EN IEC 60721-3-9:2024
(Main)Classification of environmental conditions - Part 3-9: Classification of groups of environmental parameters and their severities - Microclimates inside products
Classification of environmental conditions - Part 3-9: Classification of groups of environmental parameters and their severities - Microclimates inside products
IEC 60721-3-9:2024 classifies groups of microclimatic conditions, to which components (basic parts, assemblies, built-in units) can be subjected inside products, which are used under the climatic conditions as classified in IEC 60721-3-3 and IEC 60721-3-4. This second edition cancels and replaces the first edition published in 1993, Amendment 1:1994 and Corrigendum 1:1995. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: a) Clause 2 has been updated; b) Clause 4 has been re-edited and simplified; c) Annex A has been revised and updated; d) a new Annex B has been added and gives the origin of the constitutional diagram for humid air, which is the basis of drawing the climatogram for a microclimate.
Klassifizierung von Umgebungsbedingungen - Teil 3-9: Klassen von Einflussgrößen und deren Grenzwerte - Mikroklimate innerhalb von Erzeugnissen
Classification des conditions d'environnement - Partie 3-9: Classification des groupements des agents d'environnement et de leurs sévérités - Microclimats à l'intérieur des produits
L'IEC 60721-3-9:2024 classifie les groupements des conditions microclimatiques auxquelles les composants (parties élémentaires, assemblées, encastrées) peuvent être soumis à l'intérieur des produits, lorsqu'ils sont utilisés dans les conditions climatiques classifiées dans l'IEC 60721-3-3 et l'IEC 60721-3-4. Cette deuxième édition annule et remplace la première édition parue en 1993, l’Amendement 1:1994 et le Corrigendum 1:1995. Cette édition constitue une révision technique. Cette édition inclut les modifications techniques majeures suivantes par rapport à l'édition précédente: a) l’Article 2 a été mis à jour; b) l’Article 4 a été reformulé et simplifié; c) l’Annexe A a été révisée et mise à jour; d) une nouvelle Annexe B a été ajoutée et fournit l'origine du diagramme constitutionnel pour l'humidité de l'air, qui sert de base à l'établissement du climatogramme d'un microclimat.
Klasifikacija okoljskih pogojev - 3-9. del: Razvrščanje skupin okoljskih parametrov in njihove resnosti - Mikroklima v izdelkih (IEC 60721-3-9:2024)
Standard IEC 60721-3-9:2024 razvršča skupine mikroklimatskih pogojev, ki so jim lahko izpostavljene komponente (osnovni deli, sestavi, vgrajene enote) v izdelkih, ki se uporabljajo pod klimatskimi pogoji, kot je razvrščeno v standardih IEC 60721-3-3 in IEC 60721-3-4.
Druga izdaja razveljavlja in nadomešča prvo izdajo, objavljeno leta 1993, dopolnilo 1 iz leta 1994 in popravek 1 iz leta 1995. Ta izdaja je tehnično popravljena izdaja.
Ta izdaja v primerjavi s prejšnjo vključuje naslednje pomembne tehnične spremembe:
a) točka 2 je bila posodobljena;
b) točka 4 je bila na novo urejena in poenostavljena;
c) dodatek A je bil revidiran in posodobljen;
d) dodan je bil nov dodatek B, ki podaja izvor faznega diagrama za vlažen zrak, ki je osnova za risanje klimograma za mikroklimo.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-julij-2024
Klasifikacija okoljskih pogojev - 3-9. del: Razvrščanje skupin okoljskih parametrov
in njihove resnosti - Mikroklima v izdelkih (IEC 60721-3-9:2024)
Classification of environmental conditions - Part 3-9: Classification of groups of
environmental parameters and their severities - Microclimates inside products (IEC
60721-3-9:2024)
Klassifizierung von Umgebungsbedingungen - Teil 3-9: Klassen von Einflussgrößen und
deren Grenzwerte - Mikroklimate innerhalb von Erzeugnissen (IEC 60721-3-9:2024)
Classification des conditions d'environnement - Partie 3-9: Classification des
groupements des agents d'environnement et de leurs sévérités - Microclimats à
l'intérieur des produits (IEC 60721-3-9:2024)
Ta slovenski standard je istoveten z: EN IEC 60721-3-9:2024
ICS:
19.040 Preskušanje v zvezi z Environmental testing
okoljem
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD EN IEC 60721-3-9
NORME EUROPÉENNE
EUROPÄISCHE NORM May 2024
ICS 19.040 Supersedes EN 60721-3-9:1993;
EN 60721-3-9:1993/A1:1995
English Version
Classification of environmental conditions - Part 3-9:
Classification of groups of environmental parameters and their
severities - Microclimates inside products
(IEC 60721-3-9:2024)
Classification des conditions d'environnement - Partie 3-9: Klassifizierung von Umgebungsbedingungen - Teil 3-9:
Classification des groupements des agents Klassen von Einflussgrößen und deren Grenzwerte -
d'environnement et de leurs sévérités - Microclimats à Mikroklimate innerhalb von Erzeugnissen
l'intérieur des produits (IEC 60721-3-9:2024)
(IEC 60721-3-9:2024)
This European Standard was approved by CENELEC on 2024-05-16. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Türkiye and the United Kingdom.
