IEC 62343-1-2:2007

Dynamic modules - Part 1-2: Performance standards - Dynamic chromatic dispersion compensator with pigtails for use in controlled environments (Category C)

This part of IEC 62343 contains the minimum initialisation test and measurement requirements and severities, which an optical dynamic chromatic dispersion compensator (DCDC) shall satisfy in order to be categorised as meeting the requirements of DCDC used in controlled environments. The requirements cover optical dynamic chromatic dispersion compensators for Category C - Controlled environments.

Modules dynamiques - Partie 1-2: Normes de qualité de fonctionnement - Compensateur de dispersion chromatique dynamique avec fibres-amorces, pour usage en environnements contrôlés (Catégorie C)

La présente partie de la CEI 62343 contient les sévérités et les exigences minimales d'essai et de mesure initiales, qu'un compensateur de dispersion chromatique dynamique optique (CDCD) doit satisfaire afin d'être classé comme conforme aux exigences d'un CDCD utilisé dans des environnements contrôlés. Les exigences couvrent les compensateurs de dispersion chromatique dynamiques optiques pour la catégorie C - Environnements contrôlés.

General Information

• Status: Published
• Publication Date: 10-Jul-2007
• ICS: 33.180.30 - Optic amplifiers
• Technical Committee: SC 86C - Fibre optic systems and active devices
• Drafting Committee: WG 5 - TC 86/SC 86C/WG 5
• Current Stage: DELPUB - Deleted Publication
• Completion Date: 25-Jun-2015

Relations

• Revised: IEC 62343-1-2:2015 - Dynamic modules - Part 1-2: Performance standards - Tuneable chromatic dispersion compensator (non-connectorized)
• Effective Date: 05-Sep-2023

Standards Content (Sample)

INTERNATIONAL IEC
STANDARD
CEI
62343-1-2
NORME
First edition
INTERNATIONALE
Première édition
2007-07
Dynamic modules –
Part 1-2:
Performance standards –
Dynamic chromatic dispersion
compensator with pigtails for use
in controlled environments (Category C)

Modules dynamiques –
Partie 1-2:
Normes de qualité de fonctionnement –
Compensateur de dispersion chromatique
dynamique avec fibres-amorces, pour usage
en environnements contrôlés (Catégorie C)
Reference number
Numéro de référence
IEC/CEI 62343-1-2:2007
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form
or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from
either IEC or IEC's member National Committee in the country of the requester.
If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publication,
please contact the address below or your local IEC member National Committee for further information.

Droits de reproduction réservés. Sauf indication contraire, aucune partie de cette publication ne peut être reproduite
ni utilisée sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie
et les microfilms, sans l'accord écrit de la CEI ou du Comité national de la CEI du pays du demandeur.
Si vous avez des questions sur le copyright de la CEI ou si vous désirez obtenir des droits supplémentaires sur cette
publication, utilisez les coordonnées ci-après ou contactez le Comité national de la CEI de votre pays de résidence.

IEC Central Office
3, rue de Varembé
CH-1211 Geneva 20
Switzerland
Email: [e-mail]
Web: www.iec.ch
About the IEC
The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes
International Standards for all electrical, electronic and related technologies.

About IEC publications
The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the
latest edition, a corrigenda or an amendment might have been published.
ƒ Catalogue of IEC publications: www.iec.ch/searchpub
The IEC on-line Catalogue enables you to search by a variety of criteria (reference number, text, technical committee,…).
It also gives information on projects, withdrawn and replaced publications.
ƒ IEC Just Published: www.iec.ch/online_news/justpub
Stay up to date on all new IEC publications. Just Published details twice a month all new publications released. Available
on-line and also by email.
ƒ Customer Service Centre: www.iec.ch/webstore/custserv
If you wish to give us your feedback on this publication or need further assistance, please visit the Customer Service
Centre FAQ or contact us:
Email: [e-mail]
Tel.: [phone]
Fax: [phone]
A propos de la CEI
La Commission Electrotechnique Internationale (CEI) est la première organisation mondiale qui élabore et publie des
normes internationales pour tout ce qui a trait à l'électricité, à l'électronique et aux technologies apparentées.

A propos des publications CEI
Le contenu technique des publications de la CEI est constamment revu. Veuillez vous assurer que vous possédez
l’édition la plus récente, un corrigendum ou amendement peut avoir été publié.
ƒ Catalogue des publications de la CEI: www.iec.ch/searchpub/cur_fut-f.htm
Le Catalogue en-ligne de la CEI vous permet d’effectuer des recherches en utilisant différents critères (numéro de
référence, texte, comité d’études,…). Il donne aussi des informations sur les projets et les publications retirées ou
remplacées.
ƒ Just Published CEI: www.iec.ch/online_news/justpub
Restez informé sur les nouvelles publications de la CEI. Just Published détaille deux fois par mois les nouvelles
publications parues. Disponible en-ligne et aussi par email.
ƒ Service Clients: www.iec.ch/webstore/custserv/custserv_entry-f.htm
Si vous désirez nous donner des commentaires sur cette publication ou si vous avez des questions, visitez le FAQ du
Service clients ou contactez-nous:
Email: [e-mail]
Tél.: [phone]
Fax: [phone]
INTERNATIONAL IEC
STANDARD
CEI
62343-1-2
NORME
First edition
INTERNATIONALE
Première édition
2007-07
Dynamic modules –
Part 1-2:
Performance standards –
Dynamic chromatic dispersion
compensator with pigtails for use
in controlled environments (Category C)

