iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
IEC

IEC 60404-1:2000

(Main)

Magnetic materials - Part 1: Classification

Magnetic materials - Part 1: Classification

Intended to classify commercially available magnetic materials. The term "magnetic materials" denotes substances where the application requires the existence of ferromagnetic or ferrimagnetic properties. The classification of magnetic materials is based upon the generally recognized existence of two main groups of products. - soft magnetic materials (coercivity less than or equal to 1000 A/m) - hard magnetic materials (coercivity greater than 1000 A/m) Within these main groups, the classification when appropriate recognizes the following characteristics: - the main allowing element and the metallurgical state and physical properties of the material; - when possible and convenient, the relationship between these characteristics is identified. A classification by specific areas of application cannot be applied to all materials because different materials can very often be used for the same application depending on the characteristics required.

Matériaux magnétiques - Partie 1: Classification

Pour objet la classification des matériaux magnétiques disponibles commercialement. Le terme "matériaux magnétiques" décrit les substances dont l'application exige l'existence de caractéristiques ferromagnétiques ou ferrimagnétiques. La classification des matériaux magnétiques est basée sur l'existence généralement reconnue de deux groupes principaux de produits: - les matériaux magnétiques doux (coercivité inférieure ou égale à 1000 A/m) - les matériaux magnétiques durs (coercivité plus grande que 1000 A/m). A l'intérieur de ces groupes principaux, la classification reconnaît lorsque cela est approprié les caractéristiques suivantes: - l'élément principal d'alliage et l'état métallurgique et les caractéristiques physiques du matériau; - lorsque cela est possible et réalisable pratiquement, la relation entre ces caractéristiques est identifiée. Une classification selon les domaines spécifiques d'application ne peut être appliquée à tous les matériaux, car différents matériaux peuvent bien souvent être utilisés pour la même application en fonction des caractéristiques requises.

General Information

Status
Published
Publication Date
29-Aug-2000
ICS
29.030 - Magnetic materials
Technical Committee
TC 68 - Magnetic alloys and steels
Drafting Committee
WG 1 - TC 68/WG 1
Current Stage
DELPUB - Deleted Publication
Completion Date
24-Oct-2016
Ref Project

Relations

Revised
IEC 60404-1:2016 - Magnetic materials - Part 1: Classification
Effective Date
05-Sep-2023

Buy Standard

IEC 60404-1:2000 - Magnetic materials - Part 1: Classification Released:8/30/2000 Isbn:2831853346IEC 60404-1:2000 - Magnetic materials - Part 1: Classification Released:8/30/2000 Isbn:2831853346
PreviousNext
Standard
IEC 60404-1:2000 - Magnetic materials - Part 1: Classification Released:8/30/2000 Isbn:2831853346
English and French language
115 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)


