ETSI EN 302 878-2 V1.1.1 (2011-11)
Access, Terminals, Transmission and Multiplexing (ATTM); Third Generation Transmission Systems for Interactive Cable Television Services - IP Cable Modems; Part 2: Physical Layer; DOCSIS 3.0
Access, Terminals, Transmission and Multiplexing (ATTM); Third Generation Transmission Systems for Interactive Cable Television Services - IP Cable Modems; Part 2: Physical Layer; DOCSIS 3.0
DEN/ATTM-003006-2
Dostop, priključki, prenos in multipleksiranje (ATTM) - Tretja generacija prenosnih sistemov za storitve interaktivne kabelske televizije - IP-kabelski modemi - 2. del: Fizična plast - DOCSIS 3.0
Ta dokument je del skupine, ki opredeljuje tretjo generacijo sistemov hitrega prenosa podatkov prek kabelskega omrežja. Ta serija je bila razvita za panogo kabelskih omrežij ter vključuje prispevke operaterjev in prodajalcev iz Severne Amerike, Evrope in drugih regij.
Med praksami načrtovanja kabelskega spektra, sprejetimi za različna omrežja po svetu, obstajajo razlike. Zato sta za tehnologijo fizične plasti vključeni dve enakovredni možnosti, pri čemer ni treba, da sta interoperabilni. Ena možnost temelji na navzdolnji večprogramski televizijski distribuciji, ki se uporablja v Severni Ameriki in pri kateri imajo kanali pasovno širino 6 MHz. Druga možnost temelji na ustrezni evropski večprogramski televizijski distribuciji. Obe možnosti imata enak status, čeprav struktura dokumenta ne odraža njune enakovrednosti. Prva možnost je opredeljena v točkah 4 in 6, druga pa z zamenjavo vsebine omenjenih točk z dodatkom B. Skladno s tem [17] in [1] veljata le za prvo možnost, [3] pa le za drugo. Skladnost s tem dokumentom pomeni skladnost z eno opisano izvedbo in ne z obema. Interoperabilnost opreme, izdelane v skladu s prvo možnostjo, z opremo, izdelano v skladu z drugo možnostjo, ni zahtevana.
Ti izbirni tehnologiji fizične plasti operaterjem omogočata prilagodljivost na področjih delovanja, za katera so pooblaščeni, vključno z načrtovanjem frekvence, elektromagnetno združljivostjo (EMC) ter varnostnimi zahtevami. Možnost iz točk 5 in 6, ki temelji na navzdolnjih kanalih s širino 6 MHz, se lahko na primer uporabi tudi za načrt kanalov s širino 8 MHz. Skladnost z načrtovanjem frekvence in zahtevami elektromagnetne združljivosti v tej specifikaciji ni obravnavana ter ostaja v odgovornosti operaterjev. V zvezi s tem [13] in [14] veljata za Severno Ameriko, [i.1], [5], [7], [8], [6], [9], [10] in [11] pa za Evropsko unijo.
Združljivost s prejšnjimi različicami te tehnologije [12] je zagotovljena le znotraj posameznih možnosti, omenjenih zgoraj, in ne med obema možnostma.
