EN 50411-3-6:2013
(Main)Fibre organisers and closures to be used in optical fibre communication systems - Product specifications - Part 3-6: Multimode mechanical fibre splice for use in an outdoor protected environment (Cat U)
Fibre organisers and closures to be used in optical fibre communication systems - Product specifications - Part 3-6: Multimode mechanical fibre splice for use in an outdoor protected environment (Cat U)
1.1 Product definition This European Standard contains the initial, start of life dimensional, optical, mechanical and environmental performance requirements which a multimode mechanical splice will meet in order for it to be categorised as an EN standard product. Since different variants and grades of performance are permitted, product marking and identification details are given in 3.5. Although in this document the product is qualified for EN 60793-2-10 type A1a.1, A1a.2, A1a.3 and A1b multimode fibres, it may also be suitable for other fibre types. 1.2 Interoperability The installed mechanical splice fits into a fibre management system with optical fibre splice cassettes or splice trays. This European Standard specifies the following two physical interface dimensions: • cross sectional profile with width, height or diameter (in millimetres); • length (in millimetres). 1.3 Expected performance In this document, the performance of a mechanical splice is given with identical fibres only. Losses associated with fibre cladding diameter and mode field mismatch are not taken into account. The measured attenuation is a function of the core concentricity, cladding non-circularity and alignment capability. The optical return loss performance is a function of the index matching gel and the fibre end face preparation. 1.4 Operating environment The tests selected combined with the severities and durations are representative of an outdoor enclosed environment defined as category U in EN 61753-1. To ensure that the product can be used in closures, boxes or street cabinet for categories A, G and S (as defined EN 61753-1) the specified lower temperature is extended to -40 °C and requirements for temporary flooding have been added. 1.5 Reliability Whilst the anticipated service life expectancy of the product in this environment is 20 years, compliance with this specification does not guarantee the reliability of the product. This should be predicted using a recognised reliability assessment programme. 1.6 Quality assurance Compliance with this specification does not guarantee the manufacturing consistency of the product. This should be maintained using a recognised quality assurance programme.
LWL-Spleißkassetten und -Muffen für die Anwendung in LWL Kommunikationssystemen - Produktnorm - Teil 3-6: Mechanische Spleiße von Mehrmoden-Faser für geschützte Freiluftanwendungen (Kategorie U)
Produktdefinition Diese Europäische Norm enthält die Anfangs- und Maßanforderungen zu Beginn der Lebensdauer sowie die optischen, mechanischen und umweltbezogenen Leistungsanforderungen, die ein mechanischer Spleiß einer Mehrmoden-Faser erfüllen wird, um als EN-Normprodukt eingestuft zu werden. Da verschiedene Varianten und Leistungsklassen zulässig sind, werden in 3.5 Einzelheiten zur Produktkenn¬zeichnung angegeben. Obwohl die nach diesem Dokument qualifizierten Produkte für Mehrmoden-Fasern des Typs A1a.1, A1a.2, A1a.3 and A1b gemäß EN 60793-2-10:2007 sind, können sie auch für andere Fasertypen geeignet sein. 1.2 Passfähigkeit Die installierten mechanischen Spleiße passen in ein Fasermanagementsystem mit LWL-Spleißkassetten oder LWL-Spleißwannen. In der vorliegenden Europäischen Norm werden die beiden folgenden physikalischen Schnitt¬stellenmaße festgelegt: – Querschnitt mit Breite, Höhe oder Durchmesser (in mm); – Länge (in mm). 1.3 Erwartetes Betriebsverhalten Das Betriebsverhalten eines mechanischen Spleißes ist nach dem vorliegenden Dokument nur bei identi-schen Fasern sichergestellt. Verluste im Zusammenhang mit einer Fehlanpassung von Fasermantel-durchmesser und Modenfelddurchmesser bleiben unberücksichtigt. Die gemessene Dämpfung ist eine Funk¬tion der Konzentrizität des Kerns, der Unrundheit des Mantels und der Ausrichtungsfähigkeit. Die optische Rückflussdämpfung ist eine Funktion des Gels mit angepasster Brechzahl und der Vorbereitung der Faser¬endflächen. 