prEN IEC 61169-64:2025
(Main)Radio frequency connectors - Part 64: Sectional specification - RF coaxial connectors with 0,8 mm inner diameter of outer conductor - Characteristic impedance 50 ω (type 0,8)
Radio frequency connectors - Part 64: Sectional specification - RF coaxial connectors with 0,8 mm inner diameter of outer conductor - Characteristic impedance 50 ω (type 0,8)
Hochfrequenz-Steckverbinder - Teil 64: Rahmenspezifikation für koaxiale HF-Steckverbinder mit 0,8 mm Innendurchmesser des Außenleiters - Wellenwiderstand 50 Ω (Typ 0,8)
Connecteurs pour fréquences radioélectriques - Partie 64: Spécification intermédiaire - Connecteurs RF coaxiaux avec un conducteur extérieur disposant d’un diamètre intérieur de 0,8 mm - Impédance caractéristique de 50 ω (type 0,8)
Radiofrekvenčni konektorji - 64. del: Področna specifikacija - Radiofrekvenčni (RF) koaksialni konektorji z notranjim premerom 0,8 mm zunanjega vodnika - Karakteristična impedanca 50 ohm (tip 0,8)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-maj-2025
Radiofrekvenčni konektorji - 64. del: Področna specifikacija - Radiofrekvenčni (RF)
koaksialni konektorji z notranjim premerom 0,8 mm zunanjega vodnika -
Karakteristična impedanca 50 ohm (tip 0,8)
Radio frequency connectors - Part 64: Sectional specification - RF coaxial connectors
with 0,8 mm inner diameter of outer conductor - Characteristic impedance 50 ω (type
0,8)
Hochfrequenz-Steckverbinder - Teil 64: Rahmenspezifikation für koaxiale HF-
Steckverbinder mit 0,8 mm Innendurchmesser des Außenleiters - Wellenwiderstand 50
Ω (Typ 0,8)
Connecteurs pour fréquences radioélectriques - Partie 64: Spécification intermédiaire -
Connecteurs RF coaxiaux avec un conducteur extérieur disposant d’un diamètre
intérieur de 0,8 mm - Impédance caractéristique de 50 ω (type 0,8)
Ta slovenski standard je istoveten z: prEN IEC 61169-64:2025
ICS:
33.120.30 Radiofrekvenčni konektorji RF connectors
(RF)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
46F/696/CDV
COMMITTEE DRAFT FOR VOTE (CDV)
PROJECT NUMBER:
IEC 61169-64 ED2
DATE OF CIRCULATION: CLOSING DATE FOR VOTING:
2025-02-28 2025-05-23
SUPERSEDES DOCUMENTS:
46F/673/CD, 46F/681/CC
IEC SC 46F : RF AND MICROWAVE PASSIVE COMPONENTS
SECRETARIAT: SECRETARY:
United States of America Mr John Morelli
OF INTEREST TO THE FOLLOWING COMMITTEES: HORIZONTAL FUNCTION(S):
ASPECTS CONCERNED:
SUBMITTED FOR CENELEC PARALLEL VOTING NOT SUBMITTED FOR CENELEC PARALLEL VOTING
Attention IEC-CENELEC parallel voting
The attention of IEC National Committees, members of CENELEC,
is drawn to the fact that this Committee Draft for Vote (CDV) is
submitted for parallel voting.
The CENELEC members are invited to vote through the CENELEC
online voting system.
This document is still under study and subject to change. It should not be used for reference purposes.
Recipients of this document are invited to submit, with their comments, notification of any relevant patent rights of which they are aware
and to provide supporting documentation.
Recipients of this document are invited to submit, with their comments, notification of any relevant “In Some Countries” clau ses to be
included should this proposal proceed. Recipients are reminded that the CDV stage is the final stage for submitting ISC c lauses. (SEE
AC/22/2007 OR NEW GUIDANCE DOC).
TITLE:
Radio frequency connectors – Part 64: Sectional specification – RF coaxial connectors with 0,8 mm inner
diameter of outer conductor – Characteristic impedance 50 Ω (type 0,8)
PROPOSED STABILITY DATE: 2028
NOTE FROM TC/SC OFFICERS:
Revised document by German NC for submission
electronic file, to make a copy and to print out the content for the sole purpose of preparing National Committee positions.
You may not copy or "mirror" the file or printed version of the document, or any part of it, for any other purpose without
permission in writing from IEC.
