CLC/TR 62453-51-60:2019
(Main)Field device tool (FDT) interface specification - Part 51-60: Communication implementation for common object model - IEC 61784 CPF 6
Field device tool (FDT) interface specification - Part 51-60: Communication implementation for common object model - IEC 61784 CPF 6
IEC TR 62453-51-60:2017(E) provides information for integrating the INTERBUS® technology into the COM-based implementation of FDT interface specification (IEC TR 62453-41). This part of IEC 62453 specifies implementation of communication and other services based on IEC 62453‑306. This document neither contains the FDT specification nor modifies it.
Field Device Tool (FDT)-Schnittstellenspezifikation - Teil 51-60: Kommunikationsimplementierung mit dem allgemeinen Objektmodell (COM) - Kommunikationsprofilfamilie (CPF) 6 nach IEC 6178
This part of the IEC 62453-51-xy series, which is a Technical Report, provides information for integrating the INTERBUS®1 technology into the COM-based implementation of FDT interface specification (IEC TR 62453-41). This part of IEC 62453 specifies implementation of communication and other services based on IEC 62453-306. This document neither contains the FDT specification nor modifies it.
Spécification des interfaces des outils des dispositifs de terrain (FDT) - Partie 51-60: Mise en œuvre d’un profil de communication pour le modèle d’objet commun - CPF 6 de l’IEC 61784
Specifikacija vmesnika orodja procesne naprave - 51-60. del: Implementacija komunikacije za skupni model objekta - IEC 61784 CPF 6 (IEC/TR 62453-51-60:2017)
Ta del skupine standardov IEC 62453-51-xy je tehnično poročilo, ki podaja informacije za integracijo tehnologije INTERBUS®1 v implementacijo (na osnovi COM) specifikacije vmesnika orodja procesne naprave (FDT) (IEC TR 62453-41).
Ta del standarda IEC 62453 določa implementacijo komunikacijskih in drugih storitev, ki temeljijo na standardu IEC 62453-306.
Ta dokument ne vsebuje specifikacije orodja procesne naprave niti je ne spreminja.
General Information
Standards Content (Sample)
SLOVENSKI STANDARD
01-junij-2019
Specifikacija vmesnika orodja procesne naprave - 51-60. del: Implementacija
komunikacije za skupni model objekta - IEC 61784 CPF 6 (IEC/TR 62453-51-
60:2017)
Field device tool (FDT) interface specification - Part 51-60: Communication
implementation for common object model - IEC 61784 CPF 6 (IEC/TR 62453-51-
60:2017)
Field Device Tool (FDT)-Schnittstellenspezifikation - Teil 51-60:
Kommunikationsimplementierung mit dem allgemeinen Objektmodell (COM) -
Kommunikationsprofilfamilie (CPF) 6 nach IEC 6178 (IEC/TR 62453-51-60:2017)
Spécification des interfaces des outils des dispositifs de terrain (FDT) - Partie 51-60:
Mise en oeuvre d'un profil de communication pour le modèle d'objet commun - CPF 6 de
l'IEC 61784 (IEC/TR 62453-51-60:2017)
Ta slovenski standard je istoveten z: CLC/TR 62453-51-60:2019
ICS:
25.040.40 Merjenje in krmiljenje Industrial process
industrijskih postopkov measurement and control
35.240.50 Uporabniške rešitve IT v IT applications in industry
industriji
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
TECHNICAL REPORT CLC/TR 62453-51-60
RAPPORT TECHNIQUE
TECHNISCHER BERICHT
February 2019
ICS 25.040.40; 35.110
English Version
Field device tool (FDT) interface specification - Part 51-60:
Communication implementation for common object model - IEC
61784 CPF 6
(IEC/TR 62453-51-60:2017)
Spécification des interfaces des outils des dispositifs de Field Device Tool (FDT)-Schnittstellenspezifikation - Teil
terrain (FDT) - Partie 51-60: Mise en œuvre d'un profil de 51-60: Kommunikationsimplementierung mit dem
communication pour le modèle d'objet commun - CPF 6 de allgemeinen Objektmodell (COM) -
l'IEC 61784 Kommunikationsprofilfamilie (CPF) 6 nach IEC 6178
(IEC/TR 62453-51-60:2017) (IEC/TR 62453-51-60:2017)
This Technical Report was approved by CENELEC on 2019-01-07.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden,
Switzerland, Turkey and the United Kingdom.
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2019 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. CLC/TR 62453-51-60:2019 E
European foreword
This document (CLC/TR 62453-51-60:2019) consists of the text of the IEC/TR 62453-51-60:2017
prepared by IEC/TC 65 "Industrial-process measurement, control and automation".