General Information
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Access, Terminals, Transmission and Multiplexing (ATTM) - Third Generation Transmission Systems for Interactive Cable Television Services - IP Cable Modems - Part 2: Physical Layer - DOCSIS 3.035.180Terminalska in druga periferna oprema ITIT Terminal and other peripheral equipment35.100.10Physical layerICS:Ta slovenski standard je istoveten z:EN 302 878-2 Version 1.1.1SIST EN 302 878-2 V1.1.1:2012en01-februar-2012SIST EN 302 878-2 V1.1.1:2012SLOVENSKI
STANDARD
SIST EN 302 878-2 V1.1.1:2012
ETSI EN 302 878-2 V1.1.1 (2011-11) Access, Terminals, Transmission and Multiplexing (ATTM); Third Generation Transmission Systems for Interactive Cable Television Services - IP Cable Modems; Part 2: Physical Layer; DOCSIS 3.0
European Standard SIST EN 302 878-2 V1.1.1:2012
ETSI ETSI EN 302 878-2 V1.1.1 (2011-11) 2
Reference DEN/ATTM-003006-2 Keywords access, broadband, cable, data, IP, IPCable, modem ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00
Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C Association à but non lucratif enregistrée à la Sous-Préfecture de Grasse (06) N° 7803/88
Important notice Individual copies of the present document can be downloaded from: http://www.etsi.org The present document may be made available in more than one electronic version or in print. In any case of existing or perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF). In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at http://portal.etsi.org/tb/status/status.asp If you find errors in the present document, please send your comment to one of the following services: http://portal.etsi.org/chaircor/ETSI_support.asp Copyright Notification No part may be reproduced except as authorized by written permission. The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2011. All rights reserved.
DECTTM, PLUGTESTSTM, UMTSTM and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members. 3GPPTM and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association. SIST EN 302 878-2 V1.1.1:2012
ETSI ETSI EN 302 878-2 V1.1.1 (2011-11) 3 Contents Intellectual Property Rights . 9 Foreword . 9 1 Scope . 10 1.1 Introduction and Purpose . 10 1.2 Requirements . 10 1.3 Conventions . 10 2 References . 11 2.1 Normative references . 11 2.2 Informative references . 12 3 Definitions and abbreviations . 12 3.1 Definitions . 12 3.2 Abbreviations . 18 4 Void . 20 5 Functional Assumptions . 20 5.1 Equipment Assumptions . 20 5.1.1 Frequency Plan . 20 5.1.2 Compatibility with Other Services . 20 5.1.3 Fault Isolation Impact on Other Users . 20 5.1.4 Cable System Terminal Devices . 21 5.2 RF Channel Assumptions . 21 5.2.1 Transmission Downstream . 21 5.2.2 Transmission Upstream . 21 5.2.2.1 Availability. 22 5.3 Transmission Levels . 22 5.4 Frequency Inversion . 22 6 Physical Media Dependent Sublayer Specification . 23 6.1 Scope . 23 6.2 Upstream . 23 6.2.1 Overview . 23 6.2.2 Signal Processing Requirements . 24 6.2.3 Modulation Formats . 