1250( &(,
,17(51$7,21$/( ,(&

,17(51$7,21$/
'HX[LqPHpGLWLRQ
67$1'$5'
6HFRQGHGLWLRQ

0DWpULDX[PDJQpWLTXHV±
3DUWLH
&ODVVLILFDWLRQ
0DJQHWLFPDWHULDOV±
3DUW
&ODVVLILFDWLRQ
1XPpURGHUpIpUHQFH
5HIHUHQFHQXPEHU
&(,,(&
1XPpURVGHVSXEOLFDWLRQV 1XPEHULQJ
'HSXLVOHHUMDQYLHUOHVSXEOLFDWLRQVGHOD&(, $V IURP  -DQXDU\  DOO ,(& SXEOLFDWLRQV DUH
VRQWQXPpURWpHVjSDUWLUGH LVVXHGZLWKDGHVLJQDWLRQLQWKHVHULHV
3XEOLFDWLRQVFRQVROLGpHV &RQVROLGDWHGSXEOLFDWLRQV
/HVYHUVLRQVFRQVROLGpHVGHFHUWDLQHVSXEOLFDWLRQVGH &RQVROLGDWHG YHUVLRQV RI VRPH ,(& SXEOLFDWLRQV
OD&(,LQFRUSRUDQWOHVDPHQGHPHQWVVRQWGLVSRQLEOHV LQFOXGLQJ DPHQGPHQWV DUH DYDLODEOH )RU H[DPSOH
3DU H[HPSOH OHV QXPpURV G¶pGLWLRQ   HW  HGLWLRQQXPEHUVDQGUHIHUUHVSHFWLYHO\WR
LQGLTXHQW UHVSHFWLYHPHQW OD SXEOLFDWLRQ GH EDVH OD WKH EDVH SXEOLFDWLRQ WKH EDVH SXEOLFDWLRQ LQFRU
SXEOLFDWLRQGHEDVHLQFRUSRUDQWO¶DPHQGHPHQWHWOD SRUDWLQJ DPHQGPHQW  DQG WKH EDVH SXEOLFDWLRQ
SXEOLFDWLRQ GH EDVH LQFRUSRUDQW OHV DPHQGHPHQWV  LQFRUSRUDWLQJDPHQGPHQWVDQG
HW
9DOLGLWpGHODSUpVHQWHSXEOLFDWLRQ 9DOLGLW\RIWKLVSXEOLFDWLRQ
/HFRQWHQXWHFKQLTXHGHVSXEOLFDWLRQVGHOD&(,HVW 7KH WHFKQLFDO FRQWHQW RI ,(& SXEOLFDWLRQV LV NHSW
FRQVWDPPHQWUHYXSDUOD &(, DILQ TX
LO UHIOqWH O
pWDW XQGHUFRQVWDQWUHYLHZE\WKH,(&WKXVHQVXULQJWKDW
DFWXHOGHODWHFKQLTXH WKHFRQWHQWUHIOHFWVFXUUHQWWHFKQRORJ\
'HV UHQVHLJQHPHQWV UHODWLIV j OD GDWH GH UHFRQILU ,QIRUPDWLRQUHODWLQJWRWKHGDWHRIWKHUHFRQILUPDWLRQ
PDWLRQ GH OD SXEOLFDWLRQ VRQW GLVSRQLEOHV GDQV OH RIWKHSXEOLFDWLRQLVDYDLODEOHLQWKH,(&FDWDORJXH
&DWDORJXHGHOD&(,
/HVUHQVHLJQHPHQWVUHODWLIVjGHVTXHVWLRQVjO¶pWXGHHW ,QIRUPDWLRQRQWKHVXEMHFWVXQGHUFRQVLGHUDWLRQDQG
GHVWUDYDX[HQFRXUVHQWUHSULVSDUOHFRPLWpWHFKQLTXH ZRUN LQ SURJUHVV XQGHUWDNHQ E\ WKH WHFKQLFDO
TXL D pWDEOL FHWWH SXEOLFDWLRQ DLQVL TXH OD OLVWH GHV FRPPLWWHHZKLFKKDVSUHSDUHGWKLVSXEOLFDWLRQDVZHOO
SXEOLFDWLRQVpWDEOLHVVHWURXYHQWGDQVOHVGRFXPHQWVFL DVWKHOLVWRISXEOLFDWLRQVLVVXHGLVWREHIRXQGDWWKH
GHVVRXV IROORZLQJ,(&VRXUFHV
• ©6LWHZHEªGHOD&(,
• ,(&ZHEVLWH
• &DWDORJXHGHVSXEOLFDWLRQVGHOD&(, • &DWDORJXHRI,(&SXEOLFDWLRQV
3XEOLpDQQXHOOHPHQWHWPLVjMRXU 3XEOLVKHG\HDUO\ZLWKUHJXODUXSGDWHV
UpJXOLqUHPHQW 2QOLQHFDWDORJXH
&DWDORJXHHQOLJQH
• ,(&%XOOHWLQ
• %XOOHWLQGHOD&(, $YDLODEOHERWKDWWKH,(&ZHEVLWH
DQG
'LVSRQLEOHjODIRLVDX©VLWHZHEªGHOD&(,
DVDSULQWHGSHULRGLFDO
HWFRPPHSpULRGLTXHLPSULPp
7HUPLQRORJ\JUDSKLFDODQGOHWWHU
7HUPLQRORJLHV\PEROHVJUDSKLTXHV
V\PEROV
HWOLWWpUDX[
)RU JHQHUDO WHUPLQRORJ\ UHDGHUV DUH UHIHUUHG WR
(QFHTXLFRQFHUQHODWHUPLQRORJLHJpQpUDOHOHOHFWHXU ,(&,QWHUQDWLRQDO(OHFWURWHFKQLFDO9RFDEXODU\
VH UHSRUWHUD j OD &(, 9RFDEXODLUH(OHFWUR ,(9 
WHFKQLTXH,QWHUQDWLRQDO 9(, 
)RUJUDSKLFDOV\PEROVDQGOHWWHUV\PEROVDQGVLJQV
3RXUOHVV\PEROHVJUDSKLTXHVOHVV\PEROHVOLWWpUDX[ DSSURYHG E\ WKH ,(& IRU JHQHUDO XVH UHDGHUV DUH
HWOHVVLJQHVG
XVDJHJpQpUDODSSURXYpVSDUOD&(,OH UHIHUUHGWRSXEOLFDWLRQV,(&/HWWHUV\PEROVWR
OHFWHXUFRQVXOWHUDOD&(,6\PEROHVOLWWpUDX[j EHXVHGLQHOHFWULFDOWHFKQRORJ\,(&*UDSKLFDO
XWLOLVHUHQpOHFWURWHFKQLTXHOD&(,6\PEROHV V\PEROV IRU XVH RQ HTXLSPHQW ,QGH[ VXUYH\ DQG
JUDSKLTXHVXWLOLVDEOHVVXUOHPDWpULHO,QGH[UHOHYpHW FRPSLODWLRQ RI WKH VLQJOH VKHHWV DQG ,(& 
FRPSLODWLRQGHVIHXLOOHVLQGLYLGXHOOHVHWOD&(, *UDSKLFDOV\PEROVIRUGLDJUDPV
6\PEROHVJUDSKLTXHVSRXUVFKpPDV