1.4 Betriebsumgebung Die ausgewählten Prüfungen in Kombination mit den Prüfschärfe und dauern sind repräsentativ für eine geschlossene Umgebung im Freien nach den Festlegungen für Kategorie U in IEC 61753 1:2007. Damit gewähr¬leistet ist, dass das Produkt in Muffen, Kästen oder Straßenschränken für die Kategorien A, G und S (nach den Festlegungen in EN 61753 1:2007) angewendet werden kann, wurde die festgelegte untere Temperatur auf –40 °C erweitert und es wurden Anforderungen für eine zeitweilige Überflutung aufgenommen. 1.5 Zuverlässigkeit Die erwartete Betriebslebensdauer des Produktes in dieser Umgebung beträgt 20 Jahre, wobei die Einhal-tung dieser Spezifikation die Zuverlässigkeit des Produktes nicht garantiert. Diese sollte mit einem aner-kannten Zuverlässigkeitsbewertungsprogramm vorhergesagt werden. 1.6 Qualitätssicherung Die Einhaltung dieser Spezifikation garantiert nicht die Beständigkeit der Herstellung des Produktes. Diese sollte mit einem anerkannten Qualitätssicherungsprogramm aufrechterhalten werden.
Organiseurs et boîtiers de fibres destinés à être utilisés dans les systèmes de communication par fibres optiques - Spécifications de produits - Partie 3-6: Epissure mécanique de fibres multimodales installée en environnement extérieur protégé (Cat U)
1.1 Définition du produit La présente norme européenne contient les exigences de performances initiales, dimensionnelles, optiques, mécaniques et environnementales, de début de vie, auxquelles une épissure mécanique multimodale satisfera, afin d'être classée comme produit conforme à une norme EN. Dans la mesure où différentes variantes et différentes classes de performances sont autorisées, les détails de marquage et d’identification des produits sont donnés en 3.5. Bien que, dans le présent document, le produit soit qualifié pour des fibres multimodales de types A1a.1, A1a.2, A1a.3 et A1b de l’EN 60793-2-10, il peut également convenir à d’autres types de fibres. 1.2 Interopérabilité Les épissures mécaniques installées s’adaptent à un système de gestion de fibres avec des cassettes ou des plateaux d'épissures de fibres optiques. La présente norme européenne spécifie les deux dimensions d’interface physique suivantes: • profil transversal avec largeur, hauteur ou diamètre (en millimètres); • longueur (en millimètres). 1.3 Performance attendue Dans le présent document, la performance d’une épissure mécanique est donnée avec des fibres identiques uniquement. Les pertes associées au diamètre de la gaine de fibre et au défaut d’adaptation du champ de mode ne sont pas prises en compte. L’affaiblissement mesuré dépend de la concentricité du cœur, de la non-circularité de la gaine et de la capacité d'alignement. La performance de l’affaiblissement de réflexion optique dépend du gel permettant de conserver l’indice et de la préparation de l'extrémité de la fibre. 1.4 Environnement de fonctionnement Les essais choisis combinés avec les sévérités et les durées sont représentatifs de l’environnement extérieur enfermé défini comme catégorie U dans l'EN 61753-1. Afin de garantir que le produit peut être utilisé dans des enveloppes, des boîtes ou des armoires pour les catégories A, G et S (telles que définies dans l'EN 61753-1), la température inférieure spécifiée est étendue à -40 °C, et des exigences relatives à une immersion temporaire ont été ajoutées. 1.5 Fiabilité Tandis que l'espérance de vie du produit en service prévue dans cet environnement est de 20 ans, la conformité à la présente spécification ne garantit pas la fiabilité du produit. Il convient que celle-ci soit estimée en utilisant un programme reconnu d'évaluation de la fiabilité. 1.6 Assurance de la qualité La conformité à la présente spécification ne garantit pas la cohérence de fabrication du produit. Il convient qu’elle soit suivie en utilisant un programme reconnu d'assurance de la qualité.