26 6.2.4 R-S Encode . 27 6.2.4.1 R-S Encode Modes . 27 6.2.4.2 R-S Bit-to-Symbol Ordering . 27 6.2.5 Upstream R-S Frame Structure for DOCSIS 3.0 Multiple Transmit Channel mode Enabled . 27 6.2.5.1 R-S Codeword Length. 28 6.2.5.1.1 Burst Size . 28 6.2.5.1.2 Fixed Codeword Length . 28 6.2.5.1.3 Shortened Last Codeword . 29 6.2.5.2 R-S FEC Disabled . 29 6.2.6 Upstream R-S Frame Structure for DOCSIS 3.0 Multiple Transmit Channel mode Not Enabled . 29 6.2.7 TDMA Byte Interleaver . 29 6.2.7.1 Byte Interleaver Parameters . 29 6.2.7.2 Interleaver Operating Modes . 30 6.2.7.2.1 Fixed Mode . 30 6.2.7.2.2 Dynamic Mode . 31 6.2.8 Scrambler (Randomizer) . 32 6.2.9 TCM Encoder . 33 6.2.9.1 Byte to TCM Symbol Mapping . 33 6.2.10 Preamble Prepend . 35 6.2.11 Modulation Rates . 36 6.2.11.1 DOCSIS 3.0 Modulation Rates . 36 6.2.11.2 Backward Compatibility Modulation Rates . 36 SIST EN 302 878-2 V1.1.1:2012
ETSI ETSI EN 302 878-2 V1.1.1 (2011-11) 4 6.2.12 S-CDMA Framer and Interleaver . 36 6.2.12.1 S-CDMA Framing Considerations . 36 6.2.12.2 Mini-slot Numbering . 36 6.2.12.2.1 Mini-slot Numbering Parameters in UCD . 38 6.2.12.2.2 Mini-slot Numbering Examples . 39 6.2.12.3 Transmission Time . 40 6.2.12.4 Latency Considerations . 40 6.2.12.5 Spreader-off Bursts for Maintenance on S-CDMA channel . 40 6.2.12.6 Limiting the Number of Codes Assigned to a CM . 42 6.2.13 S-CDMA Framer . 42 6.2.13.1 Subframe Definition . 42 6.2.13.2 Framer Operation . 43 6.2.13.2.1 Rules for Preamble and Coded TCM Symbols . 43 6.2.13.2.2 Rules for Uncoded Symbols and the Uncoded TCM Subsymbols . 44 6.2.13.2.3 Subframe Example . 44 6.2.13.2.4 Frame Transmission . 45 6.2.14 Symbol Mapping . 45 6.2.15 S-CDMA Spreader . 51 6.2.15.1 Code Hopping . 52 6.2.15.1.1 Code Hopping Mode 1 . 53 6.2.15.1.2 Code Hopping Mode 2 . 53 6.2.15.1.3 Code hopping generator. 55 6.2.16 Transmit Pre-Equalizer . 57 6.2.17 Spectral Shaping . 59 6.2.17.1 Upstream Frequency Agility and Range . 59 6.2.17.2 Spectrum Format . 59 6.2.18 Relative Processing Delays . 59 6.2.19 Transmit Power Requirements . 60 6.2.19.1 TDMA Transmit Power Calculations. 64 6.2.19.2 S-CDMA Transmit Power Calculations . 65 6.2.19.2.1 S-CDMA Transmit Power Calculations when Maximum Scheduled Codes Is Not Enabled . 65 6.2.19.2.2 S-CDMA Transmit Power Calculations When Maximum Scheduled Codes is Enabled . 66 6.2.19.3 Transmit Power Step Size . 69 6.2.19.4 Transmit Power Requirements for Multiple Transmit Channel mode Not Enabled . 69 6.2.20 Burst Profiles . 70 6.2.20.1 Ranging Offset . 71 6.2.20.2 TDMA Reconfiguration Times . 72 6.2.20.3 S-CDMA Reconfiguration Time . 73 6.2.20.4 CM Timing Offsets When Changing Modulation Rate. 74 6.2.21 Burst Timing Convention . 75 6.2.22 Fidelity Requirements . 76 6.2.22.1 Spurious Emissions . 76 6.2.22.1.1 Adjacent Channel Spurious Emissions . 79 6.2.22.1.2 Spurious Emissions in the Upstream Frequency Range . 79 6.2.22.2 Spurious Emissions During Burst On/Off Transients . 80 6.2.22.3 Modulation Error Ratio (MER) . 80 6.2.22.3.1 Definitions . 