordance with the parts of IEC 61810 series and IEC 62246 series. IEC 61810-4:2020 defines technical deviations/additions to IEC 61810-1. It specifies type tests, routine tests, special tests and environmental tests to confirm the service conditions for applications.

  • Standard
    32 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    25 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 61810-1:2015/A1:2020(Amendment)
Electromechanical elementary relays - Part 1: General and safety requirements
SIST EN 61810-1:2015/A1:2021
  • Amendment
    4 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 61810-10:2019(Main)
Electromechanical elementary relays - Part 10: Additional functional aspects and safety requirements for high-capacity relays
SIST EN IEC 61810-10:2021

IEC 61810-10:2019, with functional and safety aspects, applies to electromechanical elementary relays (non-specified time all-or-nothing relays) with high capability requirements like breaking or short circuit capabilities and similar for incorporation into low-voltage equipment. These relays may have a specific design to extinguish the electric arc between contacts (e.g. by magnetic blow-out), or use an insulation coordination not covered by IEC 61810-1 (e.g. by gas filled contact chambers), or require safety assessments not covered by IEC 61810-1 (e.g. for higher loads). It defines additional requirements for high-capacity relays with generic performance intended for use in applications in smart grids, electric vehicles and other applications where, for example, battery charge/discharge switching is used, such as: • electrical energy storage (EES) systems, • solar photovoltaic energy systems, • electric road vehicles (EV) and electric industrial trucks, • power electronic systems and equipment, • secondary cells and batteries, • road vehicles. Compliance with the requirements of this standard is verified by the type tests indicated.

  • Standard
    65 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 62246-1-1:2018(Main)
Reed switches - Part 1-1: Generic specification - Blank detail specification
SIST EN IEC 62246-1-1:2018

IEC 62246-1-1:2018 is a blank detail specification which defines requirements and tests for reed switches for use in general and industrial applications. This document is intended to be used in conjunction with IEC 62246-1:2015 and specific products standards applying as switching elements. This document selects from IEC 62246-1:2015 and from other sources the appropriate test procedures to be used in detail specifications derived from this specification. Reed switch types are specified depending on characteristic values including functional ratings for safety and tests. This second edition cancels and replaces the first edition published in 2013. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous editions: a) update of the scope, references and terms and definitions; b) inclusion of guidelines for the preparation of blank detail and detail specifications; c) update of characteristics values including functional ratings for safety; d) update of the quality conformance inspection procedures; e) update of typical applications.

  • Standard
    64 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 61810-1:2015/AC:2018-04(Corrigendum)
Electromechanical elementary relays - Part 1: General and safety requirements
SIST EN 61810-1:2015/AC:2018

2018-04 AJC - IEC published corrigendum.

  • Corrigendum
    3 pages
    English and French language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 61810-2-1:2017(Main)
Electromechanical elementary relays - Part 2-1: Reliability - Procedure for the verification of B10 values
SIST EN 61810-2-1:2018

IEC 61810-2-1:2017 specifies reliability test procedures for electromechanical elementary relays when enhanced requirements for the verification of reliability apply. Particular provisions are given for relays incorporated in safety-related control systems of machinery in accordance with IEC 62061 and ISO 13849-1. For such relays, B10 values for dangerous failures (B10D values) are derived from the tests specified in this document. This edition includes the following significant technical changes with respect to the previous edition: - limitation of tests to 10 M cycles in Clause 5; - reduction of required number of test samples to 5 in specified cases; - introduction of WeiBayes analysis for routine test under Clause 4.

  • Standard
    20 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 61810-2:2017(Main)
Electromechanical elementary relays - Part 2: Reliability
SIST EN 61810-2:2018

IEC 61810-2:2017 covers test conditions and provisions for the evaluation of endurance tests using appropriate statistical methods to obtain reliability characteristics for relays. This document applies to electromechanical elementary relays considered as non-repaired items (i.e. items which are not repaired after failure). This document does not cover procedures for electromechanical elementary relays where enhanced requirements for the verification of reliability apply. This edition includes the following significant technical changes with respect to the previous edition: - not only graphical but also numerical methods are added; - reduction of number of samples in specified cases; - new subclauses of confidence intervals are added; - the WeiBayes approach is added to facilitate compliance tests (routine test) with lower effort; - annexes have been restructured into an Annex A for data analysis (normative) and Annex B (informative) where various examples of the data analysis are given; - the former Annex C has been incorporated into the modified Annex B; - a new Annex C replaces the old Annex D.

  • Standard
    45 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 61810-1:2015/AC:2017-07(Corrigendum)
Electromechanical elementary relays - Part 1: General and safety requirements
SIST EN 61810-1:2015/AC:2017
  • Corrigendum
    3 pages
    English and French language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 61810-3:2015(Main)
Electromechanical elementary relays - Part 3: Relays with forcibly guided (mechanically linked) contacts
SIST EN 61810-3:2015

IEC 61810-3:2015 specifies special requirements and tests for elementary relays with forcibly guided contacts, also known as mechanically linked contacts. These special requirements apply in addition to the general requirements of IEC 61810-1.

  • Standard
    14 pages
    English language
    sale 10% off
    e-Library read for
    1 day