46F/696/CDV – 2 – IEC CDV 61169-64 © IEC 2025
CONTENTS
FOREWORD . 4
1 Scope . 6
2 Normative references . 6
3 Terms and definitions . 7
4 Mating face and gauge information . 7
4.1 Material . 7
4.2 Reference position . 7
4.3 Datum system . 7
4.4 Dimensions – High performance connector – Grade 1 . 8
4.4.1 Connector with pin centre contact – Grade 1 . 8
4.4.2 Connector with socket centre contact – Grade 1 . 9
4.5 Dimensions – Standard test connector – Grade 0. 10
4.5.1 Connector with pin centre contact – Grade 0 . 10
4.5.2 Connector with socket centre contact – Grade 0 . 11
4.6 Optional design of coupling nut . 12
4.7 Gauging of socket centre contacts . 12
4.7.1 Gauge pins . 12
4.7.2 Test sequence . 13
5 Quality assessment procedures . 14
5.1 General . 14
5.2 Ratings and characteristics . 14
5.3 Test schedule and inspection requirements. 15
5.3.1 Acceptance tests . 15
5.3.2 Periodic tests . 15
5.4 Procedures for quality conformance . 15
5.4.1 Quality conformance inspection . 15
5.4.2 Quality conformance and its maintenance . 15
6 Instructions for preparation of detail specifications . 16
6.1 General . 16
6.2 Identification of the component . 16
6.3 Performance . 16
6.4 Marking, ordering information and related matters . 16
6.5 Selection of tests, test conditions and severities . 16
6.6 Blank detail specification pro-forma for type 0,8 connectors . 16
7 Marking . 16
7.1 Marking of component . 16
7.2 Marking and contents of package . 16
Bibliography . 17
Figure 1 – Connector with pin centre contact – Grade 1 . 8
Figure 2 – Connector with socket centre contact – Grade 1 . 9
Figure 3 – Connector with pin centre contact – Grade 0 . 10
Figure 4 – Connector with socket centre contact – Grade 0 . 11
Figure 5 – Optional design of coupling nut . 12
Figure 6 – Gauge pin for socket centre contact . 12
IEC CDV 61169-64 © IEC 2025 – 3 – 46F/696/CDV
Table 1 – Dimensions of connector with pin centre contact – Grade 1 . 8
Table 2 – Dimensions of connector with socket centre contact – Grade 1 . 9
Table 3 – Dimensions of connector with pin centre contact – Grade 0 . 10
Table 4 – Dimensions of connector with socket centre contact – Grade 0 . 11
Table 5 – Dimensions of gauge pins for socket centre contact . 12
Table 6 – Ratings and characteristics . 14
46F/696/CDV – 4 – IEC CDV 61169-64 © IEC 2025
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
RADIO-FREQUENCY CONNECTORS –
Part 64: Sectional specification – RF coaxial connectors with 0,8 mm inner
diameter of outer conductor – Characteristic impedance 50 Ω (type 0,8)
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organisation for standardisation comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international
co-operation on all questions concerning standardisation in the electrical and electronic fields. To this end and
in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports,
Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their
preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with
may participate in this preparatory work. International, governmental, and non-governmental organisations
liaising with the IEC also participate in this preparation. IEC collaborates closely with the International
Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two
organisations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence between
any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants, or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) a nd
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent
rights. IEC shall not be held responsible for identifying any or all such patent rights.
IEC 61169-64 has been prepared by subcommittee 46F: RF and microwave passive
components, of IEC technical committee 46: Cables, wires, waveguides, RF connectors, RF
and microwave passive components and accessories. It is an International Standard.
This second edition cancels and replaces the first edition published in 2019. This edition
constitutes a major technical revision.
This edition includes the following significant technical changes with respect to the previous
edition:
a) upgrading of the inferior connector class to a grade 1 “high performance connector”;
b) alignment of the mating face dimensions as well as the ratings and characteristics with
the precision 0.8 mm connectors specified in the IEEE 287.1-2021 and IEEE 287.3-
2021 standards;
IEC CDV 61169-64 © IEC 2025 – 5 – 46F/696/CDV
c) Figures: true-to-scale design; change of datum system for tolerances; introduction of an
additional dimension;
d) gauge pins: correction of dimensions and test procedures;
e) simplification of the sections on quality assessment (clause 5), preparation of a detail
specification (clause 6), and marking (clause 7) by making direct reference to the
generic specification IEC 61169-1:2013;
f) introduction of an optional design for the coupling nut.
The text of this standard is based on the following documents:
FDIS Report on voting
46F/XXX/XXx 46F/XXX/XX
Full information on the voting for the approval of this International Standard can be found in the
report on voting indicated in the above table.
The language used for the development of this International Standard is English.
This document was drafted in accordance with ISO/IEC Directives, Part 2, and developed in
accordance with ISO/IEC Directives, Part 1 and ISO/IEC Directives, IEC Supplement, available
at www.ie
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.