IEC 60335-2-73:2002+AMD1:2006+AMD2:2009 CSV

Household and similar electrical appliances - Safety - Part 2-73: Particular requirements for fixed immersion heaters

IEC 60335-2-73:2002+A1:2006+A2:2009 Deals with the safety of fixed electric immersion heaters intended for installation in a water tank for heating water to temperature below its boiling point. The rated voltage is not more than 250 V for single-phase and 480 V for other appliances. This consolidated version consists of the second edition (2002), its amendment 1 (2006) and its amendment 2 (2009). Therefore, no need to order amendments in addition to this publication.
This publication is to be read in conjunction with IEC 60335-1:2006.

Appareils électrodomestiques et analogues - Sécurité - Partie 2-73: Règles particulières pour les thermoplongeurs installés à poste fixe

La CEI 60335-2-73:2002+A1:2006+A2:2009 Traite de la sécurité des thermoplongeurs électriques installés à poste fixe à usages domestiques et analogues, destinés à être installés dans une cuve pour chauffer de l'eau à une température inférieure à l'ébullition. La tension assignée n'est pas supérieure à 250 V pour les appareils monophasés et à 480 V pour les autres appareils.  Cette version consolidée comprend la deuxième édition (2002), son amendement 1 (2006) et son amendement 2 (2009). Il n'est donc pas nécessaire de commander les amendements avec cette publication.
Cette publication doit être lue conjointement avec la CEI 60335-1:2006.

General Information

• Status: Published
• Publication Date: 24-Nov-2009
• ICS: 01 - GENERALITIES. TERMINOLOGY. STANDARDIZATION. DOCUMENTATION
• ICS: 91.140.65 - Water heating equipment
• Technical Committee: TC 61 - Safety of household and similar electrical appliances
• Current Stage: PPUB - Publication issued
• Start Date: 25-Nov-2009
• Completion Date: 25-Nov-2009

Standards Content (Sample)

IEC 60335-2-73
®
Edition 2.2 2009-11
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Household and similar electrical appliances – Safety –
Part 2-73: Particular requirements for fixed immersion heaters

Appareils électrodomestiques et analogues – Sécurité –
Partie 2-73: Règles particulières pour les thermoplongeurs installés à poste fixe
IEC 60335-2-73:2002+A1:2006+A2:2009

---------------------- Page: 1 ----------------------
THIS PUBLICATION IS COPYRIGHT PROTECTED
Copyright © 2009 IEC, Geneva, Switzerland

All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by
any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either IEC or
IEC's member National Committee in the country of the requester.
If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publication,
please contact the address below or your local IEC member National Committee for further information.

Droits de reproduction réservés. Sauf indication contraire, aucune partie de cette publication ne peut être reproduite
ni utilisée sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie
et les microfilms, sans l'accord écrit de la CEI ou du Comité national de la CEI du pays du demandeur.
Si vous avez des questions sur le copyright de la CEI ou si vous désirez obtenir des droits supplémentaires sur cette
publication, utilisez les coordonnées ci-après ou contactez le Comité national de la CEI de votre pays de résidence.

IEC Central Office
3, rue de Varembé
CH-1211 Geneva 20
Switzerland
Email: [e-mail]
Web: www.iec.ch

About the IEC
The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes
International Standards for all electrical, electronic and related technologies.

About IEC publications
The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the
latest edition, a corrigenda or an amendment might have been published.
ƒ Catalogue of IEC publications: www.iec.ch/searchpub
The IEC on-line Catalogue enables you to search by a variety of criteria (reference number, text, technical committee,…).
It also gives information on projects, withdrawn and replaced publications.
ƒ IEC Just Published: www.iec.ch/online_news/justpub
Stay up to date on all new IEC publications. Just Published details twice a month all new publications released. Available
on-line and also by email.
ƒ Electropedia: www.electropedia.org
The world's leading online dictionary of electronic and electrical terms containing more than 20 000 terms and definitions
in English and French, with equivalent terms in additional languages. Also known as the International Electrotechnical
Vocabulary online.
ƒ Customer Service Centre: www.iec.ch/webstore/custserv
If you wish to give us your feedback on this publication or need further assistance, please visit the Customer Service
Centre FAQ or contact us:
Email: [e-mail]
Tel.: [phone]
Fax: [phone]


A propos de la CEI
La Commission Electrotechnique Internationale (CEI) est la première organisation mondiale qui élabore et publie des
normes internationales pour tout ce qui a trait à l'électricité, à l'électronique et aux technologies apparentées.

