Live working - Portable equipment for earthing or earthing and short-circuiting

Superseded by EN 61230:2008

Arbeiten unter Spannung - Örtsveränderliche Geräte zum Erden oder Erden und Kurzschließen

Travaux sous tension - Dispositifs portables de mise à la terre ou de mise à la terre et en court-circuit

Delo pod napetostjo - Prenosna oprema za ozemljitev ali ozemljitev in kratki stik

General Information

Status

Withdrawn

Publication Date

24-Nov-1999

Withdrawal Date

30-Sep-2002

ICS

13.260 - Protection against electric shock. Live working

Technical Committee

CLC/TC 78 - Equipment and tools for live working

Drafting Committee

IEC/TC 78 - IEC_TC_78

Parallel Committee

IEC/TC 78 - IEC_TC_78

Current Stage

9960 - Withdrawal effective - Withdrawal

Start Date

01-Oct-2011

Completion Date

01-Oct-2011

Directive

2006/95/EC - Directive 2006/95/EC of the European Parliament and of the Council of 12 December 2006 on the harmonisation of the laws of Member States relating to electrical equipment designed for use within certain voltage limits (codified version)

73/23/EEC - Electrical equipment designed for use within certain voltage limits

Ref Project

SIST EN 61230:2000/A11:2000 - Live working - Portable equipment for earthing or earthing and short-circuiting

Relations

Replaced By

EN 61230:2008 - Live working - Portable equipment for earthing or earthing and short-circuiting

Effective Date

29-Jan-2023

Amends

EN 61230:1995 - Live working - Portable equipment for earthing or earthing and short-circuiting

Effective Date

29-Jan-2023

Buy Standard

Amendment

EN 61230:2000/A11:2000

English language

2 pages

sale 10% off

Preview

sale 10% off

Preview

e-Library read for

1 day

Create e-Library subscription and get permanent access to the document. Subscriptions are available for: 13 13.260

Standards Content (Sample)

EN 61230:2000/A11:2000

SLOVENSKI STANDARD
01-junij-2000
Delo pod napetostjo - Prenosna oprema za ozemljitev ali ozemljitev in kratki stik
Live working - Portable equipment for earthing or earthing and short-circuiting
Arbeiten unter Spannung - Örtsveränderliche Geräte zum Erden oder Erden und
Kurzschließen
Travaux sous tension - Dispositifs portables de mise à la terre ou de mise à la terre et en
court-circuit
Ta slovenski standard je istoveten z: EN 6
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CLC

EN 50528:2024(Main)

Insulating ladders for use on or near low voltage electrical installations

SIST EN 50528:2024

This document is applicable to portable ladders made only of non-conductive stiles, including accessories (pole leaning device, adjustable levelling device, adjustable ladder stabilizer, etc.) used to work on or near electrical systems and installations in the low voltage range (up to 1 000 V AC/1 500 V DC). These ladders are used to provide temporary access, generally on overhead line structures, and to undertake electrical operations. They are expected to be used by one person only. These ladders, in conjunction with other protective equipment provide sufficient insulation level to protect against inadvertent contact with live low voltage installations. This document does not cover ladders used for live working on electrical installations at voltages above 1 000 V AC and above 1 500 V DC. These insulating ladders are separately covered by EN 61478. This document does not cover products not made entirely with non-conductive stiles generally called mixed ladders. In this case the EN 131 series apply. This document does not cover step stools, which are covered by EN 14183. These ladders are only for specific professional use. Only skilled persons, after an appropriate training, can use this type of ladder for professional applications. The products designed and manufactured according to this document contribute to the safety of the users provided they are used by skilled persons, in accordance with safe methods of work and the manufacturer instructions for use (where appropriate). Annex E gives a rationale to explain how a ladder which fulfils the requirements of this document used with correct accessories gives better safety for the user than an ordinary ladder.