 6HHZHEVLWHDGGUHVVRQWLWOHSDJH

 9RLUDGUHVVH©VLWHZHEªVXUODSDJHGHWLWUH

1250( &(,
,17(51$7,21$/( ,(&

,17(51$7,21$/
'HX[LqPHpGLWLRQ
67$1'$5'
6HFRQGHGLWLRQ

0DWpULDX[PDJQpWLTXHV±
3DUWLH
&ODVVLILFDWLRQ
0DJQHWLFPDWHULDOV±
3DUW
&ODVVLILFDWLRQ
©,(&'URLWVGHUHSURGXFWLRQUpVHUYpV⎯&RS\ULJKWDOOULJKWVUHVHUYHG
$XFXQHSDUWLHGHFHWWHSXEOLFDWLRQQHSHXWrWUHUHSURGXLWHQL 1RSDUWRIWKLVSXEOLFDWLRQPD\EHUHSURGXFHGRUXWLOL]HGLQ
XWLOLVpHVRXVTXHOTXHIRUPHTXHFHVRLWHWSDUDXFXQSURFpGp DQ\ IRUP RU E\ DQ\ PHDQV HOHFWURQLF RU PHFKDQLFDO
pOHFWURQLTXHRXPpFDQLTXH\FRPSULVODSKRWRFRSLHHWOHV LQFOXGLQJSKRWRFRS\LQJDQGPLFURILOPZLWKRXWSHUPLVVLRQLQ
PLFURILOPVVDQVO
DFFRUGpFULWGHO
pGLWHXU ZULWLQJIURPWKHSXEOLVKHU
,QWHUQDWLRQDO(OHFWURWHFKQLFDO&RPPLVVLRQ UXHGH9DUHPEp*HQHYD6ZLW]HUODQG
7HOHID[ HPDLOLQPDLO#LHFFK ,(&ZHEVLWHKWWSZZZLHFFK
&2'(35,;
&RPPLVVLRQ (OHFWURWHFKQLTXH ,QWHUQDWLRQDOH
;$
35,&(&2'(
,QWHUQDWLRQDO (OHFWURWHFKQLFDO &RPPLVVLRQ
3RXUSUL[YRLUFDWDORJXHHQYLJXHXU
)RUSULFHVHHFXUUHQWFDWDORJXH