A propos des publications CEI
Le contenu technique des publications de la CEI est constamment revu. Veuillez vous assurer que vous possédez
l’édition la plus récente, un corrigendum ou amendement peut avoir été publié.
ƒ Catalogue des publications de la CEI: www.iec.ch/searchpub/cur_fut-f.htm
Le Catalogue en-ligne de la CEI vous permet d’effectuer des recherches en utilisant différents critères (numéro de référence,
texte, comité d’études,…). Il donne aussi des informations sur les projets et les publications retirées ou remplacées.
ƒ Just Published CEI: www.iec.ch/online_news/justpub
Restez informé sur les nouvelles publications de la CEI. Just Published détaille deux fois par mois les nouvelles
publications parues. Disponible en-ligne et aussi par email.
ƒ Electropedia: www.electropedia.org
Le premier dictionnaire en ligne au monde de termes électroniques et électriques. Il contient plus de 20 000 termes et
définitions en anglais et en français, ainsi que les termes équivalents dans les langues additionnelles. Egalement appelé
Vocabulaire Electrotechnique International en ligne.
ƒ Service Clients: www.iec.ch/webstore/custserv/custserv_entry-f.htm
Si vous désirez nous donner des commentaires sur cette publication ou si vous avez des questions, visitez le FAQ du
Service clients ou contactez-nous:
Email: [e-mail]
Tél.: [phone]
Fax: [phone]

---------------------- Page: 2 ----------------------
IEC 60335-2-73
®
Edition 2.2 2009-11
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Household and similar electrical appliances – Safety –
Part 2-73: Particular requirements for fixed immersion heaters

Appareils électrodomestiques et analogues – Sécurité –
Partie 2-73: Règles particulières pour les thermoplongeurs installés à poste fixe

INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
PRICE CODE
INTERNATIONALE
CE
CODE PRIX
ICS 91.140.65 ISBN 978-2-88910-163-4
® Registered trademark of the International Electrotechnical Commission
Marque déposée de la Commission Electrotechnique Internationale

---------------------- Page: 3 ----------------------
– 2 – 60335-2-73 © IEC:2002+A1:2006
+A2:2009
CONTENTS
FOREWORD.3
INTRODUCTION.5

1 Scope.6
2 Normative references .7
3 Definitions .7
4 General requirement.7
5 General conditions for the tests .7
6 Classification.7
7 Marking and instructions.7
8 Protection against access to live parts.8
9 Starting of motor-operated appliances .8
10 Power input and current .8
11 Heating .8
12 Void.8
13 Leakage current and electric strength at operating temperature.8
14 Transient overvoltages .8
15 Moisture resistance .8
16 Leakage current and electric strength.8
17 Overload protection of transformers and associated circuits .9
18 Endurance.9
19 Abnormal operation .9
20 Stability and mechanical hazards .9
21 Mechanical strength .9
22 Construction .9
23 Internal wiring.10
24 Components .10
25 Supply connection and external flexible cords .10
26 Terminals for external conductors.10
27 Provision for earthing .10
28 Screws and connections .10
29 Clearances, creepage distances and solid insulation .10
30 Resistance to heat and fire.10
31 Resistance to rusting.11
32 Radiation, toxicity and similar hazards.11


Annexes .12


Bibliography.12

---------------------- Page: 4 ----------------------
60335-2-73 © IEC:2002+A1:2006 – 3 –
+A2:2009
INTERNATIONAL ELECTROTECHNICAL COMMISSION
___________

HOUSEHOLD AND SIMILAR ELECTRICAL APPLIANCES –
SAFETY –

Part 2-73: Particular requirements for fixed immersion heaters



FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
This part of International Standard IEC 60335 has been prepared by IEC technical committee 61:
Safety of household and similar electrical appliances.
This consolidated version of IEC 60335-2-73 consists of the second edition (2002)
[documents 61/2176/FDIS and 61/2257/RVD], its amendment 1 (2006) [documents
61/2957/FDIS and 61/2987/RVD] and its amendment 2 (2009) [documents 61/3866/FDIS and
61/3912A/RVD].
The technical content is therefore identical to the base edition and its amendments and has
been prepared for user convenience.
It bears the edition number 2.2.
A vertical line in the margin shows where the base publication has been modified by
amendments 1 and 2.

