Rotating electrical machinery - Natural graphite brush for slip-ring in wound rotor-type induction motor - Application information

IEC TR 63021:2016(E) presents technical characteristics, application results and practical information on NG-brush for slip-ring obtained through the application of NG-brush in various kinds of wound rotor-type induction motor (large-size water pump, belt conveyer, lift, winder motor, grinding mill and crusher in coal or ore mine; crane, rolling mill, compressor and winder motor for boring in oil or gas facility).

General Information

Status
Published
Publication Date
05-Sep-2016
Technical Committee
Drafting Committee
Current Stage
PPUB - Publication issued
Start Date
30-Nov-2016
Completion Date
06-Sep-2016
Ref Project

Buy Standard

Technical report
IEC TR 63021:2016 - Rotating electrical machinery - Natural graphite brush for slip-ring in wound rotor-type induction motor - Application information
English language
12 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)


IEC TR 63021 ®
Edition 1.0 2016-09
TECHNICAL
REPORT
Rotating electrical machinery – Natural graphite brush for slip-ring in wound
rotor-type induction motor – Application information

All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form
or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from
either IEC or IEC's member National Committee in the country of the requester. If you have any questions about IEC
copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or
your local IEC member National Committee for further information.

IEC Central Office Tel.: +41 22 919 02 11
3, rue de Varembé Fax: +41 22 919 03 00
CH-1211 Geneva 20 info@iec.ch
Switzerland www.iec.ch
About the IEC
The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes
International Standards for all electrical, electronic and related technologies.

About IEC publications
The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the
latest edition, a corrigenda or an amendment might have been published.

IEC Catalogue - webstore.iec.ch/catalogue Electropedia - www.electropedia.org
The stand-alone application for consulting the entire The world's leading online dictionary of electronic and
bibliographical information on IEC International Standards, electrical terms containing 20 000 terms and definitions in
Technical Specifications, Technical Reports and other English and French, with equivalent terms in 15 additional
documents. Available for PC, Mac OS, Android Tablets and languages. Also known as the International Electrotechnical
iPad. Vocabulary (IEV) online.

IEC publications search - www.iec.ch/searchpub IEC Glossary - std.iec.ch/glossary
The advanced search enables to find IEC publications by a 65 000 electrotechnical terminology entries in English and
variety of criteria (reference number, text, technical French extracted from the Terms and Definitions clause of
committee,…). It also gives information on projects, replaced IEC publications issued since 2002. Some entries have been
and withdrawn publications. collected from earlier publications of IEC TC 37, 77, 86 and

CISPR.
IEC Just Published - webstore.iec.ch/justpublished
Stay up to date on all new IEC publications. Just Published IEC Customer Service Centre - webstore.iec.ch/csc
details all new publications released. Available online and If you wish to give us your feedback on this publication or
also once a month by email. need further assistance, please contact the Customer Service
Centre: csc@iec.ch.
IEC TR 63021 ®
Edition 1.0 2016-09
TECHNICAL
REPORT
Rotating electrical machinery – Natural graphite brush for slip-ring in wound

rotor-type induction motor – Application information

INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
ICS 29.160.01 ISBN 978-2-8322-3602-4

– 2 – IEC TR 63021:2016 © IEC 2016
CONTENTS
FOREWORD . 3
INTRODUCTION . 5
1 Scope . 6
2 Normative references. 6
3 Terms and definitions . 6
4 General remarks . 7
5 General conditions of brush and slip-ring for stability in the operation of a wound
rotor-type induction motor . 7
5.1 Fire-spark . 7
5.2 Life . 7
5.3 Temperature . 8
5.4 Dust diffusion . 8
5.5 Noise . 8
6 Operating characteristics of natural graphite brush for slip-ring in a wound
rotor-type induction motor . 8
6.1 Current density . 8
6.2 Vibration absorbing ability . 8
6.3 Temperature . 8
6.4 Brush’s pressure . 9
7 Testing method . 9
8 Application result . 9
8.1 Fire-spark . 9
8.2 Wear and life of brush . 9
8.3 Life of slip-ring . 9
8.4 Environmental pollution . 9
8.4.1 Dust diffusion by wear of brush . 9
8.4.2 Pollution by noise . 10
8.5 Economic profit . 10
8.5.1 Brush price . 10
8.5.2 Brush life . 10
8.5.3 No accident due to dust diffusion and slip-ring’s life . 10
Annex A (informative) Data from practical application. 11
Bibliography . 12

Table 1 – Typical kinds of brushes . 7
Table 2 – NG-brush’s bulk density, electric resistivity and current density compared with
the copper brush . 8
Table 3 – Comparison of properties for the assessment of vibration absorbing ability . 8
Table 4 – Wear and life of brush . 9
Table 5 – Comparison of wear of NG-brush and copper brush . 9
Table A.1 – Data from practical application . 11

INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
ROTATING ELECTRICAL MACHINERY –

Natural graphite brush for slip-ring in wound
rotor-type induction motor – Application information

FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international
co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in
addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports,
Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their
preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with
may participate in this preparatory work. International, governmental and non-governmental organizations liaising
with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for
Standardization (ISO) in accordance with conditions determined by agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence between
any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses
arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent
rights. IEC shall not be held responsible for identifying any or all such patent rights.
The main task of IEC technical committees is to prepare International Standards. However, a
technical committee may propose the publication of a Technical Report when it has collected
data of a different kind from that which is normally published as an International Standard, for
example "state of the art".
IEC TR 63021, which is a Technical Report, has been prepared by IEC technical committee 2:
Rotating machinery.
The text of this Technical Report is based on the following documents:
Enquiry draft Report on voting
2/1794/DTR 2/1823A/RVC
Full information on the voting for the approval of this Technical Report can be found in the report
on voting indicated in the above table.
This document has been drafted in accordance with the ISO/IEC Directives, Part 2.

– 4 – IEC TR 63021:2016 © IEC 2016
The committee has decided that the contents of this document will remain unchanged until the
stability date indicated on the IEC website under "http://webstore.iec.ch" in the data related to
the specific document. At this date, the document will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.
A bilingual version of this publication may be issued at a later date.

INTRODUCTION
This Technical Report has been prepared after considering implications of the withdrawal of
IEC PAS 62072:2005 and its potential conversion into an International Standard, and after
analysing practical information obtained through the application of natural graphite (NG) brush
for slip-ring in wound-rotor type induction motor, compared with copper brush.
Practical values obtained through the application of NG-brushes into slip-rings in various kinds
of wound rotor-type induction motor are given in Annex A.

– 6 – IEC TR 63021:2016 © IEC 2016
ROTATING ELECTRICAL MACHINERY –

Natural graphite brush for slip-ring in wound
rotor-type induction motor – Application information

1 Scope
This document presents technical characteristics, application results and practical information
on NG-brush for slip-ring obtained through the application of NG-brush in various kinds of
wound rotor-type induction motor (large-size water pump, belt conveyer, lift, winder motor,
grinding mill and crusher in coal or ore mine; crane, rolling mill, compressor and winder motor for
boring in oil or gas facility).
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies.
For undated references, the latest edition of the referenced document (including any
ame
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.