Standard
68 pages
English language
sale 10% off
e-Library read for
1 day

23-May-2024
13.260
97.145
CLC/TC 78

CLC

EN IEC 62819:2023/AC:2024-03(Corrigendum)

Live working - Eye, face and head protectors against the effects of electric arc - Performance requirements and test methods

SIST EN IEC 62819:2023/AC:2024

Corrigendum
3 pages
English language
sale 10% off
e-Library read for
1 day

CLC

EN 50365:2023(Main)

Live Working - Electrically insulating helmets for use on low and medium voltage installations

SIST EN 50365:2024

This standard is applicable to electrically insulating helmets used for working live or close to live parts on installations not exceeding 1 000 V AC or 1 500 V DC. These helmets, when used in conjunction with other electrically insulating protective equipment prevent dangerous current from passing through persons via their head.

Standard
24 pages
English language
sale 10% off
e-Library read for
1 day

CLC

EN IEC 62819:2023(Main)

Live working - Eye, face and head protectors against the effects of electric arc - Performance requirements and test methods

SIST EN IEC 62819:2023

This document is applicable to eye, face and head protectors used in work where there is a risk of exposure to an electric arc hazard. Such protectors consist of one or several devices (e.g. hood, goggles, balaclavas, face shields, helmets, etc.), which might need to be combined together in order to give protection to eye, face and head for the intended use. This document covers the performance requirements for protectors and single protective devices considering thermal, optical and mechanical hazards of an electric arc. Because of the limitations of test apparatus at very high energy arcs, no arc rating above 4 100 kJ/m2 (100 cal/cm2) can be assigned to protectors. This document does not cover protection against electric shock, noise, the consequences of physical and mental shock and the toxic influences caused by an electric arc. This document does not cover protectors for work intentionally using an electric arc, e.g. arc welding, plasma torch. This document does not cover face-screens for the reduction of an electric field inside conductive clothing in accordance with IEC 60895. Any other claims of the manufacturer for protection against other hazards to eye or face (e.g. welding radiation, hazards occurring during fire-fighting) are outside the scope of the document. Products designed and manufactured in accordance with this document contribute to the safety of the users provided they are used by skilled persons, in accordance with safe methods of work and the instructions for use.

Standard
52 pages
English language
sale 10% off
e-Library read for
1 day

CLC

EN IEC 61318:2021(Main)

Live working - Methods for assessment of defects and verification of performance applicable to tools, devices and equipment

SIST EN IEC 61318:2021

This document defines methods to assess defects and to verify that products after the manufacturer process meet the requirements of the corresponding product standard. The principles of assessment of defects for live working products are detailed in this document to assist product standard developers in prescribing the best means to achieve suitable quality of every finished tool, device and piece of equipment. The following elements are not covered by the present document, but are included in each product standard: - type tests; - provisions and description for routine, sampling and acceptance tests; - identification and classification of defects; - risk analysis. This document does not cover conformity assessment of commercial shipments or certifications.

Standard
18 pages
English language
sale 10% off
e-Library read for
1 day

CLC

EN IEC 61243-1:2021(Main)

Live working - Voltage detectors - Part 1: Capacitive type to be used for voltages exceeding 1 kV AC

SIST EN IEC 61243-1:2021

IEC 61243-1:2021 is applicable to portable voltage detectors, with or without built-in power sources, to be used on electrical systems for voltages of 1 kV to 800 kV AC, and frequencies of 50 Hz and/or 60 Hz. This document applies only to voltage detectors of capacitive type used in contact with the bare part to be tested, as a complete device including its insulating element or as a separate device, adaptable to an insulating stick which, as a separate tool, is not covered by this document (see 4.4.2.1 for general design). Other types of voltage detectors are not covered by this document. Self ranging voltage detectors (formally "multi range voltage detectors") are not covered by this document. Some restrictions or formal interdictions on their use are applicable in case of switchgear of IEC 62271 series design, due to insulation coordination, on overhead line systems of electrified railways (see Annex B) and systems without neutral reference. For systems without neutral reference, the insulating level is adapted to the maximum possible voltage to the earth (ground). Products designed and manufactured according to this document contribute to the safety of users provided they are used by persons trained for the work, in accordance with the hot stick working method and the instructions for use. Except where otherwise specified, all the voltages defined in this document refer to values of phase-to-phase voltages of three-phase systems. In other systems, the applicable phase-to-phase or phase-to-earth (ground) voltages are used to determine the operating voltage. This third edition cancels and replaces the second edition published in 2003 and Amend-ment 1:2009. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: a) The scope is more precise, stating that only bare contact to the part to be tested is reliable for these contact voltage detectors. The rationale is that tests on painted or coated conductors have led to wrong indications, as this non-conductive paint or coat acts as a capacitor with different capacity according to the thickness. This capacity has an effect on the threshold voltage. b) A contact probe is introduced as a new type of non-conductive contact electrode. c) A new type "exclusively outdoor type" has been defined and implemented into the requirements and test procedure. d) A selector for voltage and frequency is allowed if foreseeable misuse is excluded. e) The marking for voltage detectors with low interference voltage has been made more precise. f) The indication groups have been made more precise and requirements and tests for the "ready to operate state" and "stand-by state" added. g) Requirements and tests for electromagnetic compatability have been implemented. h) An example for good electrical connection for the tests is introduced.

