ETSI EN 300 113-1 V1.7.1 (2011-11)
Electromagnetic compatibility and Radio spectrum Matters (ERM); Land mobile service; Radio equipment intended for the transmission of data (and/or speech) using constant or non-constant envelope modulation and having an antenna connector; Part 1: Technical characteristics and methods of measurement
Electromagnetic compatibility and Radio spectrum Matters (ERM); Land mobile service; Radio equipment intended for the transmission of data (and/or speech) using constant or non-constant envelope modulation and having an antenna connector; Part 1: Technical characteristics and methods of measurement
REN/ERM-TGDMR-296-1
Elektromagnetna združljivost in zadeve v zvezi z radijskim spektrom (ERM) - Storitev kopenskih mobilnih komunikacij - Radijska oprema za prenos podatkov (oziroma govora), ki uporablja modulacijo s konstantno ali nekonstantno ovojnico in ima antenski priključek - 1. del: Tehnične karakteristike in merilne metode
Ta dokument zajema tehnične zahteve za radijske oddajnike in sprejemnike, ki se uporabljajo v postajah za storitev zasebnega mobilnega radia (PMR).
Obravnava uporabo storitve kopenskih mobilnih komunikacij, ki deluje na radijskih frekvencah med 30 MHz in 1 GHz, ima medkanalske razmike 12,5 kHz, 20 kHz in 25 kHz in je namenjena za govor in/ali podatke.
Obravnava opremo za neprekinjen in/ali prekinjen prenos podatkov in/ali digitalnega govora.
Oprema obsega oddajnik ter ustrezen kodirnik in modulator in/ali sprejemnik ter ustrezen demodulator in odkodirnik. Ta dokument zajema naslednje vrste opreme:
• bazna postaja (oprema z antenskim priključkom, namenjena za uporabo na stalni lokaciji);
• mobilna postaja (oprema z antenskim priključkom, ki se običajno uporablja v vozilu ali prenosno);
in
• prenosne postaje:
a) z antenskim priključkom ali
b) brez zunanjega antenskega priključka, vendar s stalnim ali začasnim notranjim 50-
Ω radijskofrekvenčnim (RF) priključkom, ki omogoča dostop do izhoda oddajnika in vhoda sprejemnika.
Prenosna oprema brez zunanjega ali notranjega radijskofrekvenčnega priključka in brez možnosti namestitve začasnega notranjega 50-
Ω priključka ni zajeta v tem dokumentu.
General Information
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Electromagnetic compatibility and Radio spectrum Matters (ERM) - Land mobile service - Radio equipment intended for the transmission of data (and/or speech) using constant or non-constant envelope modulation and having an antenna connector - Part 1: Technical characteristics and methods of measurement33.100.01Elektromagnetna združljivost na splošnoElectromagnetic compatibility in general33.070.01Mobilni servisi na splošnoMobile services in general33.060.99Druga oprema za radijske komunikacijeOther equipment for radiocommunicationsICS:Ta slovenski standard je istoveten z:EN 300 113-1 Version 1.7.1SIST EN 300 113-1 V1.7.1:2012en01-februar-2012SIST EN 300 113-1 V1.7.1:2012SLOVENSKI
STANDARD
SIST EN 300 113-1 V1.7.1:2012
ETSI EN 300 113-1 V1.7.1 (2011-11) Electromagnetic compatibility and Radio spectrum Matters (ERM); Land mobile service; Radio equipment intended for the transmission of data (and/or speech) using constant or non-constant envelope modulation and having an antenna connector; Part 1: Technical characteristics and methods of measurement
European Standard SIST EN 300 113-1 V1.7.1:2012
ETSI ETSI EN 300 113-1 V1.7.1 (2011-11) 2
Reference REN/ERM-TGDMR-296-1 Keywords antenna, data, mobile, PMR, radio, speech ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00
Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C Association à but non lucratif enregistrée à la Sous-Préfecture de Grasse (06) N° 7803/88
Important notice Individual copies of the present document can be downloaded from: http://www.etsi.org The present document may be made available in more than one electronic version or in print. In any case of existing or perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF). In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at http://portal.etsi.org/tb/status/status.asp If you find errors in the present document, please send your comment to one of the following services: http://portal.etsi.org/chaircor/ETSI_support.asp Copyright Notification No part may be reproduced except as authorized by written permission. The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2011. All rights reserved.
