IEC PAS 63077:2016

Good refurbishment practices for medical imaging equipment

IEC PAS 63077:2016(E) describes and defines the process of refurbishment of used medical imaging equipment and applies to the restoring of used medical imaging equipment to a condition of safety and effectiveness comparable to that of new equipment. This restoration includes actions such as repair, rework, software/hardware updates, and the replacement of worn parts with original parts. This document enumerates the actions that must be performed and the manner consistent with product specifications and service procedures required to ensure that the refurbishment of medical imaging equipment is done without changing the finished medical imaging equipment's performance, safety specifications, or intended use according to its original or applicable valid registration.

General Information

• Status: Replaced
• Publication Date: 15-Nov-2016
• ICS: 11.040.55 - Diagnostic equipment
• Technical Committee: SC 62B - Medical imaging equipment, software, and systems
• Current Stage: DELPUB - Deleted Publication
• Completion Date: 13-Nov-2019

Relations

• Revised: IEC 63077:2019 - Good refurbishment practices for medical imaging equipment
• Effective Date: 05-Sep-2023

Standards Content (Sample)

IEC PAS 63077 ®
Edition 1.0 2016-11
PUBLICLY AVAILABLE
SPECIFICATION
PRE-STANDARD
Good refurbishment practices for medical imaging equipment

All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form

or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from
either IEC or IEC's member National Committee in the country of the requester. If you have any questions about IEC
copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or

your local IEC member National Committee for further information.

IEC Central Office Tel.: [phone]
3, rue de Varembé Fax: [phone]

CH-1211 Geneva 20 [e-mail]
Switzerland www.iec.ch
About the IEC
The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes
International Standards for all electrical, electronic and related technologies.

About IEC publications
The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the
latest edition, a corrigenda or an amendment might have been published.

IEC Catalogue - webstore.iec.ch/catalogue Electropedia - www.electropedia.org
The stand-alone application for consulting the entire The world's leading online dictionary of electronic and
bibliographical information on IEC International Standards, electrical terms containing 20 000 terms and definitions in
Technical Specifications, Technical Reports and other English and French, with equivalent terms in 15 additional
documents. Available for PC, Mac OS, Android Tablets and languages. Also known as the International Electrotechnical
iPad. Vocabulary (IEV) online.

IEC publications search - www.iec.ch/searchpub IEC Glossary - std.iec.ch/glossary
The advanced search enables to find IEC publications by a 65 000 electrotechnical terminology entries in English and
variety of criteria (reference number, text, technical French extracted from the Terms and Definitions clause of
committee,…). It also gives information on projects, replaced IEC publications issued since 2002. Some entries have been
and withdrawn publications. collected from earlier publications of IEC TC 37, 77, 86 and

CISPR.
IEC Just Published - webstore.iec.ch/justpublished

Stay up to date on all new IEC publications. Just Published IEC Customer Service Centre - webstore.iec.ch/csc
details all new publications released. Available online and If you wish to give us your feedback on this publication or
also once a month by email. need further assistance, please contact the Customer Service
Centre: [e-mail].
IEC PAS 63077 ®
Edition 1.0 2016-11
PUBLICLY AVAILABLE
SPECIFICATION
PRE-STANDARD
Good refurbishment practices for medical imaging equipment

INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
ICS 11.040.55 ISBN 978-2-8322-3761-8

