EN 61300-3-35:2015
(Main)Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 3-35: Examinations and measurements - Visual inspection of fibre optic connectors and fibre-stub transceivers
Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 3-35: Examinations and measurements - Visual inspection of fibre optic connectors and fibre-stub transceivers
IEC 61300-3-35:2015 is available as IEC 61300-3-35:2015 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition. IEC 61300-3-35:2015 describes methods for quantitatively assessing the end face quality of a polished fibre optic connector or of a fibre optic transceiver using a fibre-stub type interface. Sub-surface cracks and fractures are not considered in this standard. In general, the methods described in this standard apply to 125 μ cladding fibres contained within a ferrule and intended for use with sources of ≤ 2 W of input power. However, portions are applicable to non-ferruled connectors and other fibre types. Those portions are identified where appropriate. It is not the intention of this standard that the size of scratches should be measured, the dimensions and requirements are selected such that they can be estimated. There is no need to measure for example if a scratch is 2,3 μm wide. This second edition cancels and replaces the first edition published in 2009 and constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: - modification to the title; - addition of some terms and definitions; - reconsideration of the specific values of Tables 1 to 4 to reflect the current market situation; - addition of visual requirements for single-mode transceivers using a fibre-stub interface in Table 3; - addition of a sentence in 4.1 concerning the susceptibility of the methods to system variability. Keywords: end face quality of a polished fibre optic connector, fibre optic transceiver using a fibre-stub type interface
Lichtwellenleiter - Verbindungselemente und passive Bauteile - Grundlegende Prüf- und Messverfahren - Teil 3-35: Untersuchungen und Messungen - Visuelle Inspektion von Lichtwellenleiter-Steckverbindern und Faser Stub-Transceivern
Dispositifs d'interconnexion et composants passifs à fibres optiques - Procédures fondamentales d’essais et de mesures - Partie 3-35: Examens et mesures - Examen visuel des connecteurs à fibres optiques et des émetteurs-récepteurs à embase fibrée
L'IEC 61300-3-35:2015 est disponible sous forme de IEC 61300-3-35:2015 RLV qui contient la Norme internationale et sa version Redline, illustrant les modifications du contenu technique depuis l'édition précédente. L'IEC 61300-3-35:2015 décrit des méthodes pour évaluer quantitativement la qualité de l'extrémité d'un connecteur à fibres optiques polies ou d'un émetteur-récepteur à fibres optiques utilisant une interface de type à embase fibrée. Les craquelures et fractures internes ne sont pas traitées dans la présente norme. En général, les méthodes décrites dans la présente norme s'appliquent aux fibres à gaine de 125 μ contenues dans une férule et destinées à être utilisées avec des sources de puissance d'entrée ≤ 2 W. Toutefois, des parties sont applicables aux connecteurs exempts de férules et autres types de fibres. Ces parties sont identifiées s'il y lieu. La présente norme n'a pas pour objet de préconiser le mesurage de la taille des éraflures; les dimensions et les exigences sont choisies de telle sorte à pouvoir les estimer. Un mesurage n'est pas nécessaire dans le cas où, par exemple, la largeur de l'éraflure est égale à 2,3 μ. Cette deuxième édition annule et remplace la première édition parue en 2009. Cette édition constitue une révision technique. Cette édition inclut les modifications techniques majeures suivantes par rapport à l'édition précédente: - modification du titre; - ajout de termes et définitions; - révision des valeurs spécifiques des Tableaux 1 à 4 en vue de refléter les réalités actuelles du marché; - ajout dans le Tableau 3 des exigences visuelles relatives aux émetteurs-récepteurs unimodaux utilisant une interface à embase fibrée; - ajout d'une phrase en 4.1 précisant que les méthodes sont sujettes à une variabilité du système. Mots clés: qualité de l'extrémité d'un connecteur à fibres optiques polies, d'un émetteur-récepteur à fibres optiques utilisant une interface de type à embase fibrée
