IEC TS 61508-3-2:2024

Functional safety of electrical/electronic/programmable electronic safety-related systems - Part 3-2: Requirements and guidance in the use of mathematical and logical techniques for establishing exact properties of software and its documentation

IEC TS 61508-3-2:2024 covers the general assurance of dependable software used in critical operational-technology (OT) which is running on hardware devices which are specified as part of the OT application. It is particularly aimed at safety-related software which is being developed according to the E/E/PE software functional safety standard IEC 61508-3; in particular, the development of the software follows a Formal Safety Requirements Specification. Successful use of some or all of the assurance points specified in this document enhances the confidence that a particular piece of safety-related software meets the requirements of the SIL of the safety function which it (partially or fully) implements, and thereby increases the systematic capability of the software.

General Information

• Status: Published
• Publication Date: 25-Aug-2024
• ICS: 25.040.40 - Industrial process measurement and control
• Technical Committee: SC 65A - System aspects
• Drafting Committee: PT 61508-3-2 - TC 65/SC 65A/PT 61508-3-2
• Current Stage: PPUB - Publication issued
• Start Date: 20-Sep-2024
• Completion Date: 26-Aug-2024

Standards Content (Sample)

IEC TS 61508-3-2 ®
Edition 1.0 2024-08
TECHNICAL
SPECIFICATION
Functional safety of electrical/electronic/programmable electronic safety-related
systems –
Part 3-2: Requirements and guidance in the use of mathematical and logical
techniques for establishing exact properties of software and its documentation

All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form
or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from
either IEC or IEC's member National Committee in the country of the requester. If you have any questions about IEC
copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or
your local IEC member National Committee for further information.

IEC Secretariat Tel.: [phone]
3, rue de Varembé [e-mail]
CH-1211 Geneva 20 www.iec.ch
Switzerland
About the IEC
The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes
International Standards for all electrical, electronic and related technologies.

About IEC publications
The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the
latest edition, a corrigendum or an amendment might have been published.

IEC publications search - webstore.iec.ch/advsearchform IEC Products & Services Portal - products.iec.ch
The advanced search enables to find IEC publications by a Discover our powerful search engine and read freely all the
variety of criteria (reference number, text, technical publications previews, graphical symbols and the glossary.
committee, …). It also gives information on projects, replaced With a subscription you will always have access to up to date
and withdrawn publications. content tailored to your needs.

IEC Just Published - webstore.iec.ch/justpublished
Electropedia - www.electropedia.org
Stay up to date on all new IEC publications. Just Published
The world's leading online dictionary on electrotechnology,
details all new publications released. Available online and once
containing more than 22 500 terminological entries in English
a month by email.
and French, with equivalent terms in 25 additional languages.

Also known as the International Electrotechnical Vocabulary
IEC Customer Service Centre - webstore.iec.ch/csc
(IEV) online.
If you wish to give us your feedback on this publication or need

further assistance, please contact the Customer Service
Centre: [e-mail].
IEC TS 61508-3-2 ®
Edition 1.0 2024-08
TECHNICAL
SPECIFICATION
Functional safety of electrical/electronic/programmable electronic safety-related

systems –
Part 3-2: Requirements and guidance in the use of mathematical and logical

techniques for establishing exact properties of software and its documentation

INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
ICS 25.040.40  ISBN 978-2-8322-9565-6

– 2 – IEC TS 61508-3-2:2024 © IEC 2024
CONTENTS
FOREWORD . 3
INTRODUCTION . 5
1 Scope . 6
2 Normative references . 6
3 Terms, definitions and abbreviations . 6
3.1 Terms and definitions . 6
3.2 Abbreviations . 15
4 Conformance to this document . 15
5 Formal safety requirements specification . 16
6 Formal software architecture / Design specification . 16
7 Higher-level programming languages: Selection of ESCL . 17
8 Compilation to object code . 17
9 Run-time errors and exceptions . 17
10 Applicable techniques . 18
Annex A (normative) Applicable Mathematical and Logical Techniques . 19
Annex B (informative) Specific Mathematical and Logical Techniques . 21
Annex C (informative) Properties assured by application of specific M< techniques . 24
Annex D (informative) Software refinement from safety specification to Code . 26
D.1 Transformation . 26
D.2 Refinement . 26
Bibliography . 27

Table A.1 – M< Techniques . 19
Table B.1 – Specific M< Techniques/Tools . 21
Table C.1 – Properties Assured by M< Techniques . 24

INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
FUNCTIONAL SAFETY OF ELECTRICAL/ELECTRONIC/PROGRAMMABLE
ELECTRONIC SAFETY-RELATED SYSTEMS –

Part 3-2: Requirements and guidance in the use of mathematical
and logical techniques for establishing exact properties
of software and its documentation

FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international
co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and
in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports,
Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their
preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with
may participate in this preparatory work. International, governmental and non-governmental organizations liaising
with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for
Standardization (ISO) in accordance with conditions determined by agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence between
any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) IEC draws attention to the possibility that the implementation of this document may involve the use of (a)
patent(s). IEC takes no position concerning the evidence, validity or applicability of any claimed patent rights in
respect thereof. As of the date of publication of this document, IEC had not received notice of (a) patent(s), which
may be required to implement this document. However, implementers are cautioned that this may not represent
the latest information, which may be obtained from the patent database available at https://patents.iec.ch. IEC
shall not be held responsible for identifying any or all such patent rights.
IEC TS 61508-3-2 has been prepared by subcommittee 65A: System aspects, of IEC technical
committee 65: Industrial-process measurement, control and automation. It is a Technical
Specification.
– 4 – IEC TS 61508-3-2:2024 © IEC 2024
The text of this Technical Specification is based on the following documents:
Draft Report on voting
65A/1113/DTS 65A/1143/RVDTS
Full information on the voting for its approval can be found in the report on voting indicated in
the above table.
The language used for the development of this Technical Specification is English.
This document was drafted in accordance with ISO/IEC Directives, Part 2, and developed in
accordance with ISO/IEC Directives, Part 1 and ISO/IEC Directives, IEC Supplement, available
at www.iec.ch/members_experts/refdocs. The main document types developed by IEC are
described in greater detail at www.iec.ch/publications.
A list of all parts in the IEC 61508 series, published under the general title Functional safety of
electrical/electronic/programmable electronic safety-related systems, can be found on the IEC
website.
The committee has decided that the contents of this document will remain unchanged until the
stability date indicated on the IEC website under webstore.iec.ch in the data related to the
specific document. At this date, the document will be
• reconfirmed,
• withdrawn, or
• revised.
INTRODUCTION
IEC 61508-1:2010 through IEC 61508-7:2010 forms the series of basic standards for the
functional safety of electric, electronic and programmable electronic systems (E/E/PE systems).
It covers the life cycle of these systems. The major part of the functionality of such systems is
often implemented in software. IEC 61508-3:2010 sets software requirements.
IEC 61508-3:2010 Annex A (normative) and Annexes B and C (informative) contain tables
listing various techniques and measures, and provide some guidance to the selection of such
techniques for different safety integrity levels (SIL). It lists general categories and gives different
levels of recommendation for these, such as "not recommended", "recommended" or "highly
recommended", as well as more specific techniques for various phases of software
development.
These techniques and measures are a mix of generic and specific. The phrase "Formal
Methods" as used in IEC 61508-3 refers to the use of mathematical and logical techniques for
specifying, assessing, designing and verifying software. Today, such methods are available for
specifying requirements, for the assessment of the design, for checking source code and object
code and for the derivation of test suites, and for monitoring the correct operation of software
at runtime. In this document, we refer to these methods by using the description as
mathematical and logical techniques (M< sometimes doubled as M< techniques). Some
of the M< techniques in this document are not restricted to software development, being
equally applicable to other digital-system-based engineering technologies. None of the M<
techniques are limited to the domain of safety-related software systems, although in this
document only safety-related applications of M< techniques are explicitly addressed.
Use of the recommended methods of IEC 61508-3:2010, Annexes A, B and C do not rule out,
for example, susceptibility of the software to run-time failure. State of the art in software
development enables various types of run-time failures to be ruled out through rigorous
development of the software. It is possible using techniques identified here to assure freedom
from many types of software run-time failures.

– 6 – IEC TS 61508-3-2:2024 © IEC 2024
FUNCTIONAL SAFETY OF ELECTRICAL/ELECTRONIC/PROGRAMMABLE
ELECTRONIC SAFETY-RELATED SYSTEMS –

Part 3-2: Requirements and guidance in the use of mathematical
and logical techniques for establishing exact properties
of software and its documentation

1 Scope
This Technical Specification, part of the IEC 61508 series, covers the general assurance of
dependable software used in critical operation
...