IEC 60172:1987/AMD2:2010

Amendment 2 - Test procedure for the determination of the temperature index of enamelled winding wires

Amendement 2 - Méthode d'essai pour la détermination de l'indice de température des fils de bobinage émaillés

General Information

• Status: Published
• Publication Date: 06-Jan-2010
• ICS: 29.060.10 - Wires
• Technical Committee: TC 55 - Winding wires
• Drafting Committee: WG 1 - TC 55/WG 1
• Current Stage: DELPUB - Deleted Publication
• Completion Date: 12-May-2015

Relations

• Revised: IEC 60172:2015 - Test procedure for the determination of the temperature index of enamelled and tape wrapped winding wires
• Effective Date: 05-Sep-2023

Standards Content (Sample)

IEC 60172 ®
Edition 3.0 2010-01
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
AMENDMENT 2
AMENDEMENT 2
Test procedure for the determination of the temperature index of enamelled
winding wires
Méthode d'essai pour la détermination de l'indice de température des fils de
bobinage émaillés
IEC 60172:1987/A2:2010
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by
any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either IEC or
IEC's member National Committee in the country of the requester.
If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publication,
please contact the address below or your local IEC member National Committee for further information.

Droits de reproduction réservés. Sauf indication contraire, aucune partie de cette publication ne peut être reproduite
ni utilisée sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie
et les microfilms, sans l'accord écrit de la CEI ou du Comité national de la CEI du pays du demandeur.
Si vous avez des questions sur le copyright de la CEI ou si vous désirez obtenir des droits supplémentaires sur cette
publication, utilisez les coordonnées ci-après ou contactez le Comité national de la CEI de votre pays de résidence.

IEC Central Office
3, rue de Varembé
CH-1211 Geneva 20
Switzerland
Email: [e-mail]
Web: www.iec.ch
About the IEC
The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes
International Standards for all electrical, electronic and related technologies.

About IEC publications
The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the
latest edition, a corrigenda or an amendment might have been published.
ƒ Catalogue of IEC publications: www.iec.ch/searchpub
The IEC on-line Catalogue enables you to search by a variety of criteria (reference number, text, technical committee,…).
It also gives information on projects, withdrawn and replaced publications.
ƒ IEC Just Published: www.iec.ch/online_news/justpub
Stay up to date on all new IEC publications. Just Published details twice a month all new publications released. Available
on-line and also by email.
ƒ Electropedia: www.electropedia.org
The world's leading online dictionary of electronic and electrical terms containing more than 20 000 terms and definitions
in English and French, with equivalent terms in additional languages. Also known as the International Electrotechnical
Vocabulary online.
ƒ Customer Service Centre: www.iec.ch/webstore/custserv
If you wish to give us your feedback on this publication or need further assistance, please visit the Customer Service
Centre FAQ or contact us:
Email: [e-mail]
Tel.: [phone]
Fax: [phone]
A propos de la CEI
La Commission Electrotechnique Internationale (CEI) est la première organisation mondiale qui élabore et publie des
normes internationales pour tout ce qui a trait à l'électricité, à l'électronique et aux technologies apparentées.

A propos des publications CEI
Le contenu technique des publications de la CEI est constamment revu. Veuillez vous assurer que vous possédez
l’édition la plus récente, un corrigendum ou amendement peut avoir été publié.
ƒ Catalogue des publications de la CEI: www.iec.ch/searchpub/cur_fut-f.htm
Le Catalogue en-ligne de la CEI vous permet d’effectuer des recherches en utilisant différents critères (numéro de référence,
texte, comité d’études,…). Il donne aussi des informations sur les projets et les publications retirées ou remplacées.
ƒ Just Published CEI: www.iec.ch/online_news/justpub
Restez informé sur les nouvelles publications de la CEI. Just Published détaille deux fois par mois les nouvelles
publications parues. Disponible en-ligne et aussi par email.
ƒ Electropedia: www.electropedia.org
Le premier dictionnaire en ligne au monde de termes électroniques et électriques. Il contient plus de 20 000 termes et
définitions en anglais et en français, ainsi que les termes équivalents dans les langues additionnelles. Egalement appelé
Vocabulaire Electrotechnique International en ligne.
ƒ Service Clients: www.iec.ch/webstore/custserv/custserv_entry-f.htm
Si vous désirez nous donner des commentaires sur cette publication ou si vous avez des questions, visitez le FAQ du
Service clients ou contactez-nous:
Email: [e-mail]
Tél.: [phone]
Fax: [phone]
IEC 60172 ®
Edition 3.0 2010-01
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
AMENDMENT 2
AMENDEMENT 2
Test procedure for the determination of the temperature index of enamelled
winding wires
Méthode d'essai pour la détermination de l'indice de température des fils de
bobinage émaillés
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
PRICE CODE
INTERNATIONALE
F
CODE PRIX
ICS 29.060.10 ISBN 978-2-88910-062-0
– 2 – 60172 Amend. 2 © IEC:2010
FOREWORD
This amendment has been prepared by IEC technical committee 55: Winding wires.
The text of this amendment is based on the following documents:
CDV Report on voting
55/1140/CDV 55/1174/RVC
Full information on the voting for the approval of this amendment can be found in the report on
voting indicated in the above table.
The committee has decided that the contents of this amendment and the base publication will
remain unchanged until the maintenance result date indicated on the IEC web site under
"http://webstore.iec.ch" in the data related to the specific publication. At this date, the
publication will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.
_____________
5 Test specimens
5.1.1 Enamelled round wire with a nominal conductor diameter of 0,800 mm up to and
including 1,500 mm
Replace the title and text of this subclause by the following:
5.1.1 Enamelled round wire with a nominal conductor diameter of 0,224 mm up to and
including 2,65 mm
The grade of insulation used for determining the thermal index shall be grade 2 or grade 2B for
self-bonding winding wires.
Wire sizes 0,315 mm and 0,28 mm are permitted for use when the specification size range is
limited to 0,50 mm and finer.
NOTE For round enamelled winding wires, in order to avoid undue fragility of the test specimen, experience has
shown that nominal conductor diameters of 0,800 mm up to and including 2,65 mm are generally found convenient
to handle and test.
60172 Amend. 2 © IEC:2010 – 3 –
Replace the existing Table 1 by the following new Table 1:
Table 1 – Force and number of twists for specimens