Endorsement notice
The text of the International Standard IEC TR 62453-51-60:2017 was approved by CENELEC as a
European Standard without any modification.
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments)
applies.
NOTE 1 When an International Publication has been modified by common modifications, indicated by (mod), the relevant
EN/HD applies.
NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is available here:
www.cenelec.eu.
Publication Year Title EN/HD Year
IEC 61784-1 2014 Industrial communication networks - EN 61784-1 2014
Profiles - Part 1: Fieldbus profiles
IEC 62453-1 2016 Field device tool (FDT) interface EN 62453-1 2017
specification - Part 1: Overview and
guidance
IEC TR 62453-41 2016 Field device tool (FDT) interface - -
specification - Part 41: Object model
integration profile - Common object mode
IEC 62453-2 2016 Field device tool (FDT) interface EN 62453-2 2017
specification - Part 2: Concepts and
detailed description
IEC 62453-306 2009 Field device tool (FDT) interface EN 62453-306 2009
specification - Part 306: Communication
profile integration - IEC 61784 CPF 6
IEC TR 62453-51-60 ®
Edition 1.0 2017-06
TECHNICAL
REPORT
colour
inside
Field device tool (FDT) interface specification –
Part 51-60: Communication implementation for common object model –
IEC 61784 CPF 6
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
ICS 25.040.40; 35.110.05; 35.110 ISBN 978-2-8322-4327-5
– 2 – IEC TR 62453-51-60:2017 © IEC 2017
CONTENTS
FOREWORD . 3
INTRODUCTION . 5
1 Scope . 6
2 Normative references . 6
3 Terms, definitions, symbols, abbreviated terms and conventions . 6
3.1 Terms and definitions . 6
3.2 Symbols and abbreviated terms . 7
3.3 Conventions . 7
3.3.1 Data type names and references to data types . 7
3.3.2 Vocabulary for requirements . 7
4 Bus category . 7
5 Access to instance and device data . 7
6 Protocol specific behavior . 8
7 Protocol specific usage of general data types . 8
8 Network management data types . 8
8.1 General . 8
8.2 Interbus Device Address . 8
9 Communication data types – FDTInterbusPCPCommunicationSchema . 9
10 Channel parameter data types – FDTInterbusChannelParameterSchema . 11
11 Device identification . 12
11.1 Device type identification data types – FDTInterbusIdentSchema. 12
11.2 Topology scan data types – DTMInterbusDeviceSchema . 13
11.3 Scan identification data types – FDTInterbusScanIdentSchema . 14
11.4 Device type identification data types – FDTInterbusDeviceIdentSchema . 16
11.5 XSLT Transformation . 17
Bibliography . 26
Figure 1 – Part 51-60 of the IEC 62453 series . 5
Table 1 – Protocol specific usage of general data types . 8
IEC TR 62453-51-60:2017 © IEC 2017 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
FIELD DEVICE TOOL (FDT) INTERFACE SPECIFICATION –
Part 51-60: Communication implementation for common object model –
IEC 61784 CPF 6
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
The main task of IEC technical committees is to prepare International Standards. However, a
technical committee may propose the publication of a technical report when it has collected
data of a different kind from that which is normally published as an International Standard, for
example "state of the art".
IEC TR 62453-51-60, which is a technical report, has been prepared by subcommittee 65E:
Devices and integration in enterprise systems, of IEC technical committee 65: Industrial-
process management, control and automation.
This document cancels and replaces IEC TR 62453-506 published in 2009. This edition
constitutes a technical revision. The main changes consist in updates of the schemas.
Each part of the IEC 62453-51-xy series is intended to be read in conjunction with its
corresponding part in the IEC 62453-3xy series. This document corresponds to
IEC 62453-306.
– 4 – IEC TR 62453-51-60:2017 © IEC 2017
The text of this technical report is based on the following documents:
Enquiry draft Report on voting
65E/440/DTR 65E/514/RVC
Full information on the voting for the approval of this technical report can be found in the
report on voting indicated in the above table.
This document has been drafted in accordance with the ISO/IEC Directives, Part 2.
The list of all parts of the IEC 62453 series, under the general title Field device tool (FDT)
interface specification, can be found on the IEC website.
The committee has decided that the contents of this document will remain unchanged until the
stability date indicated on the IEC website under "http://webstore.iec.ch" in the data related to
the specific document. At this date, the document will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.
A bilingual version of this publication may be issued at a later date.
IMPORTANT – The 'colour inside' logo on the cover page of this publication indicates
that it contains colours which are considered to be useful for the correct
unders
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.