Delilniki za optična vlakna in kabelske spojnice za optične komunikacijske sisteme - Specifikacija izdelka - 3-6. del: Večrodna mehanska optična spojnica
Ta standard vsebuje začetne dimenzijske, optične, mehanske in okoljske zahteve, ki jih mora na začetku svoje življenjske dobe izpolnjevati večrodna mehanska spojnica, da se lahko kategorizira kot izdelek v skladu s standardom EN.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 50411-3-6:2013
01-april-2013
'HOLOQLNL]DRSWLþQDYODNQDLQNDEHOVNHVSRMQLFH]DRSWLþQHNRPXQLNDFLMVNHVLVWHPH
6SHFLILNDFLMDL]GHONDGHO9HþURGQDPHKDQVNDRSWLþQDVSRMQLFD
Fibre organisers and closures to be used in optical fibre communication systems -
Product specifications - Part 3-6: Multimode mechanical fibre splice
LWL-Spleißkassetten und -Muffen für die Anwendung in LWL Kommunikationssystemen
- Produktnorm - Teil 3-6: Mechanische Spleiße für Mehrmoden-Fasern
Organiseurs et boîtiers de fibres destinés à être utilisés dans les systèmes de
communication par fibres optiques - Spécifications de produits -- Part 3-6: Epissure
mécanique de fibres multimodales
Ta slovenski standard je istoveten z: EN 50411-3-6:2013
ICS:
33.180.20 3RYH]RYDOQHQDSUDYH]D Fibre optic interconnecting
RSWLþQDYODNQD devices
SIST EN 50411-3-6:2013 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 50411-3-6:2013
---------------------- Page: 2 ----------------------
SIST EN 50411-3-6:2013
EUROPEAN STANDARD
EN 50411-3-6
NORME EUROPÉENNE
March 2013
EUROPÄISCHE NORM
ICS 33.180.20
English version
Fibre organisers and closures to be used in optical fibre communication
systems -
Product specifications -
Part 3-6: Multimode mechanical fibre splice for use in an outdoor
protected environment (Cat U)
Organiseurs et boîtiers de fibres destinés LWL-Spleißkassetten und -Muffen für die
à être utilisés dans les systèmes de Anwendung in LWL
communication par fibres optiques - Kommunikationssystemen -
Spécifications de produits - Produktnorm -
Partie 3-6: Epissure mécanique de fibres Teil 3-6: Mechanische Spleiße von
multimodales installée en environnement Mehrmoden-Faser für geschützte
extérieur protégé (Cat U) Freiluftanwendungen (Kategorie U)
This European Standard was approved by CENELEC on 2012-12-24. CENELEC members are bound to comply
with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard
the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the CEN-CENELEC Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and notified
to the CEN-CENELEC Management Centre has the same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus,
the Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany,
Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.
CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
Management Centre: Avenue Marnix 17, B - 1000 Brussels
© 2013 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 50411-3-6:2013 E
---------------------- Page: 3 ----------------------
SIST EN 50411-3-6:2013
EN 50411-3-6:2013 – 2 –
Contents
Foreword . 3
1 Scope . 5
1.1 Product definition . 5
1.2 Interoperability . 5
1.3 Expected performance . 5
1.4 Operating environment . 5
1.5 Reliability . 5
1.6 Quality assurance . 5
2 Normative references . 5
3 Description .
...