---------------------- Page: 5 ----------------------
– 4 – 60335-2-73 © IEC:2002+A1:2006
+A2:2009
The French version of this standard has not been voted upon.
This bilingual version (2005-04) replaces the English version.
This part 2 is to be used in conjunction with the latest edition of IEC 60335-1 and its
amendments. It was established on the basis of the fourth edition (2001) of that standard.
NOTE 1 When “Part 1” is mentioned in this standard, it refers to IEC 60335-1.
This part 2 supplements or modifies the corresponding clauses in IEC 60335-1, so as to
convert that publication into the IEC standard: Safety requirements for fixed electric
immersion heaters.
When a particular subclause of Part 1 is not mentioned in this part 2, that subclause applies
as far as is reasonable. When this standard states "addition", "modification", or "replacement",
the relevant text in Part 1 is to be adapted accordingly.
NOTE 2 The following numbering system is used:
– subclauses, tables and figures that are numbered starting from 101 are additional to those in Part 1;
– unless notes are in a new subclause or involve notes in Part 1, they are numbered starting from 101, including
those in a replaced clause or subclause;
– additional annexes are lettered AA, BB, etc.
NOTE 3 The following print types are used:
– requirements: in roman type;
– test specifications: in italic type;
– notes: in small roman type.
Words in bold in the text are defined in Clause 3. When a definition concerns an adjective, the adjective and the
associated noun are also in bold.
The following differences exist in the countries indicated below.
– 3.1.9: Normal operation is different (USA).
– 6.1: Class 0I appliances are allowed (Japan).
– 24.101: The requirement is not applicable (USA).
The committee has decided that the contents of the base publication and its amendments will
remain unchanged until the maintenance result date indicated on the IEC web site under
"http://webstore.iec.ch" in the data related to the specific publication. At this date,
the publication will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.

2
NOTE The attention of National Committees is drawn to the fact that equipment manufacturers and testing
organizations may need a transitional period following publication of a new, amended or revised IEC publication in
which to make products in accordance with the new requirements and to equip themselves for conducting new or
revised tests.
It is the recommendation of the committee that the content of the amendment 2 be adopted for implementation
nationally not earlier than 12 months or later than 36 months from the date of publication.

---------------------- Page: 6 ----------------------
60335-2-73 © IEC:2002+A1:2006 – 5 –
+A2:2009
INTRODUCTION
It has been assumed in the drafting of this International Standard that the execution of its
provisions is entrusted to appropriately qualified and experienced persons.
This standard recognizes the internationally accepted level of protection against hazards such
as electrical, mechanical, thermal, fire and radiation of appliances when operated as in
normal use taking into account the manufacturer's instructions. It also covers abnormal
situations that can be expected in practice and takes into account the way in which
electromagnetic phenomena can affect the safe operation of appliances.
This standard takes into account the requirements of IEC 60364 as far as possible so that
there is compatibility with the wiring rules when the appliance is connected to the supply
mains. However, national wiring rules may differ.
If an appliance within the scope of this standard also incorporates functions that are covered
by another part 2 of IEC 60335, the relevant part 2 is applied to each function separately, as
far as is reasonable. If applicable, the influence of one function on the other is taken into
account.
2 When a part 2 standard does not include additional requirements to cover hazards dealt with
in Part 1, Part 1 applies.
NOTE 1 This means that the technical committees responsible for the part 2 standards have determined that it is
not necessary to specify particular requirements for the appliance in question over and above the general
requirements.
This standard is a product family standard dealing with the safety of appliances and takes
precedence over horizontal and generic standards covering the same subject.
NOTE 2 Horizontal and generic standards covering a hazard are not applicable since they have been taken into
consideration when developing the general and particular requirements for the IEC 60335 series of standards. For
example, in the case of temperature requirements for surfaces on many appliances, generic standards, such as
ISO 13732-1 for hot surfaces, are not applicable in addition to Part 1 or part 2 standards.
An appliance that complies with the text of this standard will not necessarily be considered to
comply with the safety principles of the standard if, when examined and tested, it is found to
have other features that impair the level of safety covered by these requirements.
An appliance employing materials or having forms of construction differing from those detailed
in the requirements of this standard may be examined and tested according to the intent of
the requirements and, if found to be substantially equivalent, may be considered to comply
with the standard.