Optični spojni elementi in pasivne komponente - Osnovni preskusni in merilni postopki - 3-35. del: Preiskave in meritve - Vizualno pregledovanje optičnih konektorjev in sprejemnikov-oddajnikov z vlakenskimi tulkami (IEC 61300-3-35:2015)
Ta del standarda IEC 61300 opisuje metode za kvantitativno ocenjevanje končne kakovosti poliranega optičnega konektorja ali optičnega sprejemnika-oddajnika z uporabo vmesnika z vlakenskimi tulkami. Podpovršinske razpoke v tem standardu niso zajete. Metode, opisane v tem standardu, se v splošnem uporabljajo za vlakna z oblogo 125 μm, ki so znotraj tulke in so namenjena za uporabo z viri vhodne moči ≤ 2 W. Deloma se uporabljajo tudi za konektorje brez tulke in druge vrste vlaken. To je ustrezno opredeljeno. Namen tega standarda ni natančna meritev velikosti prask, temveč izbira dimenzij in zahtev, ki omogočajo njihovo oceno. Meritev praske s širino 2,3 μm na primer ni potrebna.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-maj-2016
1DGRPHãþD
SIST EN 61300-3-35:2010
2SWLþQLVSRMQLHOHPHQWLLQSDVLYQHNRPSRQHQWH2VQRYQLSUHVNXVQLLQPHULOQL
SRVWRSNLGHO3UHLVNDYHLQPHULWYH9L]XDOQRSUHJOHGRYDQMHRSWLþQLK
NRQHNWRUMHYLQVSUHMHPQLNRYRGGDMQLNRY]YODNHQVNLPLWXONDPL,(&
Fibre optic interconnecting devices and passive components - Basic test and
measurement procedures - Part 3-35: Examinations and measurements - Visual
inspection of fibre optic connectors and fibre-stub transceivers (IEC 61300-3-35:2015)
Lichtwellenleiter - Verbindungselemente und passive Bauteile - Grundlegende Prüf- und
Messverfahren - Teil 3-35: Untersuchungen und Messungen - Visuelle Inspektion von
Lichtwellenleiter-Steckverbindern und Faser Stub-Transceivern (IEC 61300-3-35:2015)
Dispositifs d'interconnexion et composants passifs à fibres optiques - Procédures
fondamentales d'essais et de mesures - Partie 3-35: Examens et mesures - Examen
visuel des connecteurs à fibres optiques et des émetteurs-récepteurs à embase fibrée
(IEC 61300-3-35:2015)
Ta slovenski standard je istoveten z: EN 61300-3-35:2015
ICS:
33.180.20 3RYH]RYDOQHQDSUDYH]D Fibre optic interconnecting
RSWLþQDYODNQD devices
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD EN 61300-3-35
NORME EUROPÉENNE
EUROPÄISCHE NORM
October 2015
ICS 33.180.20 Supersedes EN 61300-3-35:2010
English Version
Fibre optic interconnecting devices and passive components -
Basic test and measurement procedures - Part 3-35:
Examinations and measurements - Visual inspection of fibre
optic connectors and fibre-stub transceivers
(IEC 61300-3-35:2015)
Dispositifs d'interconnexion et composants passifs à fibres Lichtwellenleiter - Verbindungselemente und passive
optiques - Procédures fondamentales d'essais et de Bauteile - Grundlegende Prüf- und Messverfahren - Teil 3-
mesures - Partie 3-35: Examens et mesures - Examen 35: Untersuchungen und Messungen - Visuelle Inspektion
visuel des connecteurs à fibres optiques et des émetteurs- von Lichtwellenleiter-Steckverbindern und Faser Stub-
récepteurs à embase fibrée Transceivern
(IEC 61300-3-35:2015) (IEC 61300-3-35:2015)
This European Standard was approved by CENELEC on 2015-07-30. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2015 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN 61300-3-35:2015 E
European foreword
The text of document 86B/3886/FDIS, future edition 2 of IEC 61300-3-35, prepared by SC 86B “Fibre
optic interconnecting devices and passive components” of IEC/TC 86 “Fibre optics" was submitted to
the IEC-CENELEC parallel vote and approved by CENELEC as EN 61300-3-35:2015.