Modules dynamiques –
Partie 1-2:
Normes de qualité de fonctionnement –
Compensateur de dispersion chromatique
dynamique avec fibres-amorces, pour usage
en environnements contrôlés (Catégorie C)
PRICE CODE
L
CODE PRIX
Commission Electrotechnique Internationale
International Electrotechnical Commission
МеждународнаяЭлектротехническаяКомиссия
For price, see current catalogue
Pour prix, voir catalogue en vigueur

– 2 – 62343-1-2 © IEC:2007
CONTENTS
FOREWORD.3

1 Scope.5
2 Normative references .5
3 Terms and definitions .6
4 Test.6
4.1 General .6
4.2 Module .6
4.3 Spectral bands .7
5 Test report.7
6 Reference modules .7
7 Performance requirements .7
7.1 Dimensions .7
7.2 Sample size .7
7.3 Test details and requirements .8

Bibliography.10

Table 1 – Spectral bands for single-mode systems (ITU-T G. Sup39).7
Table 2 – Test and requirements for type A (Multi/single channel type DCDC with
large dispersion variable range).8
Table 3 – Test and requirements for type B (Multi/single channel type DCDC with
standard dispersion variable range) .9

62343-1-2 © IEC:2007 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
DYNAMIC MODULES –
Part 1-2: Performance standards –
Dynamic chromatic dispersion compensator
with pigtails for use in controlled environments
(Category C)
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any
equipment declared to be in conformity with an IEC Publication.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 62343-1-2 has been prepared by subcommittee 86C: Fibre optic
systems and active devices, of IEC technical committee 86: Fibre optics.
The text of this standard is based on the following documents:
CDV Result of voting
86C/698/CDV 86C/755/RVC
Full information on the voting for the approval of this standard can be found in the report on
voting indicated in the above table.
This publication has been drafted in accordance with the ISO/IEC Directives, Part 2.

– 4 – 62343-1-2 © IEC:2007
A list of all parts of IEC 62343 series, under the general title Dynamic modules, can be found
on the IEC website.
The committee has decided that the contents of this publication will remain unchanged until
the maintenance result date indicated on the IEC web site under "http://webstore.iec.ch" in
the data related to the specific publication. At this date, the publication will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.
62343-1-2 © IEC:2007 – 5 –
DYNAMIC MODULES –
Part 1-2: Performance standards –
Dynamic chromatic dispersion compensator
with pigtails for use in controlled environments
(Category C)
1 Scope
This part of IEC 62343 contains the minimum initialisation test and measurement
requirements and severities, which an optical dynamic chromatic dispersion compensator
(DCDC) shall satisfy in order to be categorised as meeting the requirements of DCDC used in
controlled environments. The requirements cover optical dynamic chromatic dispersion
compensators for Category C – Controlled environments.
2 Normative references
The following referenced documents are indispensable for the application of this document.
For dated references, only the edition cited applies. For undated references, the latest edition
of the referenced document (including any amendments) applies.
IEC 61300 (all parts), Fibre optic interconnecting devices and passive components – Basic
test and measurement procedures
IEC 61300-1, Fibre optic interconnecting devices and passive components – Basic test and
measurement procedures – Part 1: General and guidance
IEC 61300-3-2, Fibre optic interconnecting devices and passive components – Basic test and
measurement procedures – Part 3-2: Examinations and measurements – Polarization
dependence of attenuation in a single-mode fibre optic device
IEC 61300-3-29, Fibre optic interconnecting devices and passive components – Basic test
and measurement procedures – Part 3-29: Examinations and measurements – Measurement
techniques for characterizing the amplitude of the spectral transfer function of DWDM
components
IEC 61300-3-32, Fibre optic interconnecting devices and passive components – Basic test
and measurement procedures – Part 3-32: Examinations and measurements – Polarization
mode dispersion measurement for passive optical components
IEC 61753-021-2: Fibre optic interconnecting devices and passive components performance
standard – Part 021-2: Fibre optic connectors terminated on single-mode fibre for category C
– Controlled environment
ITU-T Recommendation G.671: Transmission characteristics of optical components and sub-
systems
ITU-T Recommendation G.692: Optical interfaces for multichannel systems with optical
amplifiers
ITU-T G. Sup39: Optical system design and engineering considerations

– 6 – 62343-1-2 © IEC:2007
3 Terms and definitions
For the purposes of this document, the following definitions apply.
3.1
dynamic chromatic dispersion compensator
two-port in-line device that is capable of transforming, by internal or external automatic
control, an i
...