IEC TR 63037:2016
(Main)Electrical interface specifications for self ballasted lamps and controlgear in phase-cut dimmed lighting systems
Electrical interface specifications for self ballasted lamps and controlgear in phase-cut dimmed lighting systems
IEC TR 63037:2016(E) specifies the electrical interface between phase-cut dimming equipment and lighting equipment, such as LED integrated lamps and light sources with external controlgear, with the intention of helping designers of both types of equipment to develop products that will work together properly. This document describes both the dimming phase and the off phase. In addition to the specification of the interface, test procedures are given for testing the proper operation. It may be expected that controlgear fulfilling the requirements of this document are also suited to be used with electronic switches that use a circuitry comparable with that of a phase-cut dimmer, but do not contain means for the adjustability of the phase-cut angle. Safety requirements are not covered by this document, but by respective product standards.
General Information
Relations
Standards Content (Sample)
IEC TR 63037 ®
Edition 1.0 2016-11
TECHNICAL
REPORT
Electrical interface specifications for self ballasted lamps and controlgear in
phase-cut dimmed lighting systems
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form
or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from
either IEC or IEC's member National Committee in the country of the requester. If you have any questions about IEC
copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or
your local IEC member National Committee for further information.
IEC Central Office Tel.: +41 22 919 02 11
3, rue de Varembé Fax: +41 22 919 03 00
CH-1211 Geneva 20 info@iec.ch
Switzerland www.iec.ch
About the IEC
The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes
International Standards for all electrical, electronic and related technologies.
About IEC publications
The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the
latest edition, a corrigenda or an amendment might have been published.
IEC Catalogue - webstore.iec.ch/catalogue Electropedia - www.electropedia.org
The stand-alone application for consulting the entire The world's leading online dictionary of electronic and
bibliographical information on IEC International Standards, electrical terms containing 20 000 terms and definitions in
Technical Specifications, Technical Reports and other English and French, with equivalent terms in 15 additional
documents. Available for PC, Mac OS, Android Tablets and languages. Also known as the International Electrotechnical
iPad. Vocabulary (IEV) online.
IEC publications search - www.iec.ch/searchpub IEC Glossary - std.iec.ch/glossary
The advanced search enables to find IEC publications by a 65 000 electrotechnical terminology entries in English and
variety of criteria (reference number, text, technical French extracted from the Terms and Definitions clause of
committee,…). It also gives information on projects, replaced IEC publications issued since 2002. Some entries have been
and withdrawn publications. collected from earlier publications of IEC TC 37, 77, 86 and
CISPR.
IEC Just Published - webstore.iec.ch/justpublished
Stay up to date on all new IEC publications. Just Published IEC Customer Service Centre - webstore.iec.ch/csc
details all new publications released. Available online and If you wish to give us your feedback on this publication or
also once a month by email. need further assistance, please contact the Customer Service
Centre: csc@iec.ch.
IEC TR 63037 ®
Edition 1.0 2016-11
TECHNICAL
REPORT
Electrical interface specifications for self ballasted lamps and controlgear in
phase-cut dimmed lighting systems
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
ICS 29.140.99 ISBN 978-2-8322-3711-3
– 2 – IEC TR 63037:2016 © IEC 2016
CONTENTS
FOREWORD . 4
INTRODUCTION . 6
1 Scope . 7
2 Normative references . 7
3 Terms, definitions and abbreviated terms . 7
3.1 Terms and definitions . 7
3.2 Abbreviated terms . 9
4 General description . 10
5 General requirements . 10
5.1 Voltage rating . 10
5.2 Frequency rating . 11
5.3 Marking of controlgear . 11
6 Description of the lighting system and its components . 11
6.1 Wiring method . 11
6.2 Wiring diagram . 11
7 Electrical specification . 12
7.1 General . 12
7.2 Electrical characteristics during the on state of a phase-cut dimming system . 12
7.2.1 General . 12
7.2.2 Electrical characteristics for leading edge dimming method . 12
7.2.3 Electrical characteristics for trailing edge dimming method . 17
7.3 Electrical characteristics during the off state of a phase-cut dimming system . 23
8 Test procedures . 24
8.1 General . 24
8.2 Tests for leading edge dimmable devices . 24
8.2.1 General . 24
8.2.2 Test related to the non-conducting phase . 25
8.2.3 Test related to the transition from the non-conducting to the conducting
phase and to the conducting phase. 25
8.3 Tests for trailing edge dimmable devices . 25
8.3.1 General . 25
8.3.2 Test related to the conducting phase . 25
8.3.3 Test related to the transition from the conducting phase to the non-
conducting phase . 26
8.3.4 Test related to the non-conducting phase . 26
8.4 Tests for characteristics during electronic off state . 27
Annex A (informative) Voltage shapes to be used with the tests in IEC TR 63037 . 28
A.1 General . 28
A.2 Waveform description . 28
A.3 Waveform description . 28
Annex B (informative) Equivalent phase-cut dimmer circuit . 29
Bibliography . 30
Figure 1 – Example of wiring diagram . 11
Figure 2 – Timing leading edge dimming method . 13
Figure 3 – Timing trailing edge dimming method . 18
Figure 4 – Test setup for testing the conducting phase . 24
Figure 5 – Test setup for the transition from the conducting to the non-conducting
phase . 26
Figure 6 – Test setup for the non-conducting phase . 27
Figure A.1 – Waveform of AC voltage source . 28
Figure A.2 – Waveform of AC voltage source . 28
Figure B.1 – Scheme of the EC_D . 29
Table 1 – Nominal mains voltage 100 V; frequency 50 Hz or 60 Hz . 14
Table 2 – Nominal mains voltage 120 V; frequency 50 Hz or 60 Hz . 14
Table 3 – Nominal mains voltage 200 V; frequency 50 Hz or 60 Hz . 14
Table 4 – Nominal mains voltage 230 V; frequency 50 Hz or 60 Hz . 15
Table 5 – Nominal mains voltage 277 V; frequency 50 Hz or 60 Hz . 15
Table 6 – Slew rate for voltage decrease across the phase-cut dimmer . 16
Table 7 – Nominal mains voltage 100 V; frequency 50 Hz or 60 Hz . 16
Table 8 – Nominal mains voltage 120 V; frequency 50 Hz or 60 Hz . 16
Table 9 – Nominal mains voltage 200 V; frequency 50 Hz or 60 Hz . 17
Table 10 – Nominal mains voltage 230 V; frequency 50 Hz or 60 Hz . 17
Table 11 – Nominal mains voltage 277 V; frequency 50 Hz or 60 Hz . 17
Table 12 – Nominal mains voltage from 100 V to 277 V; frequency 50 Hz or 60 Hz . 19
Table 13 – Nominal mains voltage 100 V; frequency 50 Hz or 60 Hz . 20
Table 14 – Nominal mains voltage 120 V; frequency 50 Hz or 60 Hz . 21
Table 15 – Nominal mains voltage 200 V; frequency 50 Hz or 60 Hz . 21
Table 16 – Nominal mains voltage 230 V; frequency 50 Hz or 60 Hz . 22
Table 17 – Nominal mains voltage 277 V; frequency 50 Hz or 60 Hz . 22
Table 18 – Currents and voltages for controlgear during the electronic off state . 23
Table 19 – Parameters for testing purposes . 24
– 4 – IEC TR 63037:2016 © IEC 2016
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
ELECTRICAL INTERFACE SPECIFICATIONS
FOR SELF BALLASTED LAMPS AND CONTROLGEAR IN PHASE-CUT
DIMMED LIGHTING SYSTEMS
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.