The following dates are fixed:
(dop) 2016-04-30
• latest date by which the document has to be
implemented at national level by
publication of an identical national
standard or by endorsement
• latest date by which the national (dow) 2018-07-30
standards conflicting with the
document have to be withdrawn
This document supersedes EN 61300-3-35:2010.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC [and/or CEN] shall not be held responsible for identifying any or all such
patent rights.
Endorsement notice
The text of the International Standard IEC 61300-3-35:2015 was approved by CENELEC as a
European Standard without any modification.
In the official version, for Bibliography, the following notes have to be added for the standards
indicated:
IEC 60825-2 NOTE Harmonized as EN 60825-2
IEC 61300-1 NOTE Harmonized as EN 61300-1
IEC 61755 (Series) NOTE Harmonized as EN 61755 (Series)
IEC 61300-3-35 ®
Edition 2.0 2015-06
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
colour
inside
Fibre optic interconnecting devices and passive components – Basic test and
measurement procedures –
Part 3-35: Examinations and measurements –
Visual inspection of fibre optic connectors and fibre-stub transceivers
Dispositifs d'interconnexion et composants passifs à fibres optiques –
Procédures fondamentales d’essais et de mesures –
Partie 3-35: Examens et mesures – Examen visuel des connecteurs à fibres
optiques et des émetteurs-récepteurs à embase fibrée
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 33.180.20 ISBN 978-2-8322-2716-9
– 2 – IEC 61300-3-35:2015 © IEC 2015
CONTENTS
FOREWORD . 4
1 Scope . 6
2 Normative references . 6
3 Terms, definitions and abbreviations . 6
3.1 Terms and definitions . 6
3.2 Abbreviations . 7
4 Measurement . 7
4.1 General . 7
4.2 Measurement conditions . 7
4.3 Pre-conditioning . 7
4.4 Recovery . 7
5 Apparatus . 8
5.1 Method A: Direct view optical microscopy . 8
5.2 Method B: Video microscopy . 8
5.3 Method C: Automated analysis microscopy . 8
5.4 Certification requirements for low and high resolution systems . 8
5.4.1 General . 8
5.4.2 Requirement for low resolution microscope systems . 8
5.4.3 Requirements for high resolution microscope systems . 9
6 Procedure . 9
6.1 Certification procedure . 9
6.2 Inspection procedure . 9
6.3 Visual requirements . 10
Annex A (informative) Examples of inspected end faces with surface anomalies . 13
Annex B (normative) Diagram of qualification artefact and method of manufacture . 18
B.1 High resolution artefact . 18
B.2 Low resolution artefact . 20
Bibliography . 21
Figure 1 – Inspection procedure flow . 10
Figure A.1 – Example 1 (low resolution system) . 13
Figure A.2 – Example 1 (high resolution system) . 13
Figure A.3 – Example 2 (low resolution system) . 14
Figure A.4 – Example 2 (high resolution system) . 14
Figure A.5 – Example 3 (low resolution system) . 14
Figure A.6 – Example 3 (high resolution system) . 15
Figure A.7 – Example 4 (low resolution system) . 15
Figure A.8 – Example 4 (high resolution system) . 16
Figure A.9 – Example 5 (low resolution system) . 16
Figure A.10 – Example 6 (low resolution system) . 17
Figure B.1 – Example of nano-indentation test system . 18
Figure B.2 – Example of high resolution artefacts . 19
Figure B.3 – Example of low resolution artefact pattern . 20
IEC 61300-3-35:2015 © IEC 2015 – 3 –
Table 1 – Visual requirements for single-mode PC polished connectors, RL ≥ 45 dB . 11
Table 2 – Visual requirements for single-mode angle polished (APC) connectors . 11
Table 3 – Visual requirements for single-mode PC polished connectors, RL ≥ 26 dB
and single-mode transceivers using a fibre-stub interface . 12
Table 4 – Visual requirements for multi-mode PC polished connectors . 12
– 4 – IEC 61300-3-35:2015 © IEC 2015
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
FIBRE OPTIC INTERCONNECTING
DEVICES AND PASSIVE COMPONENTS –
BASIC TEST AND MEASUREMENT PROCEDURES –
Part 3-35: Examinations and measurements –
Visual inspection of fibre optic connectors and fibre-stub transceivers
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of c
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.