IEC 60335-2-48:1995/AMD2:1998
(Amendment)Amendment 2 - Safety of household and similar electrical appliances - Part 2-48: Particular requirements for commercial electric grillers and toasters
Amendment 2 - Safety of household and similar electrical appliances - Part 2-48: Particular requirements for commercial electric grillers and toasters
General Information
Relations
Buy Standard
Standards Content (Sample)
INTERNATIONAL
IEC
STANDARD
60335-2-48
AMENDMENT 2
1998-11
Amendment 2
Safety of household and similar electrical
appliances –
Part 2-48:
Particular requirements for commercial
electric grillers and toasters
Amendement 2
Sécurité des appareils electrodomestiques et analogues –
Partie 2-48:
Règles particulières pour les grils et grille-pain
électriques à usage collectif
IEC 1998 Copyright - all rights reserved
International Electrotechnical Commission 3, rue de Varembé Geneva, Switzerland
Telefax: +41 22 919 0300 e-mail: inmail@iec.ch IEC web site http://www.iec.ch
Commission Electrotechnique Internationale
PRICE CODE
C
International Electrotechnical Commission
For price, see current catalogue
– 2 – 60335-2-48 amend. 2 © IEC:1998(E)
FOREWORD
This amendment has been prepared by subcommittee 61E: Safety of electrical commercial
catering equipment, of IEC technical committee 61: Safety of household and similar electrical
appliances.
The text of this amendment is based on the following documents:
FDIS Report on voting
61E/280/FDIS 61E/298/RVD
Full information on the voting for the approval of this amendment can be found in the report on
voting indicated in the above table.
___________
Page 13
7 Marking and instructions
Add the following text:
7.12.4 Addition:
The instructions for built-in appliances having a separate control panel for several appliances
shall state that the control panel is only to be connected to the specified appliances in order to
avoid a possible hazard.
Add the following text:
7.15 Addition:
When it is not practical to place the marking of fixed appliances so that it is visible after the
appliance has been installed, the relevant information shall also be included in the instructions
for use or on an additional label which can be fixed near the appliance after installation.
NOTE – An example of such a fixed appliance is a built-in appliance.
Replace, on page 15, subclause 7.101 by the following:
7.101 If,
...
This May Also Interest You
IEC 60335-2-60:2023 deals with the safety of electric whirlpool baths for indoor use and whirlpool spas, for household and similar use, their rated voltage being not more than 250 V for single-phase appliances and 480 V for other appliances, including direct current (DC) supplied appliances and battery-operated appliances. This standard also applies to appliances for circulating air or water in conventional baths. This standard applies to factory-built self-contained whirlpool baths or whirlpool spas in which all controls and components are integral parts of the appliance and are located within or affixed to the whirlpool bath or whirlpool spa structure. Appliances not intended for normal household use but that nevertheless can be a source of danger to the public, such as appliances intended to be used by laymen in hotels, fitness centres and similar places, are within the scope of this standard. As far as is practicable, this standard deals with the common hazards presented by appliances that are encountered by all persons in and around the home. However, in general, it does not take into account:
- persons (including children) whose physical, sensory or mental capabilities; or lack of experience and knowledge prevents them from using the appliance safely without supervision or instruction;
- children playing with the appliance.
Attention is drawn to the fact that
- for appliances intended to be used in vehicles or on board ships or aircraft, additional requirements can be necessary;
- in many countries additional requirements are specified by the national health authorities, the national water supply authorities, the national authorities responsible for the protection of labour and similar authorities.
This standard does not apply to
- equipment for water circulation in swimming and motion exercise pools;
- cleaning appliances for swimming pools;
- appliances intended for medical purposes (IEC 60601 series);
- field-engineered, non-self-contained permanently installed whirlpool baths or whirlpool spas custom designed to fit a specific location, being assembled or constructed at the final installation location;
- appliances intended to be used in locations where special conditions prevail, such as the presence of a corrosive or explosive atmosphere (dust, vapour or gas).
This fifth edition cancels and replaces the fourth edition published in 2017. This edition constitutes a technical revision.
This edition includes the following significant technical changes with respect to the previous edition:
a) alignment with IEC 60335-1:2020;
b) conversion of some notes to normative text (Clause 1, 7.12.1);
c) addition of hyperthermia instructions and installation instructions related to the wiring rules (7.12, 7.12.1);
d) modifications related to IEC 60364-7-702 and transportable whirlpool spas (Clause 1, 5.101, 6.1, 6.2, 7.12.1, 7.15, 13.1, 13.2, 16.1, 16.2, 22.33, 22.107, 25.1);
e) introduction of surface temperature limits (Clause 11);
f) addition of water temperature limit at the suction/return openings (11.8, 11.101);
g) modification to the tests of 19.2 and 19.3 specifying the types of devices that are rendered inoperative.
h) addition of requirement for thermal cut-outs to be trip free (24.101).