±± ©&(,
6200$,5(
3DJHV
$9$17352326
$UWLFOHV
 *pQpUDOLWpV
 'RPDLQHG¶DSSOLFDWLRQHWREMHW 
 5pIpUHQFHVQRUPDWLYHV
 'pILQLWLRQV 
 0DWpULDX[PDJQpWLTXHVGRX[ FRHUFLWLYLWp≤N$P 
 &ODVVH$±)HUV
 *pQpUDOLWpV
 &DUDFWpULVWLTXHVSK\VLTXHV
 $SSOLFDWLRQVSULQFLSDOHV
 &ODVVH%±$FLHUVGRX[jIDLEOHWHQHXUHQFDUERQH
 &ODVVH%±3URGXLWVPDVVLIV
 &ODVVH%±3URGXLWVSODWV 
 &ODVVH&±$FLHUVDXVLOLFLXP
 &ODVVH&±3URGXLWVPDVVLIV
 &ODVVH&±3URGXLWVSODWV
 &ODVVH'±$XWUHVW\SHVG
DFLHUV
 &ODVVH'±3URGXLWVPDVVLIV
 &ODVVH'±3URGXLWVSODWV
 &ODVVH'±$FLHUVLQR[\GDEOHV
 &ODVVH(±$OOLDJHVIHUQLFNHO
 &ODVVH(±7HQHXUHQQLFNHOFRPSULVHHQWUHHW
 &ODVVH(±7HQHXUHQQLFNHOFRPSULVHHQWUHHW
 &ODVVH(±7HQHXUHQQLFNHOFRPSULVHHQWUHHW
 &ODVVH(±7HQHXUHQQLFNHOFRPSULVHHQWUHHW
 &ODVVH(±7HQHXUHQQLFNHOFRPSULVHHQWUHHW
 &ODVVH)±$OOLDJHVIHUFREDOW
 &ODVVH)±7HQHXUHQFREDOWFRPSULVHHQWUHHW
 &ODVVH)±7HQHXUHQFREDOWGH
 &ODVVH)±7HQHXUHQFREDOWHQWUHHW
 &ODVVH*±$XWUHVDOOLDJHV
 &ODVVH*±$OOLDJHVIHUDOXPLQLXP
 &ODVVH*±$OOLDJHVIHUDOXPLQLXPVLOLFLXP 
 &ODVVH+±0DWpULDX[PDJQpWLTXHVGRX[REWHQXVSDUOHVWHFKQLTXHVGH
ODPpWDOOXUJLHGHVSRXGUHV
 &ODVVH+±)HUULWHVGRX[
 &ODVVH+±0DWpULDX[PDJQpWLTXHVGRX[IULWWpV
 &ODVVH+±3RXGUHVFRPSRVLWHV
 &ODVVH,±0DWpULDX[PDJQpWLTXHVGRX[DPRUSKHV
 &ODVVH,±$OOLDJHVjEDVHIHU
 &ODVVH,±$OOLDJHVjEDVHFREDOW
 &ODVVH,±$OOLDJHVjEDVHQLFNHO

©,(& ±±
&217(176
3DJH
)25(:25' 
&ODXVH
 *HQHUDO
 6FRSHDQGREMHFW
 1RUPDWLYHUHIHUHQFHV
 'HILQLWLRQV 
 0DJQHWLFDOO\VRIWPDWHULDOV FRHUFLYLW\≤N$P 
 &ODVV$±,URQV
 *HQHUDO
 3K\VLFDOFKDUDFWHULVWLFV
 0DLQDSSOLFDWLRQV
 &ODVV%±/RZFDUERQPLOGVWHHOV
 &ODVV%±%XONPDWHULDO
 &ODVV%±)ODWPDWHULDO
 &ODVV&±6LOLFRQVWHHOV
 &ODVV&±%XONPDWHULDO
 &ODVV&±)ODWPDWHULDO
 &ODVV'±2WKHUVWHHOV
 &ODVV'±%XONPDWHULDO
 &ODVV'±)ODWPDWHULDO
 &ODVV'±6WDLQOHVVVWHHOV
 &ODVV(±1LFNHOLURQDOOR\V
 &ODVV(±1LFNHOFRQWHQWWR
 &ODVV(±1LFNHOFRQWHQWWR
 &ODVV(±1LFNHOFRQWHQWWR
 &ODVV(±1LFNHOFRQWHQWWR
 &ODVV(±1LFNHOFRQWHQWWR
 &ODVV)±,URQFREDOWDOOR\V
 &ODVV)±&REDOWFRQWHQWWR
 &ODVV)±&REDOWFRQWHQW
 &ODVV)±&REDOWFRQWHQWWR
 &ODVV*±2WKHUDOOR\V
 &ODVV*±$OXPLQLXPLURQDOOR\V
 &ODVV*±$OXPLQLXPVLOLFRQLURQDOOR\V
 &ODVV+±0DJQHWLFDOO\VRIWPDWHULDOVPDGHE\SRZGHUPHWDOOXUJLFDOWHFKQLTXHV
 &ODVV+±6RIWIHUULWHV
 &ODVV+±0DJQHWLFDOO\VRIWVLQWHUHGPDWHULDOV
 &ODVV+±3RZGHUFRPSRVLWHV
 &ODVV,±$PRUSKRXVVRIWPDJQHWLFPDWHULDOV
 &ODVV,±,URQEDVHGDOOR\V
 &ODVV,±&REDOWEDVHGDOOR\V 
 &ODVV,±1LFNHOEDVHGDOOR\V