---------------------- Page: 7 ----------------------
– 6 – 60335-2-73 © IEC:2002+A1:2006
+A2:2009
HOUSEHOLD AND SIMILAR ELECTRICAL APPLIANCES –
SAFETY –

Part 2-73: Particular requirements for fixed immersion heaters



1 Scope
This clause of Part 1 is replaced by the following.
This International Standard deals with the safety of fixed electric immersion heaters for
household and similar purposes that are intended for installation in a water tank open to the
atmosphere for heating water to a temperature below its boiling point. The rated voltage is
not more than 250 V for single-phase appliances and 480 V for other appliances.
NOTE 101 The water tank may have alternative means for heating water, such as the circulation of hot water
supplied from a separate boiler.
NOTE 102 Immersion heaters having a rated power input up to 25 kW for incorporation as an alternative heating
source in central heating boilers are also within the scope of this standard.
Appliances not intended for normal household use but which nevertheless may be a source of
danger to the public, such as appliances intended to be used by laymen in shops, in light
industry and on farms, are within the scope of this standard.
As far as is practicable, this standard deals with the common hazards presented by
appliances that are encountered by all persons in and around the home. However, in general,
it does not take into account
2 – persons (including children) whose
• physical, sensory or mental capabilities; or
• lack of experience and knowledge
prevents them from using the appliance safely without supervision or instruction;
– children playing with the appliance.
NOTE 103 Attention is drawn to the fact that
– for appliances intended to be used in vehicles or on board ships or aircraft, additional requirements may be
necessary;
– in many countries additional requirements are specified by the national health authorities, the national
authorities responsible for the protection of labour, the national water supply authorities and similar
authorities.
NOTE 104 This standard does not apply to
– appliances intended exclusively for industrial purposes;
– appliances intended to be used in locations where special conditions prevail, such as the presence of a
corrosive or explosive atmosphere (dust, vapour or gas);
– heating elements incorporated in appliances such as
• appliances for heating liquids (IEC 60335-2-15);
• storage water heaters (IEC 60335-2-21);
• instantaneous water heaters (IEC 60335-2-35);
– aquarium heaters (IEC 60335-2-55);
− portable immersion heaters (IEC 60335-2-74);
– engine preheaters such as those for cars and buses.

---------------------- Page: 8 ----------------------
60335-2-73 © IEC:2002+A1:2006 – 7 –
+A2:2009
2 Normative references
This clause of Part 1 is applicable.
3 Definitions
This clause of Part 1 is applicable except as follows.
3.1.9 Replacement:
normal operation
operation of the appliance after installation in the smallest tank specified, the tank being
thermally insulated and filled with water
NOTE 101 Accessible parts of the appliance are not thermally insulated.
4 General requirement
This clause of Part 1 is applicable.
5 General conditions for the tests
This clause of Part 1 is applicable except as follows.
5.2 Addition:
NOTE 101 Additional appliances may be required for the tests of Clause 19.
6 Classification
This clause of Part 1 is applicable except as follows.
6.1 Addition:
Immersion heaters shall be class I, class II or class III.

7 Marking and instructions
This clause of Part 1 is applicable except as follows.
7.1 Modification:
Appliances for multiple supply shall be marked with their rated power input for each supply
circuit.
Addition:
Appliances shall be marked "Do not cover".

---------------------- Page: 9 ----------------------
– 8 – 60335-2-73 © IEC:2002+A1:2006
+A2:2009
7.12.1 Addition:
The installation instructions shall include the substance of the following:
– the type and dimensions of the tank in which the immersion heater can be installed;
– the positioning of the immersion heater within the tank;
– a statement that the installer must check that there is water in the tank before the
immersion heater is first switched on;
– a statement that the immersion heater is to be installed only in a system where the
heating element is always below water level, such as in a cistern-fed tank, if applicable.
8 Protection against access to live parts
This clause of Part 1 is applicable.
9 Starting of motor-operated appliances
This clause of Part 1 is not applicable.
10 Power input and current
This clause of Part 1 is applicable.
11 Heating
This clause of Part 1 is applicable except as follows.
11.7 Addition:
Appliances are operated until steady conditions are established. However, the test is
terminated after 24 h provided that a thermal control has operated.
12 Void
13 Leakage current and electric strength at operating temperature
This clause of Part 1 is applicable.
14 Transient overvoltages
This clause of Part 1 is applicable.
15 Moisture resistance
This clause of Part 1 is applicable.
16 Leakage current and electric strength
This clause of Part 1 is applicable.