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2024 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN IEC 60721-3-9:2024 E
European foreword
The text of document 104/1041/FDIS, future edition 2 of IEC 60721-3-9, prepared by IEC/TC 104
"Environmental conditions, classification and methods of test" was submitted to the IEC-CENELEC
parallel vote and approved by CENELEC as EN IEC 60721-3-9:2024.
The following dates are fixed:
• latest date by which the document has to be implemented at national (dop) 2025-02-16
level by publication of an identical national standard or by endorsement
• latest date by which the national standards conflicting with the (dow) 2027-05-16
document have to be withdrawn
This document supersedes EN 60721-3-9:1993 and all of its amendments and corrigenda (if any).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
Any feedback and questions on this document should be directed to the users’ national committee. A
complete listing of these bodies can be found on the CENELEC website.
Endorsement notice
The text of the International Standard IEC 60721-3-9:2024 was approved by CENELEC as a
European Standard without any modification.
In the official version, for Bibliography, the following note has to be added for the standard indicated:
IEC 60721-2-1:2013 NOTE Approved as EN 60721-2-1:2014 (not modified)
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments)
applies.
NOTE 1 Where an International Publication has been modified by common modifications, indicated by (mod), the
relevant EN/HD applies.
NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is available
here: www.cencenelec.eu.
Publication Year Title EN/HD Year
IEC 60721-1 - Classification of environmental conditions - EN 60721-1 -
Part 1: Environmental parameters and their
severities
IEC 60721-3-0 2020 Classification of environmental conditions - EN IEC 60721-3-0 2020
Part 3-0: Classification of groups of
environmental parameters and their
severities - Introduction
IEC 60721-3-3 2019 Classification of environmental conditions - EN IEC 60721-3-3 2019
Part 3-3: Classification of groups of
environmental parameters and their
severities - Stationary use at
weatherprotected locations
IEC 60721-3-4 2019 Classification of environmental conditions - EN IEC 60721-3-4 2019
Part 3-4: Classification of groups of
environmental parameters and their
severities - Stationary use at non-
weatherprotected locations
IEC 60721-3-9 ®
Edition 2.0 2024-04
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Classification of environmental conditions –
Part 3-9: Classification of groups of environmental parameters and their
severities – Microclimates inside products
Classification des conditions d'environnement –
Partie 3-9: Classification des groupements des agents d'environnement et de
leurs sévérités – Microclimats à l'intérieur des produits
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 19.040 ISBN 978-2-8322-8626-5
– 2 – IEC 60721-3-9:2024 © IEC 2024
CONTENTS
FOREWORD . 3
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 5
4 General . 6
5 Classification of microclimatic conditions . 6
6 Types and marking of microclimatic classes . 7
Annex A (informative) Graphical representation and preferred microclimatic classes . 8
A.1 Graphical representation of the microclimatic classes . 8
A.2 Tables of preferred microclimatic classes . 9
Annex B (informative) Constitutional diagram for humid air . 14
B.1 General . 14
B.2 Application . 14
B.3 Description . 14
Bibliography . 17
Figure A.1 – Example of a climatogram for a microclimate: Microclimatic class
3K22/X2/Y1 . 9
Figure B.1 – Constitutional diagram for humid air . 16
Table 1 – Classification of microclimatic conditions . 7
Table A.1 – Characteristic parameters and severities of microclimatic classes –
Weatherprotected locations: Corner points A’, B’, C’, D’, E’ and F’ . 10
Table A.2 – Characteristic parameters and severities of microclimatic classes –
Weatherprotected locations: Corner points B to B and C to C . 11
Y1 Y4 Y1 Y4
Table A.3 – Characteristic parameters and severities of microclimatic classes –
Non-weatherprotected locations: Corner points A’, B’, C’, D’, E’ and F’ . 12
Table A.4 – Characteristic parameters and severities of microclimatic classes –
Non-weatherprotected locations: Corner points B to B and C to C . 13
Y1 Y4 Y1 Y4
IEC 60721-3-9:2024 © IEC 2024 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
CLASSIFICATION OF ENVIRONMENTAL CONDITIONS –
Part 3-9: Classification of groups of environmental parameters
and their severities – Microclimates inside products
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international
co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and
in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports,
Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their
preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with
may participate in this preparatory work. International, governmental and non-governmental organizations liaising
with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for
Standardization (ISO) in accordance with conditions determined by agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence between
any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) IEC draws attention to the possibility that the implementation of this document may involve the use of (a)
patent(s). IEC takes no position concerning the evidence, validity or applicability of any claimed patent rights in
respect thereof. As of the date of publication of this document, IEC had not received notice of (a) patent(s), which
may be required to implement this document. However, implementers are cautioned that this may not represent
the latest information, which may be obtained from the patent database available at https://patents.iec.ch. IEC
shall not be held responsib
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.