IEC 61978-1:2009
(Main)Fibre optic interconnecting devices and passive components - Fibre optic passive chromatic dispersion compensators - Part 1: Generic specification
Fibre optic interconnecting devices and passive components - Fibre optic passive chromatic dispersion compensators - Part 1: Generic specification
IEC 61978-1:2009 applies to fibre optic passive chromatic dispersion compensators, all exhibiting the following features:
- they are optically passive;
- they have an optical input and an optical output for transmitting optical power;
- they are wavelength sensitive;
- they may be polarization sensitive.
This standard establishes uniform requirements for the passive chromatic dispersion compensator. Changes from the previous edition of this standard are to reconsider the requirements.
Dispositifs d'interconnexion et composants passifs à fibres optiques - Compensateurs de dispersion chromatique passifs à fibres optiques - Partie 1: Spécification générique
La CEI 61978-1:2009 s'applique aux compensateurs de dispersion chromatique passifs à fibres optiques présentant les caractéristiques suivantes:
- ils sont passifs au niveau optique;
- ils possèdent une entrée optique et une sortie optique pour la transmission de la puissance optique;
- les portes sont des fibrres optiques ou des connecteurs optiques;
- ils sont sensibles aux longueurs d'onde;
- ils peuvent être sensibles à la polarisation.
La présente norme établit des exigences uniformes sur les compensateurs de dispersion chromatique passifs. Les changements par rapport à la première édition de cette norme consistent en la reconsidération des exigences.
General Information
Relations
Standards Content (Sample)
IEC 61978-1
®
Edition 2.0 2009-11
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
colour
inside
Fibre optic interconnecting devices and passive components – Fibre optic
passive chromatic dispersion compensators –
Part 1: Generic specification
Dispositifs d’interconnexion et composants passifs à fibres optiques –
Compensateurs de dispersion chromatique passifs à fibres optiques –
Partie 1: Spécification générique
IEC 61978-1:2009
---------------------- Page: 1 ----------------------
THIS PUBLICATION IS COPYRIGHT PROTECTED
Copyright © 2009 IEC, Geneva, Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by
any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either IEC or
IEC's member National Committee in the country of the requester.
If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publication,
please contact the address below or your local IEC member National Committee for further information.
Droits de reproduction réservés. Sauf indication contraire, aucune partie de cette publication ne peut être reproduite
ni utilisée sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie
et les microfilms, sans l'accord écrit de la CEI ou du Comité national de la CEI du pays du demandeur.
Si vous avez des questions sur le copyright de la CEI ou si vous désirez obtenir des droits supplémentaires sur cette
publication, utilisez les coordonnées ci-après ou contactez le Comité national de la CEI de votre pays de résidence.
IEC Central Office
3, rue de Varembé
CH-1211 Geneva 20
Switzerland
Email: inmail@iec.ch
Web: www.iec.ch
About the IEC
The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes
International Standards for all electrical, electronic and related technologies.
About IEC publications
The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the
latest edition, a corrigenda or an amendment might have been published.
ƒ Catalogue of IEC publications: www.iec.ch/searchpub
The IEC on-line Catalogue enables you to search by a variety of criteria (reference number, text, technical committee,…).
It also gives information on projects, withdrawn and replaced publications.
ƒ IEC Just Published: www.iec.ch/online_news/justpub
Stay up to date on all new IEC publications. Just Published details twice a month all new publications released. Available
on-line and also by email.
ƒ Electropedia: www.electropedia.org
The world's leading online dictionary of electronic and electrical terms containing more than 20 000 terms and definitions
in English and French, with equivalent terms in additional languages. Also known as the International Electrotechnical
Vocabulary online.
ƒ Customer Service Centre: www.iec.ch/webstore/custserv
If you wish to give us your feedback on this publication or need further assistance, please visit the Customer Service
Centre FAQ or contact us:
Email: csc@iec.ch
Tel.: +41 22 919 02 11
Fax: +41 22 919 03 00
A propos de la CEI
La Commission Electrotechnique Internationale (CEI) est la première organisation mondiale qui élabore et publie des
normes internationales pour tout ce qui a trait à l'électricité, à l'électronique et aux technologies apparentées.
A propos des publications CEI
Le contenu technique des publications de la CEI est constamment revu. Veuillez vous assurer que vous possédez
l’édition la plus récente, un corrigendum ou amendement peut avoir été publié.