±± ©&(,
$UWLFOHV 3DJHV
 0DWpULDX[PDJQpWLTXHVGXUV FRHUFLWLYLWp!N$P 
 &ODVVH4±$OOLDJHVPDJQpWRVWULFWLIV±$OOLDJHVIHUWHUUHVUDUHV FODVVH4 
 *pQpUDOLWpV
 &DUDFWpULVWLTXHVSK\VLTXHV
 $SSOLFDWLRQVSULQFLSDOHV
 &ODVVH5±$OOLDJHVPDJQpWLTXHVGXUV
 &ODVVH5±$
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

IEC
IEC 60404-1-1:2004(Main)
Magnetic materials - Part 1-1: Classification - Surface insulations of electrical steel sheet, strip and laminations

Establishes a classification of surface insulations for electrical steel sheet, strip and laminations according to their general composition, relative insulating ability and function. These surface insulations are either oxide layers or applied coatings. The purpose of this classification is to create a nomenclature for the various types of surface insulations and to assist users of surface insulations by providing general information about the chemical nature and use of the surface insulations. It is not the intent of this classification to specify insulation requirements in terms of specific values of surface insulation resistance. Such requirements are agreed between the purchaser and the steel producer, where applicable. The classification is used in conjunction with the various specifications for cold rolled electrical steels (see the standards in the IEC 60404-8 series in Clause 2).

  • Standard
    16 pages
    English language
    sale 15% off
  • Standard
    13 pages
    English and French language
    sale 15% off
IEC
IEC 60404-1-1:2004/AMD1:2024(Amendment)
Amendment 1 - Magnetic materials - Part 1-1: Classification - Surface insulations of electrical steel strip, sheet and laminations
  • Standard
    4 pages
    English language
    sale 15% off
IEC
IEC 60404-8-3:2023(Main)
Magnetic materials - Part 8-3: Specifications for individual materials - Cold-rolled non-oriented electrical steel strip and sheet delivered in the semi-processed state

IEC 60404-8-3:2023 defines the grades of cold-rolled non-oriented electrical steel strip and sheet delivered in the semi-processed state in nominal thicknesses of 0,47 mm, 0,50 mm, 0,64 mm, 0,65 mm and 0,79 mm. It gives general requirements, magnetic properties, geometric characteristics, tolerances and technical characteristics as well as inspection procedures. The nominal thicknesses of 0,47 mm, 0,64 mm and 0,79 mm apply to the grades for use at 60 Hz only.
This document applies to cold-rolled non-oriented electrical steel strip and sheet delivered in the semi-processed state, i.e. without final heat treatment, in coils or sheets, and intended for the construction of magnetic circuits. This document does not apply to materials supplied in the fully-processed state.
These materials correspond respectively to classes B2 and C21 of IEC 60404-1.
This edition includes the following significant technical changes with respect to the previous edition:
a) Modification of terms and technical requirements concerning geometrical characteristics to be consistent with IEC 60404-9:2018;
b) Insertion of Table 3 – Tolerances on nominal thickness;
c) Change of the length of the test specimen for determination of geometrical characteristics from 2 m to 1 m;
d) Deletion of Annex A with the European numerical system of designation of steels.

