EN 61788-4:2001
(Main)Superconductivity - Part 4: Residual resistance ratio measurement - Residual resistance ratio of Nb-Ti composite superconductors
Superconductivity - Part 4: Residual resistance ratio measurement - Residual resistance ratio of Nb-Ti composite superconductors
Describes a reference method for the determination of the residual resistance ratio (RRR) of a composite superconductor comprised of Nb-Ti filaments and Cu, Cu-Ni or Cu/Cu-Ni matrix. This method is intended for use with superconductors that have a rectangular or round cross-section, RRR less than 350, and cross-sectional area less than 3 mm2. All measurements shall be done without an applied magnetic field. Optional acquisition methods are outlined in annex A.
Supraleitfähigkeit - Teil 4: Messungen des Restwiderstandsverhältnisses - Restwiderstandsverhältnis von Nb-Ti-Verbundsupraleitern
Supraconductivité - Partie 4: Mesure de la résistivité résiduelle - Taux de résistivité résiduelle des supraconducteurs composites au Nb-Ti
Superconductivity - Part 4: Residual resistance ratio measurement - Residual resistance ratio of Nb-Ti composite superconductors
General Information
Relations
This May Also Interest You
IEC 61788-17:2021 is available as IEC 61788-17:2021 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.IEC 61788-17:2021 specifies the measurements of the local critical current density (Jc) and its distribution in large-area high-temperature superconducting (HTS) films by an inductive method using third-harmonic voltages. The most important consideration for precise measurements is to determine Jc at liquid nitrogen temperatures by an electric-field criterion and obtain current-voltage characteristics from its frequency dependence. Although it is possible to measure Jc in applied DC magnetic fields [20] [21], the scope of this document is limited to the measurement without DC magnetic fields. This technique intrinsically measures the critical sheet current that is the product of Jc and the film thickness d. The range and measurement resolution for Jcd of HTS films are as follows. - Jcd: from 200 A/m to 32 kA/m (based on results, not limitation). - Measurement resolution: 100 A/m (based on results, not limitation).
- Standard44 pagesEnglish languagesale 10% offe-Library read for×1 day
IEC 61788-26:2020 specifies a test method for determining the DC critical current of short RE (rare earth)-Ba-Cu-O (REBCO) composite superconductor specimens that have a shape of straight flat tape. This document applies to test specimens shorter than 300 mm and having a rectangular cross section with an area of 0,03 mm2 to 7,2 mm2, which corresponds to tapes with width ranging from 1,0 mm to 12,0 mm and thickness from 0,03 mm to 0,6 mm. This method is intended for use with superconductor specimens that have critical current less than 300 A and n-values larger than 5 under standard test conditions: the test specimen is immersed in liquid nitrogen bath at ambient pressure without external magnetic field during the testing. Deviations from this test method that are allowed for routine tests and other specific restrictions are given in this document.
- Standard30 pagesEnglish languagesale 10% offe-Library read for×1 day
IEC 61788-4:2020 is available as IEC 61788-4:2020 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.IEC 61788-4:2020 specifies a test method for the determination of the residual resistance ratio (RRR) of Nb-Ti and Nb3Sn composite superconductors with Cu, Cu-Ni, Cu/Cu-Ni and Al matrix in a strain-free condition and zero external magnetic field. This method is intended for use with superconductor specimens that have a monolithic structure with rectangular or round cross-section, RRR value less than 350, and cross-sectional area less than 3 mm2. In the case of Nb3Sn, the specimens have received a reaction heat-treatment. This fifth edition cancels and replaces the fourth edition published in 2016. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: a) change in the suitable distance of voltage taps on the specimen for reliable measurement, b) new report on the result of the round robin test of the residual resistance ratio of Nb3Sn superconductors that proves the validity of the measurement method in this standard, c) revision of the confusing definitions of the copper ratio and copper fraction.
- Standard37 pagesEnglish languagesale 10% offe-Library read for×1 day
IEC 61788-7:2020 is available as IEC 61788-7:2020 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.IEC 61788-7:2020 describes measurement of the surface resistance (Rs) of superconductors at microwave frequencies by the standard two-resonator method. The object of measurement is the temperature dependence of Rs at the resonant frequency. The applicable measurement range of Rs for this method is as follows: - Frequency: 8 GHz < f < 30 GHz - Measurement resolution: 0,01 m Ω at 10 GHz The Rs data at the measured frequency, and that scaled to 10 GHz, assuming the f 2 rule for comparison, is reported. This third edition cancels and replaces the second edition, published in 2006. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: a) informative Annex B, relative combined standard uncertainty for surface resistance measurement has been added; b) precision and accuracy statements have been converted to uncertainty; c) reproducibility in surface resistant measurement has been added.