ƒ Catalogue des publications de la CEI: www.iec.ch/searchpub/cur_fut-f.htm
Le Catalogue en-ligne de la CEI vous permet d’effectuer des recherches en utilisant différents critères (numéro de référence,
texte, comité d’études,…). Il donne aussi des informations sur les projets et les publications retirées ou remplacées.
ƒ Just Published CEI: www.iec.ch/online_news/justpub
Restez informé sur les nouvelles publications de la CEI. Just Published détaille deux fois par mois les nouvelles
publications parues. Disponible en-ligne et aussi par email.
ƒ Electropedia: www.electropedia.org
Le premier dictionnaire en ligne au monde de termes électroniques et électriques. Il contient plus de 20 000 termes et
définitions en anglais et en français, ainsi que les termes équivalents dans les langues additionnelles. Egalement appelé
Vocabulaire Electrotechnique International en ligne.
ƒ Service Clients: www.iec.ch/webstore/custserv/custserv_entry-f.htm
Si vous désirez nous donner des commentaires sur cette publication ou si vous avez des questions, visitez le FAQ du
Service clients ou contactez-nous:
Email: csc@iec.ch
Tél.: +41 22 919 02 11
Fax: +41 22 919 03 00
---------------------- Page: 2 ----------------------
IEC 61978-1
®
Edition 2.0 2009-11
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
colour
inside
Fibre optic interconnecting devices and passive components – Fibre optic
passive chromatic dispersion compensators –
Part 1: Generic specification
Dispositifs d’interconnexion et composants passifs à fibres optiques –
Compensateurs de dispersion chromatique passifs à fibres optiques –
Partie 1: Spécification générique
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
PRICE CODE
INTERNATIONALE
U
CODE PRIX
ICS 33.180.01 ISBN 978-2-88910-595-3
® Registered trademark of the International Electrotechnical Commission
Marque déposée de la Commission Electrotechnique Internationale
---------------------- Page: 3 ----------------------
– 2 – 61978-1 © IEC:2009
CONTENTS
FOREWORD.4
1 Scope.6
2 Normative references .6
3 Terms and definitions .7
3.1 Basic term .7
3.2 Component.7
3.3 Performance parameter.8
4 Requirements .10
4.1 General .10
4.2 Classification.10
4.2.1 Type.10
4.2.2 Style.11
4.2.3 Variant .12
4.2.4 Assessment level.12
4.2.5 Normative reference extensions .12
4.3 Documentation .13
4.3.1 Symbols .13
4.3.2 Specification system.13
4.3.3 Drawings .15
4.3.4 Tests and measurements.15
4.3.5 Test data sheets.16
4.3.6 Instructions for use.16
4.4 Standardization system .16
4.4.1 Performance standards.16
4.4.2 Reliability standards .16
4.4.3 Interlinking .17
4.5 Design and construction .18
4.5.1 Materials .18
4.5.2 Workmanship.19
4.6 Performance.19
4.7 Identification and marking .19
4.7.1 Variant identification number .19
4.7.2 Component marking .19
4.7.3 Package marking.20
4.8 Packaging .20
4.9 Storage conditions .20
4.10 Safety .20
Annex A (informative) Example of dispersion compensating technologies .21
Bibliography.27
Figure 1 – Standards currently under preparation .18
Figure A.1 – Chromatic dispersion in a standard single-mode optical fibre(SMF) .21
Figure A.2 – Calculated contour for different dispersion at the wavelength of 1,55 μm for a
step index core fibre .22
Figure A.3 – Examples of refractive index profile used in DCF .22
---------------------- Page: 4 ----------------------
61978-1 © IEC:2009 – 3 –
Figure A.4 – Illustration of the use of a chirped fibre Bragg grating for chromatic dispersion
compensation .23
Figure A.5 – Zoom over 10 nm of the insertion loss spectrum including the optical circulator
(Figure A.5 a)) and the group delay spectrum (Figure A.5 b)) of a multi-channel FBG tailored
for the compensation of the chromatic dispersion accumulated over 100 km of single-mode
fibre .24
Figure A.6 – Structure of virtually imaged phased array (VIPA).25
Figure A.7 – Detailed light path and mechanism of generating chromatic dispersion .25
Figure A.8 – Gires-Tournois interferometer .26
Table 1 – Types of passive chromatic dispersion compensators.11
Table 2 – Three-level IEC specification structure .14
Table 3 – Standards interlink matrix.18
Table 4 – Quality assurance options .18
---------------------- Page: 5 ----------------------
– 4 – 61978-1 © IEC:2009
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
FIBRE OPTIC INTERCONNECTING
DEVICES AND PASSIVE COMPONENTS –
FIBRE OPTIC PASSIVE CHROMATIC DISPERSION COMPENSATORS –
Part 1: Generic specification
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 61978-1 has been prepared by subcommittee 86B: Fibre optic
interconnecting devices and passive components, of IEC technical committee 86: Fibre optics.