  • Standard
    45 pages
    English and French language
    sale 15% off
IEC
IEC 60404-8-1:2023(Main)
Magnetic materials - Part 8-1: Specifications for individual materials - Permanent magnet (magnetically hard) materials

IEC 60404-8-1:2023 specifies minimum values for the principal magnetic properties of, and dimensional tolerances for, technically important permanent magnet (magnetically hard) materials.
For information purposes only, this document provides values for the densities of the materials and the ranges of their chemical compositions.
This fourth edition includes the following significant technical changes with respect to the previous edition:
a) recently developed anisotropic REFeB hot deformed magnets and anisotropic HDDR REFeB bonded magnets are included;
b) high energy Ca-La-Co ferrites stabilized by La and Co substitution are included;
c) new and high-performance grades of REFeB and RE2Co17 sintered magnets and isotropic REFeN bonded magnets are added.

  • Standard
    95 pages
    English and French language
    sale 15% off
IEC
IEC 60404-12:2023(Main)
Magnetic materials - Part 12: Methods of test for the assessment of the thermal endurance of surface insulation coatings on electrical steel strip and sheet

IEC 60404-12:2023 is applicable to surface insulation coatings on electrical steel strip and sheet classified in IEC 60404-1-1.
This document defines the general principles and technical details of the tests for the assessment of the thermal endurance of surface insulation coatings on electrical steel strip and sheet.
The assessment is made by evaluating the change of a specified property of the surface insulation coating due to a heat treatment at a specified temperature up to 850 °C for a specified duration time up to 2 500 h. The specified property is measured at an ambient temperature of (23 ± 5) °C both without heat treatment and after heat treatment.
This edition includes the following significant technical changes with respect to the previous edition:  
the method of test for adhesion has been modified to match to the method of bend test specified in ISO 1519 using a cylindrical mandrel of 32 mm in diameter instead of the 30 mm diameter mandrel specified in the first edition;
the method of test for interlaminar insulation resistance has been modified to match to the method specified in IEC 60404-11 and the modified Franklin test has been removed;
the method of test for compressibility has been modified to match to the method of test for stacking factor specified in IEC 60404-13;
the concept of "resistance grades" has been removed;
the clamping pressure to be used at temperature ratings above 500 °C has been reduced to (0,01 ± 0,001) N/mm2;
the testing for continuous exposure has been made a subject to an agreement between the manufacturer and the purchaser and the procedure has been moved to an informative Annex A.

  • Standard
    27 pages
    English and French language
    sale 15% off
IEC
IEC 60404-3:2022(Main)
Magnetic materials - Part 3: Methods of measurement of the magnetic properties of electrical steel strip and sheet by means of a single sheet tester

IEC 60404-3:2022 is applicable to grain-oriented and non-oriented electrical steel strip and sheet for measurement of AC magnetic properties at power frequencies. The object of this document is to define the general principles and the technical details of the measurement of the magnetic properties of electrical steel strip and sheet by means of a single sheet tester (SST). This edition includes the following significant technical changes with respect to the previous edition:
- Annex A was revised. The method of determining the yokes’ lamination resistance was added to Annex A;
- Annex B of the consolidated version of 2010 referred to calibration of the SST using the Epstein method. It was cancelled;
- Annex B (new), Annex C and Annex D were revised, they are for information only;
- Annex C was modified taking account of the new situation regarding P and R grades;
- Annex D was amended by addition of Clause D.4 on the numerical air flux compensation.

  • Standard
    100 pages
    English language
    sale 15% off
  • Standard
    64 pages
    English and French language
    sale 15% off
IEC
IEC 60404-8-4:2022(Main)
Magnetic materials - Part 8-4: Specifications for individual materials - Cold-rolled non-oriented electrical steel strip and sheet delivered in the fully-processed state

IEC 60404-8-4:2022 defines the grades of cold-rolled non-oriented electrical steel strip and sheet in nominal thicknesses of 0,35 mm, 0,47 mm, 0,50 mm, 0,65 mm and 1,00 mm. In particular, it gives general requirements, magnetic properties, geometric characteristics, tolerances and technological characteristics, as well as inspection procedure. The nominal thickness 0,47 mm applies to the grades for use at 60 Hz only. This document applies to cold-rolled non-oriented electrical steel strip and sheet supplied in the fully-processed state, i.e. the final annealed condition, in coils or sheets, and intended for the construction of magnetic circuits. This document does not apply to materials supplied in the semi-processed state. This edition includes the following significant technical changes with respect to the previous edition:
- modification of terms and technical requirements concerning geometrical characteristics to be consistent with IEC 60404-9:2018;
- insertion of Table 3 - Tolerances on nominal thickness;
- change of the length of test specimen for determination of geometrical characteristics from 2 m to 1 m.