This part 2 is to be used in conjunction with the latest edition of IEC 60335-1 and its amendments unless that edition precludes it; in that case, the latest edition that does not preclude it is used. It was established on the basis of the sixth edition (2020) of that standard.
- Standard71 pagesEnglish languagesale 15% off
- Standard259 pagesEnglish languagesale 15% off
- Standard45 pagesEnglish and French languagesale 15% off
IEC 60335-2-109:2023 is available as IEC 60335-2-109:2023 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.IEC 60335-2-109:2023 deals with the safety of UV radiation water treatment appliances for household and similar use, their rated voltage being not more than 250 V for single-phase appliances and 480 V for other appliances including direct current (DC) supplied appliances and battery-operated appliances. Appliances not intended for normal household use but that nevertheless can be a source of danger to the public, such as appliances intended to be used by laymen in shops and in light industry and farms, are within the scope of this standard.
As far as is practicable, this standard deals with the common hazards presented by appliances that are encountered by all persons in and around the home. However, in general, it does not take into account
- persons (including children) whose physical, sensory or mental capabilities; or lack of experience and knowledge prevents them from using the appliance safely without supervision or instruction;
- children playing with the appliance.
Attention is drawn to the fact that
- for appliances intended to be used in vehicles or on board ships or aircraft, additional requirements can be necessary;
- in many countries, additional requirements are specified by the national health authorities, the national authorities responsible for the protection of labour and similar authorities.
This standard does not apply to
- pumps (IEC 60335-2-41);
- luminaires for aquariums (IEC 60598-2-11);
- luminaires for swimming pools and similar applications (IEC 60598-2-18);
- appliances intended exclusively for professional use;
- appliances intended to be used in locations where special conditions prevail, such as the presence of a corrosive or explosive atmosphere (dust, vapour or gas).
This second edition cancels and replaces the first edition published in 2010, Amendment 1:2013 and Amendment 2:2016. This edition constitutes a technical revision.
This edition includes the following significant technical changes with respect to the previous edition:
a) alignment with IEC 60335-1:2020;
b) modification or conversion of some notes to normative text (Clause 1, 6.2, 22.102);
c) introduction of IEC 60417 symbol for maximum operating depth (7.1, 7.6, 7.12.1);
d) addition of external accessible surface temperature limits (11.3, 11.8);
e) clarification of requirements for remote operation (22.40, 22.49, 22.51);
f) the requirements to emit harmful radiation are deleted, because they are covered in Part 1 (Clause 32).
This part 2 is to be used in conjunction with the latest edition of IEC 60335-1 and its amendments unless that edition precludes it; in that case, the latest edition that does not preclude it is used. It was established on the basis of the sixth edition (2020) of that standard.
- Standard56 pagesEnglish languagesale 15% off
- Standard249 pagesEnglish languagesale 15% off
- Standard39 pagesEnglish and French languagesale 15% off
IEC 60335-2-98:2023 is available as IEC 60335-2-98:2023 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.IEC 60335-2-98:2023 deals with the safety of electric humidifiers for household and similar use, their rated voltage being not more than 250 V for single-phase appliances and 480 V for other appliances, including direct current (DC) supplied appliances and battery-operated appliances.
Examples of appliances that are within the scope of the standard are
- appliances that atomize water;
- appliances that evaporate water by heating;
- appliances that blow air through a moist element.
Appliances that are not intended for normal household use, but that nevertheless can be a source of danger to the public, such as appliances intended to be used by laymen in shops, in light industry and on farms, are within the scope of this standard.
As far as is practicable, this standard deals with the common hazards presented by appliances that are encountered by all persons in and around the home. However, in general, it does not take into account
- persons (including children) whose physical, sensory or mental capabilities; or lack of experience and knowledge prevents them from using the appliance safely without supervision or instruction;
- children playing with the appliance.
Attention is drawn to the fact that
- for appliances intended to be used in vehicles or on board ships or aircraft, additional requirements can be necessary;
- in many countries additional requirements are specified by the national health authorities, the national authorities responsible for the protection of labour and similar authorities.
This standard does not apply to
- appliances for heating liquids (IEC 60335-2-15);
- humidifiers intended for use with heating, ventilation or air-conditioning systems (IEC 60335-2-88);
- appliances for medical purposes (IEC 60601 series);
- appliances intended exclusively for industrial purposes;
- appliances intended to be used in locations where special conditions prevail, such as the presence of a corrosive or explosive atmosphere (dust, vapour or gas).
This third edition cancels and replaces the second edition published in 2002, Amendment 1:2004 and Amendment 2:2008. This edition constitutes a technical revision.