DECTTM, PLUGTESTSTM, UMTSTM and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members. 3GPPTM and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association. SIST EN 300 113-1 V1.7.1:2012
ETSI ETSI EN 300 113-1 V1.7.1 (2011-11) 3 Contents Intellectual Property Rights . 8 Foreword . 8 1 Scope . 9 2 References . 9 2.1 Normative references . 9 2.2 Informative references . 10 3 Definitions, symbols and abbreviations . 10 3.1 Definitions . 10 3.2 Symbols . 11 3.3 Abbreviations . 12 4 General . 12 4.1 Presentation of equipment for testing purposes . 12 4.1.1 Choice of model for testing . 12 4.1.1.1 Auxiliary test equipment . 13 4.1.1.2 Declarations by the provider . 13 4.2 Mechanical and electrical design . 13 4.2.1 General . 13 4.2.2 Controls . 13 4.2.3 Transmitter shut-off facility . 13 4.3 Marking . 13 4.4 Testing using bit streams or messages . 13 4.5 Measuring continuous mode equipment . 13 4.6 Measuring discontinuous mode equipment . 14 4.7 Combined full bandwidth analogue speech/full bandwidth digital equipment . 14 4.8 Constant and non-constant envelope modulation . 15 5 Test conditions, power sources and ambient temperatures . 15 5.1 Normal and extreme test conditions . 15 5.2 Test power source . 15 5.3 Normal test conditions . 15 5.3.1 Normal temperature and humidity . 15 5.3.2 Normal test power source . 16 5.3.2.1 Mains voltage . 16 5.3.2.2 Regulated lead-acid battery power sources used on vehicles . 16 5.3.2.3 Other power sources . 16 5.4 Extreme test conditions . 16 5.4.1 Extreme temperatures . 16 5.4.2 Extreme test source voltages . 16 5.4.2.1 Mains voltage . 16 5.4.2.2 Regulated lead-acid battery power sources used on vehicles . 16 5.4.2.3 Power sources using other types of batteries . 16 5.4.2.4 Other power sources . 17 5.5 Procedure for tests at extreme temperatures . 17 5.5.1 Procedure for equipment designed for continuous transmission. 17 5.5.2 Procedure for equipment designed for intermittent transmission . 17 5.5.3 Testing of equipment that does not have an external 50 Ω RF connector (integral antenna equipment) . 17 6 General test conditions . 18 6.1 Arrangements for test signals applied to the receiver input . 18 6.2 Receiver mute or squelch facility . 18 6.3 Normal test signals (wanted and unwanted signals) . 18 6.3.1 Equipment measured as constant envelope angle modulation equipment . 18 6.3.2 Equipment measured as non-constant envelope modulation equipment . 19 6.4 Encoder for receiver measurements . 19 SIST EN 300 113-1 V1.7.1:2012
ETSI ETSI EN 300 113-1 V1.7.1 (2011-11) 4 6.5 Transceiver data interface. 20 6.6 Impedance . 20 6.7 Artificial antenna . 20 6.8 Tests of equipment with a duplex filter . 20 6.9 Facilities for access . 20 6.9.1 Analogue access . 20 6.9.2 Test points for bit stream measurements. 20 6.9.3 Coupling arrangements . 21 6.9.3.1 Arrangements for measurements with continuous bit streams . 21 6.9.3.2 Arrangements for measurements with messages . 21 6.10 Test site and general arrangements for measurements involving the use of radiated fields . 21 6.11 Modes of operation of the transmitter for constant envelope equipment . 21 7 Technical characteristics of the transmitter . 22 7.1 Frequency error . 22 7.1.1 Definition . 22 7.1.2 Method of measurement . 22 7.1.3 Limits . 22 7.2 Transmitter power (conducted) . 23 7.2.1 Definitions . 23 7.2.1.1 Equipment measured as constant envelope angle modulation equipment . 23 7.2.1.2 Equipment measured as non-constant envelope modulation equipment . 23 7.2.2 Method of measurement . 23 7.2.2.1 Equipment measured as constant envelope angle modulation equipment . 23 7.2.2.2 Equipment measured as non-constant envelope modulation equipment . 24 7.2.3 Limits . 24 7.3 Maximum Effective radiated power . 24 7.3.1 Definition . 24 7.3.1.1 Equipment measured as constant envelope angle modulation equipment . 24 7.3.1.2 Equipment measured as non-constant envelope modulation equipment . 25 7.3.2 Methods of measurement . 25 7.3.2.1 Equipment measured as constant envelope angle modulation equipment . 26 7.3.2.2 Equipment measured as non-constant envelope modulation equipment . 