Nominal diameter Force Number of twists
mm applied to per 125 mm
wire pairs
N
Over Up to and including
0,224 0,25 0,85 33
0,25 0,35 1,7 23
0,35 0,50 3,4 16
0,50 0,75 7,0 12
0,75 1,05 13,5 8
1,05 1,50 27,0 6
1,50 2,15 54,0 4
2,15 2,65 108,0 3
5.3 Number of test specimens
Replace the text of this subclause by the following new text:
Experience has shown that 20 specimens without impregnation and 10 specimens with
impregnation give results with an acceptable tolerance. A minimum of 10 specimens shall be
used.
5.4 Specimen holder
Replace the last sentence of this subclause by the following new sentence:
The holder shall be designed for at least 10 specimens to decrease handling time.
6 Temperature exposure
Replace the eighth paragraph of this clause by the following new paragraph:
Test specimens should be exposed to a minimum of three and preferably four exposure
temperatures. The lowest temperature, recommended at 20 °C above the desired thermal
class, should be one which results in a time frame to failure of more than 5000 h. The highest
exposure temperature must have a value of at least 100 h to be considered a valid data point.
Exposure temperatures should not be more than 20 °C apart. The accuracy of the temperature
index predicted from the results will increase as the exposure temperature approaches the
temperature to which the insulation is exposed in service.
7 Test voltage and its application
Replace the third paragraph of this clause by the following new paragraph:
The test specimens are removed from the ovens and cooled to room temperature. Each
specimen is subjected to a proof voltage according to the average thickness of the enamel as

– 4 – 60172 Amend. 2 © IEC:2010
specified in Table 3. For self-bonding wires, the self-bonding layer is included in the increase in
diameter due to the insulation.

Annex A
Replace Table A1 by the following new Table A.1:
Table A.1 – Commonly used test temperatures in degrees Celsius and
the corresponding Kelvin’s with its reciprocal and reciprocal squared values
θ T
–1 2 2 –2
X = 1/T (K ) X = 1/T (K )
ºC K
−3 −6
105 378
2,646 × 10 6,999 × 10
−3 −6
120 393
2,545 × 10 6,475 × 10
−3 −6
125 398
2,513 × 10 6,313 × 10
−3 −6
130 403
2,481 × 10 6,157 × 10
−3 −6
140 413
2,421 × 10 5,863 × 10
−3 −6
150 423
2,364 × 10 5,589 × 10
−3 −6
155 428
2,336 × 10 5,459 × 10
−3 −6
165 438
2,283 × 10 5,212 × 10
−3 −6
175 448
2,232 × 10 4,982 × 10
−3 −6
180 453
2,208 × 10 4,873 × 10
−3 −6
185 458
2,183 × 10 4,767 × 10
−3 −6
190 463
2,160 × 10 4,665 × 10
−3 −6
200 473
2,114 × 10 4,470 × 10
−3 −6
210 483
2,070 × 10 4,287 × 10
−3 −6
220 493
2,028 × 10 4,114 × 10
−3 −6
225 498
2,008 × 10 4,032 × 10
−3 −6
230 503
1,988 × 10 3,952 × 10
−3 −6
240 513
1,949 × 10 3,800 × 10
−3 −6
250 523
1,912 × 10 3,656 × 10
−3 −6
260 533
1,876 × 10 3,520 × 10
−3 −6
270 543
1,842 × 10 3,392 × 10
−3 −6
280 5
...