This second edition cancels and replaces the first edition published in 2000. It constitutes a
technical revision. Changes from the previous edition of this standard are to reconsider the
requirements.
The text of this standard is based on the following documents:
FDIS Report on voting
86B/2908/FDIS 86B/2946/RVD
Full information on the voting for the approval of this standard can be found in the report on
voting indicated in the above table.
---------------------- Page: 6 ----------------------
61978-1 © IEC:2009 – 5 –
This publication has been drafted in accordance with the ISO/IEC Directives, Part 2.
The committee has decided that the contents of this publication will remain unchanged until
the maintenance result date indicated on the IEC web site under "http://webstore.iec.ch" in
the data related to the specific publication. At this date, the publication will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.
IMPORTANT – The “colour inside” logo on the cover page of this publication indicates
that it contains colours which are considered to be useful for the correct understanding
of its contents. Users should therefore print this publication using a colour printer.
---------------------- Page: 7 ----------------------
– 6 – 61978-1 © IEC:2009
FIBRE OPTIC INTERCONNECTING
DEVICES AND PASSIVE COMPONENTS –
FIBRE OPTIC PASSIVE CHROMATIC DISPERSION COMPENSATORS –
Part 1: Generic specification
1 Scope
This part of IEC 61978 applies to fibre optic passive chromatic dispersion compensators, all
exhibiting the following features:
– they are optically passive;
– they have an optical input and an optical output for transmitting optical power;
– the ports are optical fibres or optical fibre connectors;
– they are wavelength sensitive;
– they may be polarization sensitive.
This standard establishes uniform requirements for the passive chromatic dispersion
compensator.
2 Normative references
The following referenced documents are indispensable for the application of this document.
For dated references, only the edition cited applies. For undated references, the latest edition
of the referenced document (including any amendments) applies.
IEC 60027 (all parts), Letter symbols to be used in electrical technology
IEC 60050(731), International Electrotechnical Vocabulary (IEV) – Chapter 731: Optical fibre
communication
IEC 60617 (all parts), Graphical symbols for diagrams
IEC 60695-11-5, Fire hazard testing – Part 11-5: Test flames – Needle-flame test method –
Apparatus, confirmatory test arrangement and guidance
IEC 60793-2-50, Optical fibres – Part 2-50: Product specifications – Sectional specification for
class B single-mode fibres
IEC 60825 (all parts), Safety of laser products
IEC 60869-1, Fibre optic attenuators - Part 1: Generic specification
IEC 60874 (all parts), Connectors for optical fibres and cables
IEC 60974 (all parts), Arc welding equipment
IEC 61073-1, Fibre optic interconnecting devices and passive components – Mechanical
splices and fusion splice protectors for optical fibres and cables – Part 1: Generic
specification
---------------------- Page: 8 ----------------------
61978-1 © IEC:2009 – 7 –
IEC 61300 (all parts), Fibre optic interconnecting devices and passive components – Basic
test and measurement procedures
IEC 61754-4, Fibre optic connector interfaces – Part 4: Type SC connector family
IEC 61754-13, Fibre optic connector interfaces – Part 13: Type FC-PC connector
IEC 61754-15, Fibre optic connector interfaces – Part 15: Type LSH connector family
IEC/TR 61930, Fibre optic graphical symbology
IEC Guide 102, Electronic components — Specification structures for quality Assessment
(Qualification approval and capability approval)
IECQ 01, IEC Quality Assessment System for Electronic Components (IECQ System) Basic
Rules
IECQ QC 001002-3, IEC Quality Assessment System for Electronic Components (IECQ) –
Rules of Procedure – Part 3: Approval procedures
ISO 129-1, Technical drawings – Indication of dimensions and tolerances – Part 1: General
principles
ISO 286-1, ISO system of limits and fits – Part 1: Bases of tolerances, deviations and fits
ISO 1101, Geometrical Product Specifications (GPS) – Geometrical tolerancing -- Tolerances
of form, orientation, location and run-out
ISO 8601, Data elements and interchange formats – Information interchange –
Representation of dates and times
3 Terms and definitions
For the purposes of this document, the terms and definitions given in IEC 60050(731), as well
as the following definitions apply.
