EN 60154-1:1994

Flanges for waveguides - Part 1: General requirements

Relates to the dimensions of waveguides and flanges for use in electronic equipment. Covers requirements for flanges drilled before or after mounting of waveguide. Specifies waveguide flange mechanical requirements necessary to ensure compatibility and, as far as practicable, interchangeability as well as to ensure adequate electrical performance.

Flansche für Hohlleiter - Teil 1: Allgemeine Anforderungen

Brides pour guides d'ondes - Partie 1: Prescriptions générales

Se rapporte aux dimensions des guides d'ondes et de leurs brides qui sont utilisés dans les équipements électroniques. Couvre les prescriptions applicables aux brides percées avant ou après montage sur les guides d'ondes. Spécifie les prescriptions mécaniques applicables aux brides de guides d'ondes qui sont nécessaires pour assurer la compatibilité et, autant qu'il est possible de le faire, l'interchangeabilité ainsi que pour assurer des performances électriques suffisantes.

Flanges for waveguides - Part 1: General requirements (IEC 60154-1:1982)

General Information

• Status: Withdrawn
• Publication Date: 17-Nov-1994
• Withdrawal Date: 17-May-1995
• ICS: 33.120.10 - Coaxial cables. Waveguides
• Technical Committee: CLC/SR 46F - RF and microwave passive components
• Drafting Committee: IEC/SC 46F - IEC_SC_46F
• Parallel Committee: IEC/SC 46F - IEC_SC_46F
• Current Stage: 9960 - Withdrawal effective - Withdrawal
• Start Date: 22-Jun-2019
• Completion Date: 22-Jun-2019
• Ref Project: SIST EN 60154-1:1998 - Flanges for waveguides -- Part 1: General requirements

Relations

• Replaced By: EN 60154-1:2016 - Flanges for waveguides - Part 1: General requirements
• Effective Date: 07-Jun-2022
• Amended By: EN 60154-1:1994/A1:1994 - Flanges for waveguides - Part 1: General requirements
• Effective Date: 29-Jan-2023

Standards Content (Sample)

SLOVENSKI STANDARD
01-april-1998
Flanges for waveguides - Part 1: General requirements (IEC 60154-1:1982)
Flanges for waveguides -- Part 1: General requirements
Flansche für Hohlleiter -- Teil 1: Allgemeine Anforderungen
Brides pour guides d'ondes -- Partie 1: Prescriptions générales
Ta slovenski standard je istoveten z: EN 60154-1:1994
ICS:
33.120.10 Koaksialni kabli. Valovodi Coaxial cables. Waveguides
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

NORME
CEI
INTERNATIONALE
IEC
60154-1
INTERNATIONAL
Deuxième édition
STANDARD
Second edition
1982-01
Brides pour guides d'ondes
Première
partie:
Prescriptions
générales
Flanges for waveguides
Part 1:
General requirements
© IEC 1982 Droits
de reproduction réservés — Copyright - all rights reserved
Aucune partie de cette publication ne peut être reproduite ni No part of this publication may be reproduced or utilized in
utilisée sous quelque forme que ce soit et par aucun any form or by any means, electronic or mechanical,
procédé, électronique ou mécanique, y compris la photo- including photoco pying and microfilm, without permission in
copie et les microfilms, sans l'accord écrit de l'éditeur. writing from the publisher.
International Electrotechnical Commission 3, rue de Varembé Geneva, Switzerland
Telefax: [phone] e-mail: [e-mail] IEC web site http: //www.iec.ch
CODE PRIX
Commission Electrotechnique Internationale
G
PRICE CODE
International Electrotechnical Commission
IEC
MensayHapogHan 3neKTporexHKVecKaR KOMKCCHA
Pour prix, voir catalogue en vigueur
• •
For price, see current catalogue