Standard
82 pages
English language
sale 10% off
e-Library read for
1 day

CLC

EN IEC 61472-2:2021(Main)

Live working - Minimum approach distances - Part 2: Method of determination of the electrical component distance for AC systems from 1,0 kV to 72,5 kV

SIST EN IEC 61472-2:2021

IEC 61472-2:2021 specifies a method for determining the electrical component of the minimum approach distances for live working, for AC systems 1 kV up to and including 72,5 kV. This document addresses system overvoltages and the working air distances between equipment and/or workers at different potentials. The withstand voltage and minimum approach distances determined by the method described in this document can be used only if the following working conditions prevail:
workers are trained for, and skilled in, working live lines or close to live conductors or equipment;
the operating conditions are adjusted so that the statistical overvoltage does not exceed the value selected for the determination of the required withstand voltage;
transient overvoltages are the determining overvoltages;
tool insulation has no continuous film of moisture present on the surface;
no lightning is observed within 10 km of the work site;
allowance is made for the effect of the conducting components of tools.

Standard
18 pages
English language
sale 10% off
e-Library read for
1 day

CLC

EN IEC 60895:2020(Main)

Live working - Conductive clothing

SIST EN IEC 60895:2020

IEC 60895:2020 is applicable to conductive clothing, worn during live working (especially bare-hand working) on AC and DC electrical installations, to provide electrical continuity between all parts of the clothing and a reduction of electric field inside the clothing. This document is applicable to conductive clothing assembled from a conductive garment (jackets and trousers or coveralls forming a one-piece garment) and from conductive component parts (gloves, hoods or helmets, shoes or boots, overshoe socks and socks) in electrical systems with nominal voltage up to 1 000 kV AC and up to ±800 kV DC. This document does not indicate values of protection from the effects of the electric arc, because any value indicated would not guarantee the necessary protection from the effects of electric arcs, or the operator would need to wear very heavy and rigid conductive clothing, which would not allow the execution of the work in safety. The products designed and manufactured according to this document contribute to the safety of the users provided they are used by persons trained for the work, in accordance with the live working methods and the instructions for use. This third edition cancels and replaces the second edition, published in 2002. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: a) increase of the use up to 1 000 kV AC and ±800 kV DC; b) introduction of two classes of conductive clothing with different electrical requirements; c) revision of the electrical requirements of conductive clothing; d) definition of specific resistance values for each component part of the conductive clothing; e) introduction of conductive helmet and conductive scarf as component parts of conductive clothing; f) introduction of mechanical requirements and new tests for fabrics; g) update of the cleaning test procedures; h) revision of the efficiency test of the conductive clothing to improve the feasibility and repeatability; i) preparation of the elements of classification of defects, and general application of IEC 61318:2007; j) the normative Annex B for the classification of tests has been replaced by normative Annex C for the general type tests procedure, the normative Annex D for the classification of defects and the informative Annex E providing the justification for the classification of defects; k) the normative Annex C on sampling procedure has been deleted (not applicable according to IEC 61318:2007); l) modification of the recommended frequency of the periodic tests.