80 6.2.22.3.2 Requirements . 81 6.2.22.4 Filter Distortion . 82 6.2.22.4.1 Amplitude . 82 6.2.22.5 Carrier Phase Noise . 83 6.2.22.6 Channel Frequency Accuracy . 83 6.2.22.7 Modulation Rate Accuracy . 83 6.2.22.8 Modulation Timing Jitter . 83 6.2.22.8.1 Symbol Timing Jitter for TDMA Upstream Channels in Asynchronous Operation . 83 6.2.22.8.2 Modulation Timing Jitter for Synchronous Operation . 84 6.2.23 Upstream Demodulator Input Power Characteristics . 84 6.2.24 Upstream Electrical Output from the CM . 85 6.2.25 Upstream CM Transmitter Capabilities . 86 6.2.25.1 Description of CM Upstream Transmit Channel Set Capability . 86 6.3 Downstream . 87 6.3.1 Downstream Protocol and Interleaving Support . 87 SIST EN 302 878-2 V1.1.1:2012
ETSI ETSI EN 302 878-2 V1.1.1 (2011-11) 5 6.3.2 Downstream Electrical Input to CM . 87 6.3.3 CM BER Performance . 87 6.3.3.1 64-QAM . 88 6.3.3.1.1 64-QAM CM BER Performance . 88 6.3.3.1.2 Image Rejection Performance . 88 6.3.3.1.3 64-QAM Adjacent Channel Performance. 88 6.3.3.2 256-QAM . 88 6.3.3.2.1 256-QAM CM BER Performance . 88 6.3.3.2.2 256-QAM Image Rejection Performance . 88 6.3.3.2.3 256-QAM Adjacent Channel Performance. 89 6.3.4 Downstream Multiple Receiver Capabilities . 89 6.3.4.1 Receive Module Parameters . 89 6.3.4.2 Receive Channel Parameters . 90 6.3.4.3 Standard Receive Channel Profile . 90 6.3.4.4 Example Manufacturer Receive Channel Profile . 91 6.3.4.5 Reconfiguration of CM Receive Channels . 92 6.3.5 Non-Synchronous DS Channel Support . 92 Annex A (normative): Timing Requirements for Supporting Business Services over DOCSIS . 93 A.1 CMTS . 93 A.2 CM . 93 Annex B (normative): Additions and Modifications for European Specification . 94 B.1 Scope . 94 B.1.1 Introduction and Purpose . 94 B.1.2 Background . 94 B.1.2.1 Broadband Access Network . 94 B.1.2.2 Network and System Architecture . 94 B.1.2.2.1 The DOCSIS Network . 94 B.1.2.3 Service Goals . 95 B.1.2.4 Statement of Compatibility . 95 B.1.2.5 Reference Architecture . 95 B.1.2.6 Void . 95 B.1.3 Requirements . 95 B.1.4 Conventions . 95 B.1.5 Void . 95 B.2 References . 95 B.2.1 Normative References . 95 B.2.2 Informative References . 95 B.2.3 Reference Acquisition . 95 B.3 Terms and Definitions . 95 B.4 Abbreviations and Acronyms . 96 B.5 Functional Assumptions . 96 B.5.1 Equipment Assumptions . 96 B.5.1.1 Frequency Plan . 96 B.5.1.2 Compatibility with Other Services . 96 B.5.1.3 Fault Isolation Impact on Other Users . 96 B.5.1.4 Cable System Terminal Devices . 96 B.5.2 RF Channel Assumptions . 96 B.5.2.1 Transmission Downstream . 97 B.5.2.2 Transmission Upstream . 98 B.5.2.2.1 Availability. 98 B.5.3 Transmission Levels . 98 B.5.4 Frequency Inversion . 98 B.6 Physical Media Dependent Sublayer Specification . 98 B.6.1 Scope . 98 SIST EN 302 878-2 V1.1.1:2012
ETSI ETSI EN 302 878-2 V1.1.1 (2011-11) 6 B.6.2 Upstream . 99 B.6.2.1 Overview . 99 B.6.2.2 Signal Processing Requirements . 100 B.6.2.3 Modulation Formats . 100 B.6.2.4 R-S Encode . 100 B.6.2.4.1 R-S Encode Modes .
...