154-1 © IEC 1982 3
CONTENTS
Page
FOREWORD
PREFACE
SCOPE
OBJECT
Clause
1. General
1.1 Terminology 7
1.2 Flange designation 7
1.3 Standard atmospheric conditions for testing 9
1.4 Visual inspection 9
2. Mechanical requirements 9
2.1 General requirements both for mounted and unmounted flanges 9
2.2 General requirements for mounted flanges (assemblies) 13
2.3 Additional requirements for unmounted flanges 13

154-1 © IEC 1982 — 5 —
INTERNATIONAL ELECTROTECHNICAL COMMISSION
FLANGES FOR WAVEGUIDES
Part 1: General requirements
FOREWORD
I) The formal decisions or agreements of the I EC on technical matters, prepared by Technical Committees on which all the National
Committees having a special interest therein are represented, express, as nearly as possible, an international consensus of opinion
on the subjects dealt with.
They have the form of recommendations for inte
2) rnational use and they are accepted by the National Committees in that
sense.
3) In order to promote inte rnational unification, the I EC expresses the wish that all National Committees should adopt the text of
the IEC recommendation for their national rules in so far as national conditions will permit. Any divergence between the IEC
recommendation and the corresponding national rules should, as far as possible, be clearly indicated in the latter.
4) The I EC has not laid down any procedure concerning marking as an
indication of approval and has no responsibility when an
item of equipment is declared to comply with one of its recommendations.
PREFACE
This standard has been prepared by Sub-Committee 46B: Waveguides and their Accessories, of IEC Technical Committee
No. 46: Cables, Wires and Waveguides for Telecommunication Equipment.
It forms the second edition of Pa rt 1 of I EC Publication 154 dealing with flanges for waveguides.
Detail information on the specific types of flanges is given in the relevant specifications issued as separate publications.
A draft amending the scope was circulated to the National Committees for comment under the Accelerated Procedure in January
1978. Subsequently, a draft, Document 46B(Central Office)88, was submitted to the National Committees for approval under the Six
Months' Rule in October 1980.
The National Committees of the following countries voted explicitly in favour of publication:
Belgium Sweden
Egypt Switzerland
France Turkey
German Democratic Republic Union of Soviet
Germany Socialist Republics
Poland United Kingdom
Spain United States of America
Other IEC publications quoted in this standard:
Publications Nos. 50(726): International Electrotechnical Vocabulary (LE.V.) Chapter 726: Transmission Lines and Wave-
guides.
68: Basic Environmental Testing Procedures.
153: Hollow Metallic Waveguides. 
Other publication quoted:
ISO Recommendation R 286: ISO System of Limits and Fits — Part 1: General, Tolerances and Deviations.

154-1 © IEC 1982 — 7
FLANGES FOR WAVEGUIDES
Part 1: General requirements
This standard takes into account, when necessary, I EC Publication 68: Basic Environmental Testing
Procedures and shall be used in conjunction with I EC Publication 153: Hollow Metallic Waveguide, and
ISO Recommendation R 286.
When there is a difference between the general requirements and the relevant specifications, the latter
shall prevail.
SCOPE
This standard relates to the dimensions of waveguide flanges for use in electronic equipment.
It covers requirements for flanges drilled before or after mounting on waveguides. It should be noted
that for optimum electrical performance, post-drilling of the alignment holes after mounting is recom-
mended.
OBJECT
The aim of this standard is to specify for waveguide flanges the mechanical requirements necessary to
ensure compatibility and, as far as practicable, interchangeability as well as to ensure adequate electrical
performance.
1. General
1.1
Terminology
In accordance with I EC Publication 50(726): Inte rnational Electrotechnical Vocabulary (I.E.V.),
Chapter 726: Transmission Lines and Waveguides.
1.2 Flange designation
Waveguide flanges covered by this standard shall be indicated by a reference number comprising
the following information:
a) the number of the present I EC publication (154);
b) the letters "IEC" ;
c) a dash;
d) a lette
...