27 7.3.3 Limits . 28 7.4 Adjacent channel power . 29 7.4.1 Definition . 29 7.4.2 Method of measurement . 29 7.4.3 Limits . 30 7.5 Unwanted emissions in the spurious domain. 31 7.5.1 Definition . 31 7.5.2 Method of measuring the power level . 31 7.5.2.1 Equipment measured as constant envelope angle modulation equipment . 32 7.5.2.2 Equipment measured as non-constant envelope modulation equipment . 32 7.5.3 Method of measuring the effective radiated power . 32 7.5.3.1 Equipment measured as constant envelope angle modulation equipment . 33 7.5.3.2 Equipment measured as non-constant envelope modulation equipment . 33 7.5.4 Limits . 35 7.6 Intermodulation attenuation. 36 7.6.1 Definition . 36 7.6.2 Method of measurement . 36 7.6.3 Limits . 37 7.7 Transmitter attack time . 37 7.7.1 Definition . 37 7.7.2 Method of measurement . 38 7.7.3 Limit . 38 7.8 Transmitter release time . 38 7.8.1 Definition . 38 7.8.2 Method of measurement . 39 7.8.3 Limits . 39 7.9 Transient behaviour of the transmitter . 39 7.9.1 Definitions . 39 7.9.2 Timings, frequencies and powers . 41 SIST EN 300 113-1 V1.7.1:2012
ETSI ETSI EN 300 113-1 V1.7.1 (2011-11) 5 7.9.3 Methods of measurement . 44 7.9.3.1 Time domain measurements of power and frequency . 44 7.9.3.2 Test arrangement and characteristics of the FM modulation meter . 45 7.9.3.3 Adjacent channel transient power measurements . 45 7.9.3.3.1 Definition. 45 7.9.3.3.2 Measurement method for constant envelope angle modulation equipment . 45 7.9.3.3.3 Measurement method for non-constant envelope modulation equipment . 46 7.9.3.3.4 Alternative measurement method using a spectrum analyser . 47 7.9.3.4 Characteristics of the adjacent channel transient power measuring device . 48 7.9.4 Limits . 48 7.9.4.1 Time domain analysis of power and frequency for constant envelope transmissions . 49 7.9.4.2 Adjacent and alternate channel transient power . 49 7.9.4.2.1 Equipment measured as constant envelope angle modulation equipment . 49 7.9.4.2.2 Equipment measured as non-constant envelope modulation equipment . 49 8 Methods of measurement for receiver parameters . 50 8.1 Maximum usable sensitivity (conducted) . 50 8.1.1 Definition . 50 8.1.2 Method of measurement . 50 8.1.2.1 Method of measurement with continuous bit streams . 50 8.1.2.2 Method of measurement with messages . 51 8.1.2.3 Method of measurement with packets . 51 8.1.3 Limits . 52 8.2 Average usable sensitivity (field strength) . 52 8.2.1 Definition . 52 8.2.2 Method of measurement . 52 8.2.3 Limits . 53 8.3 Level of the wanted signal for the degradation measurements . 53 8.4 Error behaviour at high input levels . 54 8.4.1 Definition . 54 8.4.2 Method of measurement . 54 8.4.2.1 Method of measurement with continuous bit streams . 54 8.4.2.2 Method of measurement with messages . 54 8.4.2.3 Method of measurement with packets . 55 8.4.3 Limits . 55 8.5 Co-channel rejection. 55 8.5.1 Definition . 55 8.5.2 Method of measurement . 56 8.5.2.1 Method of measurement with continuous bit streams . 56 8.5.2.2 Method of measurement with messages . 57 8.5.2.3 Method of measurement with packets . 58 8.5.3 Limits . 58 8.6 Adjacent channel selectivity . 59 8.6.1 Definition . 59 8.6.2 Method of measurement . 59 8.6.2.1 Method of measurement with continuous bit streams . 59 8.6.2.2 Method of measurement with messages . 60 8.6.2.3 Method of measurement with packets . 61 8.6.3 Limits . 62 8.7 Spurious response rejection . 62 8.7.1 Definition . 62 8.7.2 Introduction to the method of measurement . 62 8.7.3 Method of search over the "limited frequency range" . 63 8.7.4 Method of measurement with continuous bit streams . 64 8.7.5 Method of measurement with messages . 64 8.7.6 Method of measurement with packets . 65 8.7.7 Limits . 66 8.8 Intermodulation response rejection . 66 8.8.1 Definition . 66 8.8.2 Method of measurement . 67 8.8.2.1 Method of measurement with continuous bit streams . 67 8.8.2.2 Method of measurement with messages . 68 SIST EN 300 113-1 V1.7.1:2012
ETSI ETSI EN 300 113-1 V1.7.1 (2011-11) 6 8.8.2.3 Method of measurement
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.