Ferrite cores - Guidelines on dimensions and the limits of surface irregularities - Part 12: Ring-cores

This part of IEC 63093 specifies the dimensions that are of importance for mechanical interchangeability for a preferred range of ring-cores, also called toroid cores, and the effective parameter values to be used in calculations involving them. It also gives guidelines on allowable limits of surface irregularities applicable to ring-cores. This document is a specification useful in the negotiations between ferrite core manufacturers and users about surface irregularities.

Ferritkerne - Richtlinien zu Maßen und Grenzen von Oberflächenbeschädigungen - Teil 12: Ringkerne

Noyaux ferrites - Lignes directrices relatives aux dimensions et aux limites des irrégularités de surface - Partie 12: Noyaux toriques

La présente partie de l’IEC 63093 spécifie les dimensions importantes pour l’interchangeabilité matérielle d’une gamme préférentielle de noyaux toriques, et les valeurs des paramètres effectifs à utiliser dans les calculs les impliquant. Elle donne également des lignes directrices relatives aux limites admises des irrégularités de surface applicables aux noyaux toriques. Le présent document est une spécification utile dans les négociations entre les fabricants et les clients de noyaux ferrites au sujet des irrégularités de surface.

Feritna jedra - Smernice o merah in mejnih vrednostih površinskih nepravilnosti - 12. del: Obročasta jedra

Ta del standarda IEC 63093 določa mere, ki so pomembne za mehansko medsebojno zamenljivost prednostnega razpona obročastih jeder, imenovanih tudi toroidna jedra, in dejanske vrednosti parametrov, ki se uporabljajo pri izračunih, povezanih s temi jedri. Podaja tudi smernice glede omejitev površinskih nepravilnosti, ki veljajo za obročasta jedra.
Ta dokument je specifikacija, uporabna za sklepanje dogovorov o površinskih nepravilnostih med proizvajalci in uporabniki feritnih jeder.

General Information

Status
Published
Publication Date
20-Jun-2019
Withdrawal Date
08-May-2022
Current Stage
6060 - Document made available - Publishing
Start Date
21-Jun-2019
Completion Date
21-Jun-2019

Relations

Buy Standard

Standard
EN IEC 63093-12:2019
English language
21 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


SLOVENSKI STANDARD
01-september-2019
Feritna jedra - Smernice o merah in mejnih vrednostih površinskih nepravilnosti -
12. del: Obročasta jedra
Ferrite cores - Guidelines on dimensions and the limits of surface irregularities - Part 12:
Ring-cores
Ta slovenski standard je istoveten z: EN IEC 63093-12:2019
ICS:
29.100.10 Magnetne komponente Magnetic components
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD EN IEC 63093-12

NORME EUROPÉENNE
EUROPÄISCHE NORM
June 2019
ICS 29.100.10 Supersedes EN 62317-12:2016
EN 60424-4:2016
English Version
Ferrite cores - Guidelines on dimensions and the limits of
surface irregularities - Part 12: Ring-cores
(IEC 63093-12:2019)
Noyaux ferrites - Lignes directrices relatives aux Ferritkerne - Richtlinien zu Maßen und Grenzen von
dimensions et aux limites des irrégularités de surface - Oberflächenbeschädigungen - Teil 12: Ringkerne
Partie 12: Noyaux toriques (IEC 63093-12:2019)
(IEC 63093-12:2019)
This European Standard was approved by CENELEC on 2019-05-09. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden,
Switzerland, Turkey and the United Kingdom.

European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2019 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN IEC 63093-12:2019 E

European foreword
The text of document 51/1271/FDIS, future edition 1 of IEC 63093-12, prepared by IEC/TC 51
"Magnetic components, ferrite and magnetic powder materials" was submitted to the IEC-CENELEC
parallel vote and approved by CENELEC as EN IEC 63093-12:2019.
The following dates are fixed:
• latest date by which the document has to be implemented at national (dop) 2020-02-09
level by publication of an identical national standard or by endorsement
• latest date by which the national standards conflicting with the (dow) 2022-05-09
document have to be withdrawn
This document supersedes EN 62317-12:2016 and EN 60424-4:2016
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.