SLOVENSKI STANDARD
oSIST prEN 302 878-2 V1.1.0:2011
01-junij-2011
'RVWRSSULNOMXþNLSUHQRVLQPXOWLSOHNVLUDQMH $770 7UHWMDJHQHUDFLMDSUHQRVQLK
VLVWHPRY]DVWRULWYHLQWHUDNWLYQHNDEHOVNHWHOHYL]LMH,3NDEHOVNLPRGHPLGHO
)L]LþQDSODVW'2&6,6
Access, Terminals, Transmission and Multiplexing (ATTM) - Third Generation
Transmission Systems for Interactive Cable Television Services - IP Cable Modems -
Part 2: Physical Layer - DOCSIS 3.0
Ta slovenski standard je istoveten z: EN 302 878-2 Version 1.1.0
ICS:
35.100.10 )L]LþQLVORM Physical layer
35.180 Terminalska in druga IT Terminal and other
periferna oprema IT peripheral equipment
oSIST prEN 302 878-2 V1.1.0:2011 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
oSIST prEN 302 878-2 V1.1.0:2011
---------------------- Page: 2 ----------------------
oSIST prEN 302 878-2 V1.1.0:2011
Draft ETSI EN 302 878-2 V1.1.0 (2011-04)
European Standard
Access, Terminals, Transmission and Multiplexing (ATTM);
Third Generation Transmission Systems for
Interactive Cable Television Services - IP Cable Modems;
Part 2: Physical Layer;
DOCSIS 3.0
---------------------- Page: 3 ----------------------
oSIST prEN 302 878-2 V1.1.0:2011
2 Draft ETSI EN 302 878-2 V1.1.0 (2011-04)
Reference
DEN/ATTM-003006-2
Keywords
access, broadband, cable, data, IP, IPCable,
modem
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
Individual copies of the present document can be downloaded from:
http://www.etsi.org
The present document may be made available in more than one electronic version or in print. In any case of existing or
perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF).
In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive
within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
http://portal.etsi.org/tb/status/status.asp
If you find errors in the present document, please send your comment to one of the following services:
http://portal.etsi.org/chaircor/ETSI_support.asp
Copyright Notification
No part may be reproduced except as authorized by written permission.
The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2011.
All rights reserved.
TM TM TM TM
DECT , PLUGTESTS , UMTS , TIPHON , the TIPHON logo and the ETSI logo are Trade Marks of ETSI registered
for the benefit of its Members.
TM
3GPP is a Trade Mark of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners.
LTE™ is a Trade Mark of ETSI currently being registered
for the benefit of its Members and of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI
---------------------- Page: 4 ----------------------
oSIST prEN 302 878-2 V1.1.0:2011
3 Draft ETSI EN 302 878-2 V1.1.0 (2011-04)
Contents
Intellectual Property Rights . 9
Foreword . 9
1 Scope . 10
1.1 Introduction and Purpose . 10
1.2 Requirements . 10
1.3 Conventions . 10
2 References . 11
2.1 Normative references . 11
2.2 Informative references . 12
3 Definitions and abbreviations . 12
3.1 Definitions . 12
3.2 Abbreviations . 18
4 Void . 20
5 Functional Assumptions . 20
5.1 Equipment Assumptions . 20
5.1.1 Frequency Plan . 20
5.1.2 Compatibility with Other Services . 20
5.1.3 Fault Isolation Impact on Other Users . 20
5.1.4 Cable System Terminal Devices . 21
5.2 RF Channel Assumptions . 21