SLOVENSKI STANDARD
oSIST prEN 50411-3-6:2011
01-februar-2011
'HOLOQLNL]DRSWLþQDYODNQDLQNDEHOVNHVSRMQLFH]DRSWLþQHNRPXQLNDFLMVNHVLVWHPH
6SHFLILNDFLMDL]GHONDGHO9HþURGQDPHKDQVNDRSWLþQDVSRMQLFD
Fibre organisers and closures to be used in optical fibre communication systems -
Product specifications - Part 3-6: Multimode mechanical fibre splice
Ta slovenski standard je istoveten z: prEN 50411-3-6:2010
ICS:
33.180.20 3RYH]RYDOQHQDSUDYH]D Fibre optic interconnecting
RSWLþQDYODNQD devices
oSIST prEN 50411-3-6:2011 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
oSIST prEN 50411-3-6:2011
---------------------- Page: 2 ----------------------
oSIST prEN 50411-3-6:2011
DRAFT
EUROPEAN STANDARD
prEN 50411-3-6
NORME EUROPÉENNE
December 2010
EUROPÄISCHE NORM
ICS
English version
Fibre organisers and closures to be used
in optical fibre communication systems -
Product specifications -
Part 3-6: Multimode mechanical fibre splice
To be completed To be completed
This draft European Standard is submitted to CENELEC members for CENELEC enquiry.
Deadline for CENELEC: 2011-05-20.
It has been drawn up by CLC/TC 86BXA.
If this draft becomes a European Standard, CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national
standard without any alteration.
This draft European Standard was established by CENELEC in three official versions (English, French, German).
A version in any other language made by translation under the responsibility of a CENELEC member into its own
language and notified to the Central Secretariat has the same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus,
the Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy,
Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia,
Spain, Sweden, Switzerland and the United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of
which they are aware and to provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to
change without notice and shall not be referred to as a European Standard.
CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
Management Centre: Avenue Marnix 17, B - 1000 Brussels
© 2010 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Project: 22858 Ref. No. prEN 50411-3-6:2010 E
---------------------- Page: 3 ----------------------
oSIST prEN 50411-3-6:2011
prEN 50411-3-6:2010 – 2 –
1 Foreword
2 This draft European Standard was prepared by the Technical Committee CENELEC TC 86BXA, Fibre optic
3 interconnect, passive and connectorised components. It is submitted to the CENELEC enquiry.
4 __________
---------------------- Page: 4 ----------------------
oSIST prEN 50411-3-6:2011
– 3 – prEN 50411-3-6:2010
Fibre organisers and closures to be used in optical fibre communication systems –
Product specifications
Part 3-6: Multimode mechanical fibre splice
Description Performance
Type: Fibre splice Application: EN 61753-1:2007, Category U
with extension of lower
Style: Mechanical
temperature to -40 °C
Operating wavelength: 850 nm and 1 300 nm Attenuation grades ≤ 0,25 dB maximum (97 %)
Fibre category EN 60793-2-10:2007, type Return loss grades
≥ 20 dB
A1a.1, A1a.2, A1a.3 and
A1b
Related documents:
EN 60793-2-10:2007 Optical fibres – Part 2-10: Product specifications – Sectional specification for category
A1 multimode fibres (IEC 60793-2-10:2007)
EN 60794-2-50 Optical fibre cables – Part 2-50: Indoor cables – Family specification for simplex
and duplex cables for use in terminated cable assemblies (IEC 60794-2-50)
EN 61300 series Fibre optic interconnecting devices and passive components – Basic test and
measurement procedures (IEC 61300 series)
Fibre optic interconnecting devices and passive components performance
EN 61753-1:2007
standard – Part 1: General and guidance for performance standards
(IEC 61753-1:2007)
Outline and maximum dimensions:
Variant Dimension Dimension Dimension
W H L
mm mm mm
L
Type M1 3,8 6,4 38
H
4,0 4,0 36
Type M2
W
Type M3 3,2 3,2 45
Type M4 4,2 4,2 44
4,0 4,0 40
Type M5
Type M6 Ø 5,0 65
---------------------- Page: 5 ----------------------
oSIST prEN 50411-3-6:2011
prEN 50411-3-6:2010 – 4 –
5 Contents
6 1 S
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.