EN 60793-1-43:2002
(Main)Optical fibres - Part 1-43: Measurement methods and test procedures - Numerical aperture
Optical fibres - Part 1-43: Measurement methods and test procedures - Numerical aperture
Establishes requirements for measuring the numerical aperture of category A1 graded-index multimode fibre, and its light-gathering ability. This is used to predict lauching efficiency, joint loss at splices, and micro/macrobending perfprmance.
Lichtwellenleiter - Teil 1-43: Messmethoden und Prüfverfahren - Numerische Apertur
Fibres optiques - Partie 1-43: Méthodes de mesure et procédures d'essai - Ouverture numérique
Etablit des prescriptions pour mesurer l'ouveture numérique d'une fibre multimodale à gradient d'indice catégorie A1, et sa capacité à capter la lumière. Il est utilisé pour prévoir l'efficacité de l'injection, les pertes aux épissures et la tenue aux micorcourbures et aux macrocourbures.
Optična vlakna – 1-43. del: Metode merjenja in preskusni postopki - Numerična odprtina (IEC 60793-1-43:2001)*
General Information
Relations
Standards Content (Sample)
SLOVENSKI SIST EN 60793-1-43:2004
STANDARD
september 2004
Optična vlakna – 1-43. del: Metode merjenja in preskusni postopki -
Numerična odprtina (IEC 60793-1-43:2001)*
Optical fibres - Part 1-43: Measurement methods and test procedures - Numerical
aperture (IEC 60793-1-43:2001)
ICS 33.180.10 Referenčna številka
© Standard je založil in izdal Slovenski inštitut za standardizacijo. Razmnoževanje ali kopiranje celote ali delov tega dokumenta ni dovoljeno
EUROPEAN STANDARD EN 60793-1-43
NORME EUROPÉENNE
EUROPÄISCHE NORM February 2002
ICS 33.180.10 Partly supersedes EN 188000:1992
English version
Optical fibres
Part 1-43: Measurement methods and test procedures –
Numerical aperture
(IEC 60793-1-43:2001)
Fibres optiques Lichtwellenleiter
Partie 1-43: Méthodes de mesure Teil 1-43: Messmethoden
et procédures d'essai – und Prüfverfahren –
Ouverture numérique Numerische Apertur
(CEI 60793-1-43:2001) (IEC 60793-1-43:2001)
This European Standard was approved by CENELEC on 2001-10-01. CENELEC members are bound to
comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the Central Secretariat or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and
notified to the Central Secretariat has the same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Czech Republic,
Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands,
Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.
CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
Central Secretariat: rue de Stassart 35, B - 1050 Brussels
© 2002 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 60793-1-43:2002 E
Foreword
The text of document 86A/672/FDIS, future edition 1 of IEC 60793-1-43, prepared by SC 86A, Fibres
and cables, of IEC TC 86, Fibre optics, was submitted to the IEC-CENELEC parallel vote and was
approved by CENELEC as EN 60793-1-43 on 2001-10-01.
This European Standard supersedes subclause 4.19 (test method 311) of EN 188000:1992.
The following dates were fixed:
– latest date by which the EN has to be implemented
at national level by publication of an identical
national standard or by endorsement (dop) 2002-09-01
– latest date by which the national standards conflicting
with the EN have to be withdrawn (dow) 2004-10-01
Compared to IEC 60793-1:1989 and IEC 60793-2:1992, IEC/SC 86A has adopted a revised structure
of the new IEC 60793 series: The individual measurement methods and test procedures for optical
fibres are published as "Part 1-XX"; the product standards are published as "Part 2-XX".
The general relationship between the new series of EN 60793 and the superseded European
Standards of the EN 188000 series is as follows:
EN Title supersedes
EN 60793-1-XX Optical fibres -- Part 1-XX: Measurement methods Individual subclauses of
and test procedures EN 188000:1992
EN 188100:1995
EN 60793-2-XX Optical fibres -- Part 2-XX: Product specifications
EN 188101:1995
EN 188102:1995
EN 188200:1995
EN 188201:1995
EN 188202:1995
EN 60793-1-4X consists of the following parts, under the general title: Optical fibres:
- Part 1-40: Measurement methods and test procedures – Attenuation
- Part 1-41: Measurement methods and test procedures – Bandwidth
- Part 1-42: Measurement methods and test procedures – Chromatic dispersion
- Part 1-43: Measurement methods and test procedures – Numerical aperture
- Part 1-44: Measurement methods and test procedures – Cut-off wavelength
- Part 1-45: Measurement methods and test procedures – Mode field diameter
- Part 1-46: Measurement methods and test procedures – Monitoring of changes in optical
transmittance
- Part 1-47: Measurement methods and test procedures – Macrobending loss
- Part 1-48: Measurement methods and test procedures – Under consideration
- Part 1-49: Measurement methods and test procedures – Under consideration
__________
Endorsement notice
The text of the International Standard IEC 60793-1-43:2001 was approved by CENELEC as a European
Standard without any modification.
__________
NORME CEI
INTERNATIONALE IEC
60793-1-43
INTERNATIONAL
Première édition
STANDARD
First edition
2001-07
Fibres optiques –
Partie 1-43:
Méthodes de mesure et procédures d'essai –
Ouverture numérique
Optical fibres –
Part 1-43:
Measurement methods and test procedures –
Numerical aperture
IEC 2001 Droits de reproduction réservés Copyright - all rights reserved
Aucune partie de cette publication ne peut être reproduite ni No part of this publication may be reproduced or utilized in
utilisée sous quelque forme que ce soit et par aucun procédé, any form or by any means, electronic or mechanical,
électronique ou mécanique, y compris la photocopie et les including photocopying and microfilm, without permission in
microfilms, sans l'accord écrit de l'éditeur. writing from the publisher.