5.2.1 Transmission Downstream . 21
5.2.2 Transmission Upstream . 21
5.2.2.1 Availability. 22
5.3 Transmission Levels . 22
5.4 Frequency Inversion . 22
6 Physical Media Dependent Sublayer Specification . 23
6.1 Scope . 23
6.2 Upstream . 23
6.2.1 Overview . 23
6.2.2 Signal Processing Requirements . 24
6.2.3 Modulation Formats . 26
6.2.4 R-S Encode . 27
6.2.4.1 R-S Encode Modes . 27
6.2.4.2 R-S Bit-to-Symbol Ordering . 27
6.2.5 Upstream R-S Frame Structure for DOCSIS 3.0 Multiple Transmit Channel mode Enabled . 27
6.2.5.1 R-S Codeword Length. 28
6.2.5.1.1 Burst Size . 28
6.2.5.1.2 Fixed Codeword Length . 28
6.2.5.1.3 Shortened Last Codeword . 29
6.2.5.2 R-S FEC Disabled . 29
6.2.6 Upstream R-S Frame Structure for DOCSIS 3.0 Multiple Transmit Channel mode Not Enabled . 29
6.2.7 TDMA Byte Interleaver . 29
6.2.7.1 Byte Interleaver Parameters . 29
6.2.7.2 Interleaver Operating Modes . 30
6.2.7.2.1 Fixed Mode . 30
6.2.7.2.2 Dynamic Mode . 31
6.2.8 Scrambler (Randomizer) . 32
6.2.9 TCM Encoder . 33
6.2.9.1 Byte to TCM Symbol Mapping . 33
6.2.10 Preamble Prepend . 35
6.2.11 Modulation Rates . 36
6.2.11.1 DOCSIS 3.0 Modulation Rates . 36
6.2.11.2 Backward Compatibility Modulation Rates . 36
ETSI
---------------------- Page: 5 ----------------------
oSIST prEN 302 878-2 V1.1.0:2011
4 Draft ETSI EN 302 878-2 V1.1.0 (2011-04)
6.2.12 S-CDMA Framer and Interleaver . 36
6.2.12.1 S-CDMA Framing Considerations . 36
6.2.12.2 Mini-slot Numbering . 36
6.2.12.2.1 Mini-slot Numbering Parameters in UCD . 38
6.2.12.2.2 Mini-slot Numbering Examples . 39
6.2.12.3 Transmission Time . 40
6.2.12.4 Latency Considerations . 40
6.2.12.5 Spreader-off Bursts for Maintenance on S-CDMA channel . 40
6.2.12.6 Limiting the Number of Codes Assigned to a CM . 42
6.2.13 S-CDMA Framer . 42
6.2.13.1 Subframe Definition . 42
6.2.13.2 Framer Operation . 43
6.2.13.2.1 Rules for Preamble and Coded TCM Symbols . 43
6.2.13.2.2 Rules for Uncoded Symbols and the Uncoded TCM Subsymbols . 44
6.2.13.2.3 Subframe Example . 44
6.2.13.2.4 Frame Transmission . 45
6.2.14 Symbol Mapping . 45
6.2.15 S-CDMA Spreader . 51
6.2.15.1 Code Hopping . 52
6.2.15.1.1 Code Hopping Mode 1 . 53
6.2.15.1.2 Code Hopping Mode 2 . 53
6.2.15.1.3 Code hopping generator. 55
6.2.16 Transmit Pre-Equalizer . 57
6.2.17 Spectral Shaping . 59
6.2.17.1 Upstream Frequency Agility and Range . 59
6.2.17.2 Spectrum Format . 59
6.2.18 Relative Processing Delays . 59
6.2.19 Transmit Power Requirements . 60
6.2.19.1 TDMA Transmit Power Calculations. 64
6.2.19.2 S-CDMA Transmit Power Calculations . 65
6.2.19.2.1 S-CDMA Transmit Power Calculations when Maximum Scheduled Codes Is Not Enabled . 65
6.2.19.2.2 S-CDMA Transmit Power Calculations When Maximum Scheduled Codes is Enabled . 66
6.2.19.3 Transmit Power Step Size . 69
6.2.19.4 Transmit Power Requirements for Multiple Transmit Channel mode Not Enabled . 69
6.2.20 Burst Profiles . 70
6.2.20.1 Ranging Offset . 71
6.2.20.2 TDMA Reconfiguration Times . 72
6.2.20.3 S-CDMA Reconfiguration Time . 73
6.2.20.4 CM Timing Offsets When Changing Modulation Rate. 74
6.2.21 Burst Timing Convention . 75
6.2.22 Fidelity Requirements . 76
6.2.22.1 Spurious Emissions . 76