3.1 Basic term
3.1.1
port
optical fibre or optical fibre connector attached to a passive component for the entry and/or
exit of the optical power (input and/or output port)
3.2 Component
3.2.1
passive chromatic dispersion compensator
PCDC
two-port in-line passive device used to perform chromatic dispersion compensation. PCDCs
are commonly used to compensate the chromatic dispersion of an optical path by adding the
opposite sign chromatic dispersion. The typical optical paths are single-mode fibre, dispersion
shifted fibre and non-zero dispersion shifted fibre. PCDCs have either negative or positive
chromatic dispersion values depending on the chromatic dispersion sign of the optical path
---------------------- Page: 9 ----------------------
– 8 – 61978-1 © IEC:2009
3.2.2
dispersion compensating fibre
DCF
DCF is a speciality fibre to compensate chromatic dispersion of an optical path. By the control
of the refractive index profile of the fibre, DCF realises opposite sign chromatic dispersion
characteristics to that of the optical path
3.2.3
fibre Bragg grating
FBG
FBG is a fibre type optical device which has modulated refractive index profile in the core.
PCDC is realised by a chirped FBG which has gradually changed refractive index along the
fibre axis
3.2.4
virtually imaged phased array
VIPA
VIPA is an optical device which consists of coated glass plate, focusing lens and 3-
dimensional mirror. VIPA produces both positive and negative chromatic dispersion by the
move of the 3-dimensional mirror, in order to compensate the chromatic dispersion of an
optical path
3.2.5
etalon
etalon is an optical cavity which consists of a pair of parallel reflective mirror. PCDC is
realised by the etalon application called Gires-Tournois interferometer
3.3 Performance parameter
3.3.1
chromatic dispersion compensation
process by which a certain amount of chromatic dispersion is removed in order to mitigate the
system impairment caused by this excessive unwanted amount
3.3.2
group delay
time by which a pulse is delayed by an optical device. The group delay generally varies with
the operating wavelength
3.3.3
chromatic dispersion
derivative of group delay with respect to wavelength or frequency. A typical unit is ps/nm or
)
1
. The chromatic dispersion generally varies with the operating wavelength
ps/GHz
3.3.4
dispersion slope
derivative of chromatic dispersion with respect to wavelength or frequency. A typical unit is
2 1)
ps/nm or ps/GHz . The dispersion slope generally varies with the operating wavelength
3.3.5
operating wavelength
nominal wavelength λ at which a passive device operates with the specified performance
___________
1
Units of ps/GHz are generally considered as better definition, even though it is not widely used.
---------------------- Page: 10 ----------------------
61978-1 © IEC:2009 – 9 –
3.3.6
operating wavelength range
specified range of wavelengths from λ to λ about an operating wavelength λ, within
min max
which a passive component operates with the specified performance
3.3.7
figure of merit
FoM
ratio of the dispersion to the insertion loss of a PCDC at a particular operating wavelength
3.3.8
passband ripple
maximum peak-to-peak variation of insertion loss in the passband
3.3.9
group delay ripple
maximum peak-to-peak variation of group delay in the operating wavelength range
3.3.10
phase ripple
maximum peak-to-peak variation of optical phase in the operating wavelength range
3.3.11
insertion loss
reduction in optical power between an input and output port of a passive component
expressed in decibels. It is defined as follows:
P
a
a = −10log
P
0
where
P is the optical power launched into the input port;
0
P is the optical power received from the output port
a
3.3.12
return loss
fraction of input power that is returned from the input port of a passive component expressed
in decibels. It is defined as follows:
P
r
RL = −10log
P
0
where
P is the optical power launched into the input port;
0
P is the optical power received back from the same port
r
3.3.13
reflectance
negative of the return loss
3.3.14
polarization dependent loss
PDL
maximum variation of insertion loss due to a variation of the state of polarization (SOP) over
all the SOPs
---------------------- Page: 11 ----------------------
– 10 – 61978-1 © IEC:2009
3.3.15
wavelength dependent loss
WDL
maximum variation of the insertion loss over operating wavelength range
3.3.16
polarization mode dispersion
PMD
when an optical signal passes through an optical fibre, component or subsystem, the change
in the shape and width of the pulse due to the average delay of the travelling time between
the two principal states of polarization (PSP), differential group delay (DGD), and/or to the
waveform distortion for each PSP, is called PMD
NOTE PMD, together with polarization dependent loss (PDL) and polarization dependent gain (PDG), when
applicable, may introduce waveform distortion leading to unacceptable bit error rate increase.