  • Standard
    80 pages
    English language
    sale 15% off
  • Standard
    52 pages
    English and French language
    sale 15% off
IEC
IEC 60404-17:2021(Main)
Magnetic materials - Part 17: Methods of measurement of the magnetostriction characteristics of grain-oriented electrical steel strip and sheet by means of a single sheet tester and an optical sensor

IEC 60404-17:2021 is applicable to grain-oriented electrical steel strip and sheet specified in IEC 60404-8-7 for the measurement of magnetostriction characteristics under an applied AC magnetic field at 50 Hz or 60 Hz.
This document defines the general principles and technical details of the measurement of magnetostriction characteristics of grain-oriented electrical steel strip and sheet by means of a single sheet tester and an optical sensor.
This document is applicable to the measurement of:
the butterfly loop;
the peak-to-peak value λp-p;
the zero-to-peak value λ0-p.  The magnetostriction characteristics are determined for a sinusoidal induced secondary voltage, for a specified peak value of the magnetic polarization and at a specified magnetizing frequency.

  • Standard
    93 pages
    English and French language
    sale 15% off
IEC
IEC 60404-11:2021(Main)
Magnetic materials - Part 11: Methods of measurement of the surface insulation resistance of electrical steel strip and sheet

IEC 60404-11:2021 is applicable to electrical steel strip and sheet insulated by coating on one or both sides.
The object of this document is to define the general principles and technical details of the measurement of the surface insulation resistance of electrical steel strip and sheet.
NOTE This test is suitable for manufacturing and quality control in the application of insulation coatings.
This edition includes the following significant technical changes with respect to the previous edition:  
Method B has been deleted and the measurement of individual currents through each contact button is enabled by Method A;
an improved arrangement of the test apparatus and the voltage stabilizing circuit for Method A, “Arrangement B”, is introduced.
an alternative layout using two pairs of contact assemblies in opposing position of the test specimen is introduced;
the restriction: “The same area of the test specimen shall not be used to test both sides.” has been deleted.

  • Standard
    24 pages
    English and French language
    sale 15% off
IEC
IEC 60404-6:2018(Main)
Magnetic materials - Part 6: Methods of measurement of the magnetic properties of magnetically soft metallic and powder materials at frequencies in the range 20 Hz to 100 kHz by the use of ring specimens

IEC 60404-6:2018 specifies methods for the measurement of AC magnetic properties of soft magnetic materials, other than electrical steels and soft ferrites, in the frequency range 20 Hz to 100 kHz. The materials covered by this part of IEC 60404 include those speciality alloys listed in IEC 60404-8-6, amorphous and nano-crystalline soft magnetic materials, pressed and sintered and metal injection moulded parts such as are listed in IEC 60404-8-9, cast parts and magnetically soft composite materials. The object of this part is to define the general principles and the technical details of the measurement of the magnetic properties of magnetically soft materials by means of ring methods. For materials supplied in powder form, a ring test specimen is formed by the appropriate pressing method for that material. The measurement of the DC magnetic properties of soft magnetic materials is made in accordance with the ring method of IEC 60404-4. The determinations of the magnetic characteristics of magnetically soft components are made in accordance with IEC 62044-3. This edition includes the following significant technical changes with respect to the previous edition:
a) adaption to modern measurement and evaluation methods, in particular the introduction of the widely spread digital sampling method for the acquisition and evaluation of the measured data;
b) limitation of the frequency range up to 100 kHz;
c) deletion of Clause 7 of the second edition that specified the measurement of magnetic properties using a digital impedance bridge;
d) addition of a new Clause 7 on the measurement of the specific total loss by the wattmeter method, including an example of the application of the digital sampling method;
e) addition of an informative annex on the technical details of the digital sampling technique for the determination of magnetic properties.
The contents of the corrigendum of November 2018 have been included in this copy.

  • Standard
    81 pages
    English language
    sale 15% off
  • Standard
    100 pages
    English and French language
    sale 15% off