6.2.22.1.1 Adjacent Channel Spurious Emissions . 79
6.2.22.1.2 Spurious Emissions in the Upstream Frequency Range . 79
6.2.22.2 Spurious Emissions During Burst On/Off Transients . 80
6.2.22.3 Modulation Error Ratio (MER) . 80
6.2.22.3.1 Definitions . 80
6.2.22.3.2 Requirements . 81
6.2.22.4 Filter Distortion . 82
6.2.22.4.1 Amplitude . 82
6.2.22.5 Carrier Phase Noise . 83
6.2.22.6 Channel Frequency Accuracy . 83
6.2.22.7 Modulation Rate Accuracy . 83
6.2.22.8 Modulation Timing Jitter . 83
6.2.22.8.1 Symbol Timing Jitter for TDMA Upstream Channels in Asynchronous Operation . 83
6.2.22.8.2 Modulation Timing Jitter for Synchronous Operation . 84
6.2.23 Upstream Demodulator Input Power Characteristics . 84
6.2.24 Upstream Electrical Output from the CM . 85
6.2.25 Upstream CM Transmitter Capabilities . 86
6.2.25.1 Description of CM Upstream Transmit Channel Set Capability . 86
6.3 Downstream . 87
6.3.1 Downstream Protocol and Interleaving Support . 87
ETSI
---------------------- Page: 6 ----------------------
oSIST prEN 302 878-2 V1.1.0:2011
5 Draft ETSI EN 302 878-2 V1.1.0 (2011-04)
6.3.2 Downstream Electrical Input to CM . 87
6.3.3 CM BER Performance . 87
6.3.3.1 64-QAM . 88
6.3.3.1.1 64-QAM CM BER Performance . 88
6.3.3.1.2 Image Rejection Performance . 88
6.3.3.1.3 64-QAM Adjacent Channel Performance. 88
6.3.3.2 256-QAM . 88
6.3.3.2.1 256-QAM CM BER Performance . 88
6.3.3.2.2 256-QAM Image Rejection Performance . 88
6.3.3.2.3 256-QAM Adjacent Channel Performance. 89
6.3.4 Downstream Multiple Receiver Capabilities . 89
6.3.4.1 Receive Module Parameters . 89
6.3.4.2 Receive Channel Parameters . 90
6.3.4.3 Standard Receive Channel Profile . 90
6.3.4.4 Example Manufacturer Receive Channel Profile . 91
6.3.4.5 Reconfiguration of CM Receive Channels . 92
6.3.5 Non-Synchronous DS Channel Support . 92
Annex A (normative): Timing Requirements for Supporting Business Services over DOCSIS . 93
A.1 CMTS . . 93
A.2 CM . . 93
Annex B (normative): Additions and Modifications for European Specification . 94
B.1 Scope . 94
B.1.1 Introduction and Purpose . 94
B.1.2 Background . 94
B.1.2.1 Broadband Access Network . 94
B.1.2.2 Network and System Architecture . 94
B.1.2.2.1 The DOCSIS Network . 94
B.1.2.3 Service Goals . 95
B.1.2.4 Statement of Compatibility . 95
B.1.2.5 Reference Architecture . 95
B.1.2.6 Void . 95
B.1.3 Requirements . 95
B.1.4 Conventions . 95
B.1.5 Organization of Document . 95
B.2 References . 95
B.2.1 Normative References . 95
B.2.2 Informative References . 95
B.2.3 Reference Acquisition . 95
B.3 Terms and Definitions . 95
B.4 Abbreviations and Acronyms . 96
B.5 Functional Assumptions . 96
B.5.1 Equipment Assumptions . 96
B.5.1.1 Frequency Plan . 96
B.5.1.2 Compatibility with Other Services . 96
B.5.1.3 Fault Isolation Impact on Other Users . 96
B.5.1.4 Cable System Terminal Devices . 96
B.5.2 RF Channel Assumptions . 96
B.5.2.1 Transmission Downstream . 97
B.5.2.2 Transmission Upstream . 98
B.5.2.2.1 Availability. 98
B.5.3 Transmission Levels . 98
B.5.4 Frequency Inversion . 98
B.6 Physical Media Dependent Sublayer Specification . 98
B.6.1 Scope . 98
B.6.2 Upstream .
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.