This edition includes the following significant technical changes with respect to the previous edition:
a) alignment with IEC 60335-1:2020;
b) additional requirements for a humidifier shaped or decorated like a toy (7.12, 8.1.1, 21.101, 22.12, 22.44, 22.54, 22.105);
c) additional requirements are included for the temperature of accessible surfaces (11.8);
d) application of test probes 18 and 19 has been introduced (Clause 8, 20.2, B.22.3, B.22.4);
e) additional guidance is provided for humidifiers for remote operation.
This part 2 is to be used in conjunction with the latest edition of IEC 60335-1 and its amendments unless that edition precludes it; in that case, the latest edition that does not preclude it is used. It was established on the basis of the sixth edition (2020) of that standard.
- Standard64 pagesEnglish languagesale 15% off
- Standard255 pagesEnglish languagesale 15% off
- Standard43 pagesEnglish and French languagesale 15% off
- Standard1 pageEnglish languagesale 15% off
- Standard1 pageEnglish languagesale 15% off
IEC 60335-2-49:2021 is available as IEC 60335-2-49:2021 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.
IEC 60335-2-49:2021 deals with the safety of electrically operated commercial appliances for keeping food and crockery warm, their rated voltage being not more than 250 V for single-phase appliances connected between one phase and neutral, and 480 V for other appliances.
Examples of appliances that are within the scope of this standard are:
– hot cupboards, with or without heated tops;
– heated tops;
– heated display cases;
– heated crockery dispensers;
– heated tables;
– radiant heaters.
These appliances are not intended for household and similar purposes. They are used for commercial purposes, processing of food, also in areas open to the public, for example in kitchens of restaurants, canteens, hospitals and in commercial enterprises, such as bakeries and butcheries.
The electrical part of appliances making use of other forms of energy is also within the scope of this standard.
As far as is practicable, this standard deals with the common hazards presented by these types of appliances.
Attention is drawn to the fact that:
– for appliances intended to be used in vehicles or on board ships or aircraft, additional requirements can be necessary;
– in many countries, additional requirements are specified by the national health authorities, the national authorities responsible for the protection of labour, the national water supply authorities and similar authorities;
– in many countries, additional requirements are specified for pressure appliances.
This standard does not apply to:
– appliances designed exclusively for industrial purposes;
– appliances intended to be used in locations where special conditions prevail, such as the presence of a corrosive or explosive atmosphere (dust, vapour or gas);
– appliances for continuous mass production of food;
– commercial electric bains-marie (IEC 60335-2-50);
– battery-operated appliances;
– warming plates and similar appliances for household use covered by IEC 60335-2-12 used in the following environments by laymen: staff kitchen areas in shops, offices and other working environments, farm houses, hotels, motels and other residential type environments, bed and breakfast type environments.
This fifth edition cancels and replaces the fourth edition published in 2002, Amendment 1:2008 and Amendment 2:2017. This edition constitutes a technical revision.
This edition includes the following significant technical changes with respect to the previous edition:
a) the text has been aligned with IEC 60335-1:2020;
b) introduction of requirements for appliances intended for use in areas open to the public, including external accessible surface temperatures (Clause 1, 7.12, 11.8, Table 102);
c) exclusion of battery-operated appliances (Clause 1);
d) clarification of applicable standard for appliances for use by laymen (Clause 1, 7.12);
e) relocation of cleaning instructions from 7.12.1 to 7.12;
f) relocation of 24.101 to 22.106;
g) conciliation of the text of IEC 60335-2-49 with other standards under IEC/TC61/MT32;
h) some notes have been converted to normative text, modified or deleted (Clause 1, 7.1, 7.15, 11.3, 11.7, 15.2, 19.2, 22.101, 23.3);
i) additional requirements for measurement of input current;
j) clarification of the testing procedure in 15.1.1;
k) clarification of the test conditions in 20.1 and 23.3;
l) clarifications of the requirements in 25.3.
This Part 2 is to be used in conjunction with the latest edition of IEC 60335-1 and its amendments unless that edition precludes it; in that case, the latest edition that does not preclude it is used. It was established on the basis of the sixth edition (2020) of that standard.
- Standard110 pagesEnglish languagesale 15% off
- Standard71 pagesEnglish and French languagesale 15% off
IEC 60335-2-119:2021 deals with the safety of commercial electric packaging appliances using vacuum conditions for food preservation, their rated voltage being not more than 250 V for single-phase appliances and 480 V for other appliances.
These appliances are not intended for household and similar purposes. They are used for commercial preservation of food in areas not open to the public, for example in kitchens of restaurants, canteens, hospitals and in commercial enterprises such as bakeries and butcheries.
Examples of appliances that are within the scope of this standard are:
– chamber vacuum packaging appliances;
– vacuum packaging appliances.
These appliances may be provided with a film-sealing function.
This standard also deals with the hygiene aspects of appliances.