– 2 – IEC PAS 63077:2016 © IEC 2016

CONTENTS
FOREWORD . 3

INTRODUCTION . 5

1 Scope . 6

2 Normative references . 6

3 Terms and definitions . 6

4 General requirements for refurbishment of used medical devices . 8

4.1 Quality management system . 8
4.2 Resource management . 8
4.3 Corrective and preventive action . 9
4.4 Customer complaints . 9
4.5 Production and service provision . 9
4.6 Control of non-conforming product . 9
4.7 Post-market surveillance process . 9
4.8 Document control . 9
4.9 Purchasing . 9
4.10 Control of design and design changes . 10
4.11 Risk management process . 10
5 Specific requirements for good refurbishment practice . 10
5.1 General . 10
5.2 Selection of medical imaging equipment for refurbishment . 10
5.3 Evaluating market access requirements . 10
5.4 Preparation for refurbishment, disassembly, packing, and shipment . 10
5.5 Planning . 11
5.6 Installation of safety updates (hardware/software) . 11
5.7 Performance and safety test . 11
5.8 Packing, shipment, and installation of refurbished medical imaging
equipment . 11
5.9 Record of refurbishment . 11
5.10 Refurbishment label . 11
Bibliography . 12

INTERNATIONAL ELECTROTECHNICAL COMMISSION

____________
GOOD REFURBISHMENT PRACTICES
FOR MEDICAL IMAGING EQUIPMENT
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising

all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
A PAS is a technical specification not fulfilling the requirements for a standard, but made

available to the public.
IEC PAS 63077 has been processed by subcommittee 62B: Diagnostic imaging equipment, of
IEC technical committee 62: Electrical equipment in medical practice.
The text of this PAS is based on the This PAS was approved for
following document: publication by the P-members of the
committee concerned as indicated in
the following document
Draft PAS Report on voting
62B/1022/PAS 62B/1030/RVC
Following publication of this PAS, which is a pre-standard publication, the technical committee
or subcommittee concerned may transform it into an International Standard.

– 4 – IEC PAS 63077:2016 © IEC 2016

This PAS shall remain valid for an initial maximum period of 3 years starting from the

publication date. The validity may be extended for a single period up to a maximum of

3 years, at the end of which it shall be published as another type of normative document, or

shall be withdrawn.
INTRODUCTION
Keeping up with the latest innovations in medical technology often involves replacing

equipment in medical practice before it reaches the end of its expected service life. This is

because innovation cycles for medical technology are much shorter than the functional

lifecycle of capital equipment. As a result, a sustainable resource management model is

required: early replacement of installed medical imaging equipment by newer technology is

more economically feasible if the residual value of the existing medical imaging equipment is

utilized.
Conserving assets is a fundamental principle of ecological thinking in a recycling economy.

Several medical imaging equipment companies have already set up quality management
systems to refurbish used medical imaging equipment and have delivered this refurbished
equipment across the healthcare sector for many years. Refurbishment addresses the high
demand for affordable and reliable products. Customers of this used equipment are not only
small hospitals with limited budgets but also leading medical institutes. The EU and the US
represent by far the two largest markets for refurbished medical equipment. Refurbishment of
used medical imaging equipment is a well-established element of the healthcare economy.
If used medical imaging equipment is not accurately maintained according to requirements
defined by the manufacturer, it may result in additional risk for patients and operators.
Consequently, some countries have imposed bans on the importation of used medical imaging
equipment to protect public health. These bans fail to distinguish between quality-assured
refurbished medical imaging equipment and second-hand medical imaging equipment of
undefined quality, with the effect that patients may be denied access to the safe and
economical medical imaging equipment they need.
Safety and effectiveness are the most important aspects to consider with medical imaging
equipment, including used equipment. To ensure safety and effectiveness, used medical
imaging equipment has to be refurbished in a highly specialized and quality-assured way.

– 6 – IEC PAS 63077:2016 © IEC 2016

GOOD REFURBISHMENT PRACTICES
FOR MEDICAL IMAGING EQUIPMENT
1 Scope
This document describes and defines the process of refurbishment of used medical imaging
equipment and applies to the restoring of used medical imaging equipment to a condition of

safety and effectiveness comparable to that of new equipment. This restoration includes

actions such as repair, rework, software/hardware updates, and the replacement of worn parts
with original parts. This document enumerates the actions that must be performed and the
manner consistent with product specifications and service procedures required to ensure that
the refurbishment of medical imaging equipment is done without changing the finished
medical imaging equipment’s performa
...