- Standard46 pagesEnglish languagesale 10% offe-Library read for×1 day
IEC 61788-5:2013 covers a test method for the determination of copper to superconductor volume ratio of Cu/Nb-Ti composite superconducting wires. This test method and the alternate method in Annex are intended for use with Cu/Nb-Ti composite superconducting wires with a cross-sectional area of 0,1 mm2 to 3 mm2, a diameter of the Nb-Ti filament(s) of 2 micrometers to 200 micrometers, and a copper to superconductor volume ratio of 0,5 or more. The Cu/Nb-Ti composite test conductor discussed in this method has a monolithic structure with a round or rectangular cross-section. This test method is carried out by dissolving the copper with nitric acid. Deviations from this test method that are allowed for routine tests and other specific restrictions are given in this standard. Cu/Nb-Ti composite superconducting wires beyond the limits in the cross-sectional area, the filament diameter and the copper to superconductor volume ratio could be measured with this present method with an anticipated reduction of uncertainty. Other, more specialized, specimen test geometries may be more appropriate for conductors beyond the limits and have been omitted from this present standard for simplicity and to retain low uncertainty. The test method given in this standard is expected to apply to other superconducting composite wires after some appropriate modifications. The copper to superconductor volume ratio of composite superconductors is used mainly to calculate the critical current density of superconducting wires. The test with the method given in this International Standard may be used to provide part of the information needed to determine the suitability of a specific superconductor. Moreover, this method is useful for quality control, acceptance or research testing if the precautions given in this standard are observed. This second edition cancels and replaces the first edition published in 2000. It constitutes a technical revision. The main revisions are the addition of two new annexes, 'Uncertainty considerations' (Annex E) and 'Uncertainty evaluation in test method of copper to superconductor volume ratio of Cu/Nb-Ti composite superconductors' (Annex F).
- Standard28 pagesEnglish languagesale 10% offe-Library read for×1 day
IEC 61788-16:2013 involves describing the standard measurement method of power-dependent surface resistance of superconductors at microwave frequencies by the sapphire resonator method. The measuring item is the power dependence of Rs at the resonant frequency. This method is the applicable for a frequency in the range of 10 GHz, for an input microwave power lower than 37 dBm (5 W). The aim is to report the surface resistance data at the measured frequency and that scaled to 10 GHz. Keyword: superconductivity
- Standard33 pagesEnglish languagesale 10% offe-Library read for×1 day
IEC 61788-17:2021 is available as IEC 61788-17:2021 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.IEC 61788-17:2021 specifies the measurements of the local critical current density (Jc) and its distribution in large-area high-temperature superconducting (HTS) films by an inductive method using third-harmonic voltages. The most important consideration for precise measurements is to determine Jc at liquid nitrogen temperatures by an electric-field criterion and obtain current-voltage characteristics from its frequency dependence. Although it is possible to measure Jc in applied DC magnetic fields [20] [21], the scope of this document is limited to the measurement without DC magnetic fields. This technique intrinsically measures the critical sheet current that is the product of Jc and the film thickness d. The range and measurement resolution for Jcd of HTS films are as follows. - Jcd: from 200 A/m to 32 kA/m (based on results, not limitation). - Measurement resolution: 100 A/m (based on results, not limitation).
- Standard44 pagesEnglish languagesale 10% offe-Library read for×1 day
IEC 61788-26:2020 specifies a test method for determining the DC critical current of short RE (rare earth)-Ba-Cu-O (REBCO) composite superconductor specimens that have a shape of straight flat tape. This document applies to test specimens shorter than 300 mm and having a rectangular cross section with an area of 0,03 mm2 to 7,2 mm2, which corresponds to tapes with width ranging from 1,0 mm to 12,0 mm and thickness from 0,03 mm to 0,6 mm. This method is intended for use with superconductor specimens that have critical current less than 300 A and n-values larger than 5 under standard test conditions: the test specimen is immersed in liquid nitrogen bath at ambient pressure without external magnetic field during the testing. Deviations from this test method that are allowed for routine tests and other specific restrictions are given in this document.
- Standard30 pagesEnglish languagesale 10% offe-Library read for×1 day
IEC 61788-7:2020 is available as IEC 61788-7:2020 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.IEC 61788-7:2020 describes measurement of the surface resistance (Rs) of superconductors at microwave frequencies by the standard two-resonator method. The object of measurement is the temperature dependence of Rs at the resonant frequency. The applicable measurement range of Rs for this method is as follows: - Frequency: 8 GHz < f < 30 GHz - Measurement resolution: 0,01 m Ω at 10 GHz The Rs data at the measured frequency, and that scaled to 10 GHz, assuming the f 2 rule for comparison, is reported. This third edition cancels and replaces the second edition, published in 2006. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: a) informative Annex B, relative combined standard uncertainty for surface resistance measurement has been added; b) precision and accuracy statements have been converted to uncertainty; c) reproducibility in surface resistant measurement has been added.
- Standard46 pagesEnglish languagesale 10% offe-Library read for×1 day
IEC 61788-4:2020 is available as IEC 61788-4:2020 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.IEC 61788-4:2020 specifies a test method for the determination of the residual resistance ratio (RRR) of Nb-Ti and Nb3Sn composite superconductors with Cu, Cu-Ni, Cu/Cu-Ni and Al matrix in a strain-free condition and zero external magnetic field. This method is intended for use with superconductor specimens that have a monolithic structure with rectangular or round cross-section, RRR value less than 350, and cross-sectional area less than 3 mm2. In the case of Nb3Sn, the specimens have received a reaction heat-treatment. This fifth edition cancels and replaces the fourth edition published in 2016. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: a) change in the suitable distance of voltage taps on the specimen for reliable measurement, b) new report on the result of the round robin test of the residual resistance ratio of Nb3Sn superconductors that proves the validity of the measurement method in this standard, c) revision of the confusing definitions of the copper ratio and copper fraction.
- Standard37 pagesEnglish languagesale 10% offe-Library read for×1 day
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.