International Electrotechnical Commission 3, rue de Varembé Geneva, Switzerland
Telefax: +41 22 919 0300 e-mail: inmail@iec.ch IEC web site http://www.iec.ch
CODE PRIX
Commission Electrotechnique Internationale
M
PRICE CODE
International Electrotechnical Commission
Pour prix, voir catalogue en vigueur
For price, see current catalogue
60793-1-43 © IEC:2001 – 3 –
CONTENTS
FOREWORD.5
INTRODUCTION.9
1 Scope.11
2 Normative references.11
3 Overview of method .11
4 Reference test method.13
5 Apparatus.13
5.1 Input system .13
5.1.1 Light source.13
5.1.2 Input optics.13
5.1.3 Fibre input end support and alignment.13
5.1.4 Cladding mode stripper .13
5.2 Output system and detection.13
5.2.1 Technique 1 – Angular scan (see figure 1) .15
5.2.2 Technique 2 – Angular scan (see figure 2) .15
5.2.3 Technique 3 – Scan of the spatial field pattern (see figure 3).15
5.2.4 Optical detector .21
6 Sampling and specimens .21
6.1 Specimen length.21
6.2 Specimen end face .21
7 Procedure.21
8 Calculations.23
8.1 Far field versus maximum theoretical value.23
8.2 Five per cent intensity angle, θθ .23
θθ
8.3 Numerical aperture, NA .23
ff
9 Results .23
9.1 Information to be provided with each measurement.23
9.2 Information available upon request .23
10 Specification information.25
Figure 1 – Technique 1 – Angular scan.17
Figure 2 – Technique 2 – Angular scan.17
Figure 3 – Technique 3 – Scan of the spatial field pattern .19
60793-1-43 © IEC:2001 – 5 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
___________
OPTICAL FIBRES –
Part 1-43: Measurement methods and test procedures –
Numerical aperture
FOREWORD
1) The IEC (International Electrotechnical Commission) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of the IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, the IEC publishes International Standards. Their preparation is
entrusted to technical committees; any IEC National Committee interested in the subject dealt with may
participate in this preparatory work. International, governmental and non-governmental organizations liaising
with the IEC also participate in this preparation. The IEC collaborates closely with the International Organization
for Standardization (ISO) in accordance with conditions determined by agreement between the two
organizations.
2) The formal decisions or agreements of the IEC on technical matters express, as nearly as possible, an
international consensus of opinion on the relevant subjects since each technical committee has representation
from all interested National Committees.
3) The documents produced have the form of recommendations for international use and are published in the form
of standards, technical specifications, technical reports or guides and they are accepted by the National
Committees in that sense.
4) In order to promote international unification, IEC National Committees undertake to apply IEC International
Standards transparently to the maximum extent possible in their national and regional standards. Any
divergence between the IEC Standard and the corresponding national or regional standard shall be clearly
indicated in the latter.
5) The IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any
equipment declared to be in conformity with one of its standards.
6) Attention is drawn to the possibility that some of the elements of this International Standard may be the subject
of patent rights. The IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 60793-1-43 has been prepared by subcommittee 86A: Fibres and
cables, of IEC technical committee 86: Fibre optics.
This standard, together with the other standards in the IEC 60793-1-4X series, replaces
the second edition of IEC 60793-1-4, of which it constitutes a technical revision.
The text of this standard is based on the following documents:
FDIS Report on voting
86A/672/FDIS 86A/696/RVD
Full information on the voting for the approval of this standard can be found in the report on
voting indicated in the above table.
This publication has been drafted in accordance with the ISO/IEC Directives, Part 3.
IEC 60793-1-1 and IEC 60793-1-2 cover generic specifications.
60793-1-43 © IEC:2001 – 7 –
IEC 60793-1-4X consists of the following parts, under the general title: Optical fibres:
– Part 1-40: Measurement methods and test procedures – Attenuation
– Part 1-41: Measurement methods and test procedures – Bandwidth
– Part 1-42: Measurement methods and test procedures – Chromatic dispersion
– Part 1-43: Measurement methods and test procedures – Numerical aperture
– Part 1-44: Measurement methods and test procedures – Cut-off wavelength
– Part 1-45: Measurement methods and test procedures – Mode field diameter
– Part 1-46: Measurement methods and test procedures – Monitoring of changes in optical
transmittance
– Part 1-47: Measurement methods and test procedures – Macrobending loss
– Part 1-48: Measurement methods and test procedures – Under consideration
– Part 1-49: Measurement methods and test procedures – Under consideration
The committee has decided that the contents of this publication will remain unchanged until
2003. At this date, the publication will be
• reconfirmed;
• withdrawn;
• replaced by a revised edition, or
• amended.
60793-1-43 © IEC:2001 – 9 –
INTRODUCTION
Publications in the IEC 60793-1 series concern measurement methods and test procedures as
they apply to optical fibres.
Within the same series several different areas are grouped, as follows:
– parts 1-10 to 1-19: General
– parts 1-20 to 1-29: Measurement methods and test procedures for dimensions
– parts 1-30 to 1-39: Measurement methods and test procedures for mechanical charac-
teristics
– parts 1-40 to 1-49: Measurement methods and test procedures for transmission and optical
characteristics
– parts 1-50 to 1-59: Measurement methods and test procedures for environmental charac-
teristics.
60793-1-43 © IEC:2001 – 11 –
OPTICAL FIBRES –
Part 1-43: Measurement methods and test pr
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.