Endorsement notice
The text of the International Standard IEC 63093-12:2019 was approved by CENELEC as a European
Standard without any modification.
In the official version, for Bibliography, the following notes have to be added for the standards
indicated:
IEC 60401-2 NOTE Harmonized as EN 60401-2
IEC 60424-4 NOTE Harmonized as EN 60424-4
IEC 62317-1 NOTE Harmonized as EN 62317-1

Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments)
applies.
NOTE 1  Where an International Publication has been modified by common modifications, indicated by (mod), the relevant
EN/HD applies.
NOTE 2  Up-to-date information on the latest versions of the European Standards listed in this annex is available here:
www.cenelec.eu.
Publication Year Title EN/HD Year
IEC 60205 -  Calculation of the effective parameters of EN 60205 -
magnetic piece parts
IEC 60401-1 -  Terms and nomenclature for cores made of EN 60401-1 -
magnetically soft ferrites - Part 1: Terms used for
physical irregularities
IEC 60424-1 -  Ferrite cores - Guidelines on the limits of surface EN 60424-1 -
irregularities - Part 1: General specification

IEC 63093-12 ®
Edition 1.0 2019-04
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Ferrite cores – Guidelines on dimensions and the limits of surface irregularities –

Part 12: Ring-cores
Noyaux ferrites – Lignes directrices relatives aux dimensions et aux limites des

irrégularités de surface –
Partie 12: Noyaux toriques
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 29.100.10 ISBN 978-2-8322-6715-8

– 2 – IEC 63093-12:2019 © IEC 2019
CONTENTS
FOREWORD . 3
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 5
4 Primary dimensions . 5
4.1 General . 5
4.2 Dimensions of ring-cores . 6
4.2.1 Designation of dimensions . 6
4.2.2 Identification of standard sizes . 6
4.2.3 Effective parameter values. 6
4.2.4 Dimensional limits for standard sizes . 7
4.3 Coating . 13
5 Limits of surface irregularities . 13
5.1 Uncoated ring-cores . 13
5.1.1 General. 13
5.1.2 Chips and ragged edges . 13
5.1.3 Cracks and pull-outs . 14
5.1.4 Crystallites . 14
5.1.5 Pores . 15
5.2 Coated ring-cores . 15
5.2.1 General. 15
5.2.2 Coating features . 15
5.2.3 Coating performance . 16
5.3 Area and length reference for visual inspection . 16
Bibliography . 18

Figure 1 – Dimensions of ring-cores . 6
Figure 2 – Location of chips and ragged edges on ring-cores . 14
Figure 3 – Location of cracks and pull-out on ring-cores . 14
Figure 4 – Location of crystallite on ring-cores . 15
Figure 5 – Location of pore on ring-cores . 15

Table 1 – Ring-core dimension designations . 6
Table 2 – Standard ring-cores . 7
Table 3 – Effective parameters of ring-cores . 9
Table 4 – Recommended dimensional limits for uncoated ring-cores . 11
Table 5 – Area and length reference for visual inspection . 17

IEC 63093-12:2019 © IEC 2019 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
FERRITE CORES – GUIDELINES ON DIMENSIONS
AND THE LIMITS OF SURFACE IRREGULARITIES –

Part 12: Ring-cores
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 63093-12 has been prepared by IEC technical committee 51:
Magnetic components, ferrite and magnetic powder materials.
This first edition cancels and replaces the first edition of IEC 62317-12 published in 2016 and
the second edition of IEC 60424-4 published in 2015. This edition constitutes a technical
revision.
This edition includes the following significant technical changes with respect to IEC 62317-
12:2016 and IEC 60424-4:2015:
a) IEC 63093-12 integrates the contents of IEC 62317
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.