4 Requirements
4.1 General
The requirements for PCDCs covered by this clause are intended to aid in classifying this
device in a relevant specification. Additional or more severe requirements may be imposed by
the relevant blank detail specification and by the detail specification.
4.2 Classification
PCDCs shall be classified as follows:
– type;
– style;
– variant;
– assessment level;
– normative reference extensions.
4.2.1 Type
PCDCs are divided into types by their main characteristics as follows.
PCDCs for WDM applications are divided into single channel type and multi-channel type.
Operating wavelength range of multi-channel type PCDCs covers at least two channels of
WDM systems. Multi-channel type PCDCs are divided into narrow band type and wide band
type according to its spectral characteristics:
– for TDM or for WDM;
– single channel or multi-channel;
– narrow or wide;
– any combination of the above.
---------------------- Page: 12 ----------------------
61978-1 © IEC:2009 – 11 –
Table 1 – Types of passive chromatic dispersion compensators
Operating
Applications Channel number Technologies
wavelength range
TDM Single channel Narrow Dispersion compensating fibre (DCF)
Fibre Bragg grating (FBG)
Etalon
WDM Single channel Narrow FBG
a)
Multi-channel Narrow FBG
Etalon
Virtually imaged phased array (VIPA)
Wide DCF
a
Can be used as fixed, although it has tuneable function.
Each type shall be applied to the following optical paths with negative or positive chromatic
dispersion:
– for single-mode fibre or for dispersion shifted fibre or for non-zero dispersion shifted fibre;
– to add negative chromatic dispersion to compensate the positive chromatic dispersion of
an optical path or to add positive chromatic dispersion to compensate the negative
chromatic dispersion of an optical path.
4.2.2 Style
PCDC may be classified into styles based on the fibre type(s), the connector type(s), cable
type(s), housing shape, temperature control and the configuration. Style is not intended to
define material or design. The configurations of PCDC ports are classified as follows.
4.2.2.1 Configuration A
A device containing integral fibre optic pigtails, without connectors.
PCDC
Pigtail
IEC 1687/2000
4.2.2.2 Configuration B
A device containing integral fibre optic pigtails, with a connector on each pigtail.
Connector
PCDC
Pigtail
IEC 1688/2000
4.2.2.3 Configuration C
A device containing fibre optic connectors as an integral part of the device housing.
---------------------- Page: 13 ----------------------
– 12 – 61978-1 © IEC:2009
Connector
PCDC
IEC 1689/2000
4.2.2.4 Configuration D
A device containing some combination of the interfacing features of the preceding configurations.
4.2.3 Variant
The PCDC variant identifies those common features which encompass structurally similar
components.
Examples of features which define a variant include, but are not limited to, the following:
– fibre type;
– connector type.
4.2.4 Assessment level
Detail specifications shall specify one or more assessment levels, each of which shall be
designated by a capital letter. The assessment level defines the relationship between the
inspection levels of groups A and B and the periodicity of inspection of groups C and D.
The following are the preferred levels.
Assessment level A:
– group A inspection: inspection level II, AQL = 4 %;
– group B inspection: inspection level II, AQL = 4 %;
– group C inspection: 24-month periods;
– group D inspection: 48-month periods.
Assessment level B:
– group A inspection: inspection level II, AQL = 1 %;
– group B inspection: inspection level II, AQL = 1 %;
– group C inspection: 18-month periods;
– group D inspection: 36-month periods.
Assessment level C:
– group A inspection: inspection level II, AQL = 0,4 %;
– group B inspection: inspecti
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.