As far as is practicable, this standard deals with the common hazards presented by appliances that are encountered by users. However, in general, it does not consider young children playing with the appliance.
Attention is drawn to the fact that:
– for appliances intended to be used in vehicles or onboard ships or aircraft, additional requirements may be necessary;
– in many countries, additional requirements for appliances incorporating pressure vessels are specified;
– in many countries, additional requirements are specified by the national health authorities, the national authorities responsible for the protection of labour, the national water supply authorities and similar authorities.
This standard does not apply to:
– appliances which operate with injection in the vacuum chamber of inert gas with an oxygen content exceeding 21 %;
– appliances intended to be used in locations where special conditions prevail, such as the presence of a corrosive or explosive atmosphere (dust, vapour or gas);
– vacuum packaging appliances for household and similar use (IEC 60335-2-45);
– battery-operated appliances.
This Part 2 is to be used in conjunction with the latest edition of IEC 60335-1 and its amendments unless that edition precludes it; in that case, the latest edition that does not preclude it is used. It was established on the basis of the sixth edition (2020) of that standard.
- Standard42 pagesEnglish and French languagesale 15% off
IEC 60335-1:2020 deals with the safety of electrical appliances for household and similar purposes, their rated voltage being not more than 250 V for single-phase appliances and 480 V for other appliances including direct current (DC) supplied appliances and battery-operated appliances.
Appliances not intended for normal household use but which nevertheless may be a source of danger to the public, such as appliances intended to be used by laymen in shops, in light industry and on farms, are within the scope of this standard.
This standard deals with the reasonably foreseeable hazards presented by appliances that are encountered by all persons. However, in general, it does not take into account:
– persons (including children) whose physical, sensory or mental capabilities, or lack of experience and knowledge prevents them from using the appliance safely without supervision or instruction;
– children playing with the appliance.
Additional requirements may be necessary for appliances intended to be used in vehicles or on board ships or aircraft. In many countries, additional requirements are specified by the national health authorities, the national authorities responsible for the protection of labour, the national water supply authorities and similar authorities.
This standard does not apply to:
– appliances intended exclusively for industrial purposes;
– appliances intended to be used in locations where special conditions prevail, such as the presence of a corrosive or explosive atmosphere (dust, vapour or gas);
– audio, video and similar electronic apparatus (IEC 60065);
– medical electrical equipment (IEC 60601 series);
– hand-held motor-operated electric tools (IEC 60745 series);
– information technology equipment (IEC 60950-1);
– transportable motor-operated electric tools (IEC 61029 series);
– audio/video, information and communication technology equipment (IEC 62368-1);
– electric motor-operated hand-held tools, transportable tools and lawn and garden machinery (IEC 62841 series).
This sixth edition cancels and replaces the fifth edition published in 2010, Amendment 1: 2013 and Amendment 2:2016. This edition constitutes a technical revision.
This edition includes the following significant technical changes with respect to the previous edition (minor changes are not listed):
a) updated the text of this standard to align with the most recent editions of the dated normative references;
b) deleted some notes and converted many other notes, in whole or in part, to normative text;
c) changed some Annex designations from normative to informative;
d) introduced information on Guidance documents concerning the application of the safety requirements covered by IEC 60335 series and on how to retrieve them;
e) clarified requirements for PELV circuits;
f) clarification of requirements on measurement of power input and rated current when they vary throughout the operating cycle;
g) replaced normative Annex S with the informative Annex S "Guidance for the application of this standard on measurement of power input and current based on the requirements of 10.1 and 10.2 concerning the representative period";
h) introduced and clarified mechanical strength requirements for appliances with integral pins for insertion into socket-outlets;
i) revised requirements for battery-operated appliances;
j) introduced requirements for metal-ion batteries including a new Clause 12 Charging of metal-ion batteries;
k) introduced the application of test probe 18;
l) introduced requirements for appliances incorporating appliance outlets and socket-outlets accessible to the user;
m) revised and clarified requirements for appliances incorporating a functional earth;
n) introduced moisture resistance test requirements for appliances that incorporate an automatic cord reel and that have a second numeral IP rating;
o) clarified the appliance test criteria for the moisture resistance for appliances and parts of appliances with inte
- Standard210 pagesEnglish languagesale 15% off
- Standard440 pagesEnglish languagesale 15% off
- Standard434 pagesEnglish and French languagesale 15% off
- Standard4 pagesEnglish and French languagesale 15% off
Applies to liquid crystal and solid-state display modules such as the following:[
]- static/segment type liquid crystal display modules; - passive matrix monochrome and colour liquid crystal display modules; - active matrix monochrome and colour liquid crystal display modules.[
]Gives details of the quality assessment procedures, the inspection requirements, screening sequences, sampling requirements, and test and measurement procedures required for the assessment of liquid crystal display modules.
- Standard22 pagesEnglish and French languagesale 15% off
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.