---------------------- Page: 10 ----------------------
60335-2-73 © IEC:2002+A1:2006 – 9 –
+A2:2009
17 Overload protection of transformers and associated circuits
This clause of Part 1 is applicable.
18 Endurance
This clause of Part 1 is not applicable.
19 Abnormal operation
This clause of Part 1 is applicable except as follows.
19.2 Addition:
Appliances are operated with the tank empty, any thermal control that operates during the test
of Clause 11 being short-circuited.
NOTE 101 If more than one thermal control operates during the test of Clause 11, they are short-circuited in turn.
The test is not carried out on immersion heaters intended to be installed in a system where
the heating element is always below water level, such as in a cistern-fed tank.
19.4 Modification:
Appliances are operated with the tank filled with water to at least 10 mm above the highest
point of the heating element, or the highest level allowed by the construction.
The water temperature shall not exceed 98 °C.
20 Stability and mechanical hazards
This clause of Part 1 is applicable.
21 Mechanical strength
This clause of Part 1 is applicable.
22 Construction
This clause of Part 1 is applicable except as follows.
22.101 Appliances shall be supplied with a seal or similar means to ensure that there is no
leakage from the tank after installation.
Compliance is checked by inspection during the test of Clause 11.
22.102 The compartment containing the supply terminals shall be prevented from rotating by
more than 180° with respect to the fixed part of the immersion heater.
Compliance is checked by inspection.

---------------------- Page: 11 ----------------------
– 10 – 60335-2-73 © IEC:2002+A1:2006
+A2:2009
23 Internal wiring
This clause of Part 1 is applicable.
24 Components
This clause of Part 1 is applicable except as follows.
24.101 Thermal cut-outs incorporated for compliance with Clause 19 shall not be self-
resetting. They shall operate independently of the thermostat.
Compliance is checked by inspection.
25 Supply connection and external flexible cords
This clause of Part 1 is applicable.
26 Terminals for external conductors
This clause of Part 1 is applicable.
27 Provision for earthing
This clause of Part 1 is applicable except as follows.
27.1 Addition:
Metal parts of class I immersion heaters that are in contact with water shall be permanently
connected to the earthing terminal.
28 Screws and connections
This clause of Part 1 is applicable.
29 Clearances, creepage distances and solid insulation
This clause of Part 1 is applicable.
30 Resistance to heat and fire
This clause of Part 1 is applicable except as follows.
30.2.2 Not applicable.

---------------------- Page: 12 ----------------------
60335-2-73 © IEC:2002+A1:2006 – 11 –
+A2:2009
31 Resistance to rusting
This clause of Part 1 is applicable.
32 Radiation, toxicity and similar hazards
This clause of Part 1 is applicable.

---------------------- Page: 13 ----------------------
– 12 – 60335-2-73 © IEC:2002+A1:2006
+A2:2009
Annexes
The annexes of Part 1 are applicable.

Bibliography
The bibliography of Part 1 is applicable except as follows.
Addition:
IEC 60335-2-15, Household and similar electrical appliances – Safety – Part 2-15: Particular
requirements for appliances for heating liquids
IEC 60335-2-21, Household and similar electrical appliances – Safety – Part 2-21: Particular
requirements for storage water heaters
IEC 60335-2-35, Household and similar electrical appliances – Safety – Part 2-35: Particular
requirements for instantaneous water heaters
IEC 60335-2-55, Household and similar electrical appliances – Safety – Part 2-55: Particular
requirements for electrical appliances for use with aquariums and garden ponds
IEC 60335-2-74, Household and similar electrical appliances – Safety – Part 2-74: Particular
requirements for portable immersion heaters
ISO 13732-1, Ergonomics of the thermal environment – Methods for the assessment of human
2
responses to contact with surfaces – Part 1: Hot surfaces


___________

---------------------- Page: 14 ----------------------
– 14 – 60335-2-73 © CEI:2002+A1:2006
+A2:2009
SOMMAIRE
AVANT-PROPOS.15
INTRODUCTION.17

1 Domaine d’application .18
2 Références normatives.
...